584. Learning Detail on Opening/Shaping/Ribbing a 3-Lb Bowl with Hsin-Chuen Lin 林新春 3磅碗公拉坯示範

Soul of Siberia
114 followers
9 Video Views·May 16, 2021
To see or buy my finished work and pottery tools, please visit my ETSY shop:
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
http://www.etsy.com/shop/potterysquare
To watch more of my throwing videos, please visit my channel:
http://www.youtube.com/user/hsinchuen/videos
To learn more about my back ground, please visit my Website:
www.mypots.net
Follow me on Instagram: hsinchuenlin
Like me on Facebook page: Hsin-Chuen Lin Ceramics
If you look at the camera from the top, you will see that when I'm drilling a hole, I
tend to make a curve here, so that the inside of the ball has a nicer curve.
If you try to open at 90 degrees, then you're going to end up with a gap there, so make
sure that when you are making a ball, plan ahead.
Make sure that you have the curve here.
Personally, I prefer a small foot noodle ball.
You can make your base wider, but my personal preference, I like to have a smaller ball,
so the whole piece looks lighter.
Before I move, I usually like to cold the surface, so it's slippery.
I don't usually throw with a sponge, because using a sponge, you tend to squeeze a lot
of water.
I just dip my fingertip in the water, and just take it to the surface and smooth it.
I think this is thin enough, so I will start to shape it, stretch it a tiny little bit.
I usually like to take care of the outside first, so using a metal rip to remove all
I compress and smooth the rim a bit, before I take care of the inside of the ball.
You can see that when I'm shaping, I slow down my wheel speed.
The outside looks good, and if you like, you can remove a little bit of clay from the corner.
When you are taking care of the inside of the bottom, the clay is not in the way.
I use a wooden knife to remove it, and then my number 10 cutting knife to undercut it.
The number 10 knife is good for undercutting, and also very good for trimming to level the rim.
But in this case, I don't have to do that, because my rim is very stable, very smooth.
Now, the inside here, especially this part here from the top, this part here is sometimes
not quite smooth.
You might have a little bump.
You can use a wooden rip, or any kind of rip, but my rip is a special design, so there's
a curve on both sides here, so it's easier to compress without catching or getting any
unwanted chattering.
Just start it from the very center, and then I gradually roll the wooden rip sideways.
So this is what I do.
Put it there, and using this part here to compress it, this part here, and then kind
of rotate my rip, and if you want to push it a little bit shallower, you can tip over
your rip.
If you don't, just hold straight, and if you tip over, the side of the rip is compressing
down the piece, so your piece will be a little bit shallower.
And you don't need to go all the way here, just here, you can just start by using your
hand to stretch.
The most important part is from this, the center to here, to about one third of it.
That corner is very hard to take care of, but you don't have the right tool.
So I remove the water, you can see the inside, it's very smooth, nicely curved.
And if you don't like the wooden texture from the rip, you can use a metal rip to remove
it.
Okay, so this is the metal rip, but you've got to watch out when you're trying to use
a very sharp edge of the tool, you don't want to cross over the very center point.
If you cross over, it's against the direction of the wheel, and then you will get, your
tool is going to get caught in that, and the surface is not going to be nice.
So always start from maybe one eighth or maybe a quarter of an inch away from the center
and start to move.
If your wheel is spinning counterclockwise, move to your right, if your wheel is spinning
clockwise, move to your left.
And you can slightly bend, so your tool will have a nicer curve following through the metal
rip.
Alright, so that's the ball, and if you're on the rim, visually it looks, the ball is
very light, you can actually make the rim, use the chamois to squeeze it, so the rim
is a little bit thinner, so visually, okay, give people some impression that this ball
is very light, very thin.
And by just squeezing the rim a tiny little bit, you put your both fingers there, and
then just finger tip to compress it, and then this part visually looks thin, but actually
it's not that thin.
Okay, so that's the demonstration of throwing this ball.
This ball is about three pounds of clay.
I don't want to throw it very, very thin, because when it's very thin, you don't keep
the foam nice and straight, so sometimes it can wobble if you stretch too much, make it
too thin.
So give it a little bit of a thickness, and you can remove the clay at the trim, so if
you want to make it thinner, wait until the clay gets there, and use a very sharp knife,
a sharp trimming tool, you can remove the clay easily, so you don't need to throw it
very thin.
Okay, just thin it up and still hold the shape nicely, and that's the kind of shape I'm looking
for, and you can take care of it easier, much easier when the clay is dry, and then just
trim and remove it.
All right, so I hope this demonstration helped, and I will show you how I do the trimming
and do the Scribbilo carving and chattering, okay.
Thanks for watching.
