小兔耳戒指

結繩牽緣
122 followers
11 Video Views·Dec 31, 2022
小兔耳戒指
Rabbit ears can be upright or flat
Open the material pack and take out six 60-centimeter wires
Two white and one red braided ear put aside first
Three 60-centimeter white wires reach the end connect the main body
Since all white wires are hard to see switch to colored wires for demonstration
Secure the end position with a clip
Center as the axis both sides flattened
The left line emerges from below
The right line goes through from above
Tighten
The right line goes through from below
The left line goes through from top to bottom
Tighten the line a set of flat ends completed
Repeat the same method to create another set of truncated data
Bring the three wires from the ear
Fold in half
Cut into 6 pieces of 30 centimeters each
Take a 30-centimeter white thread
Fold in half but the head is hanging on the axis
Can't see clearly use the yellow line as an example
Tie the two groups again
If you like your ears close just cut one set flat
Take another 30-centimeter white thread fold it and hang it
Tie again
Remove it and straighten the wires
The colored wires on both sides are for interference let's set them aside first
Find the central axis
Pull the upper axis line over to make a loop
Note that the axis line is below the truncation
Clamp the flat section and the axis with the clip
Next flatten the overlapping parts of the two axes
Remove after forming several groups
Turn around
Align the axis and pull it down to the level
Looking from the side the axis forms a complete circle
Put it on the clip
Make sure the axis is clamped below the flat section
Start continuing to edit the flat
If it's only 19 millimeters then 19 plus 5 equals 24 millimeters in length
You can try putting your finger through it it should be very loose
Because tightening the axis will definitely cause the length to shrink
The amount of shrinkage depends on how tight or loose you knit
Find the axis and tighten it a bit
Pull both sides together but make sure not to tighten them all at once
You can cut the flat line once you have confirmed the size
Sear the edges to seal them
Cut the inner axis line 1 millimeter in length
Turn it out and melt the thread ends with a small flame to bond them
Turn it over
Prepare the earpiece
A 30-centimeter white wire leave a 3-centimeter wire end on the left and cut it diagonally
Turn around from right to left
Tighten the thread squeeze out the gap
30 centimeter red line folded in half but the head is cut off
Tighten the line and push it to the left
Carve a slanting cut on the right axis
Wrap around once from below the axis
Tighten don't leave any gaps
Wrap around the axis line once more
During this process use your right hand to tighten the loop that has been wrapped on top
This tightens the line creating a small slant cut seam
Squeeze out the gap between the two circles
Push it along the axis
The white line is twisted diagonally on the right axis
Wrap a loop from below
Tighten the thread and then wrap it around once from top to bottom
Tighten the line the red line is diagonally wrapped around the shaft
Circle around once from top to bottom then circle around again
Draw a red line wrap it around once from top to bottom then wrap it again
The axis is obliquely cut on the left axis
Go around in a circle from front to back
Circle around once more from front to back
Turn the white line back and go around in a circle from behind
Go around in a circle from front to back
The red line is diagonally cut
Loop around from the bottom up
Circle once more from bottom top
Another red line loops upward from below
Circle once more from bottom top
Place the white line after the axis
Loop around from behind
The white line loops around from front to back
Turn the white line back and go around in a circle from behind
The white line loops around from front to back
The red line loops around from back to front
Let's go around again
The other red line winds upward in a loop
The red line goes around once from bottom top
Place the white line after the axis
Go around in a circle from front to back
The white line loops around from front to back
Turn the white line back and go around in a circle from behind
The white line once again loops from back to front
The red line loops upward from the bottom
Switch to another thread and wrap it around from the bottom up
Squeeze the white thread onto the axis
Loop around from behind
The white line once again loops from back to front
The left axis loops backward
Tighten
The white line loops around from behind
Pull down the other axis line and make another ear using the same method
After both ears are completed cut off the threads and melt them to bond
