What's up guys? I am grateful that you are here. Thank you for joining me today.
On the last video, we made this really cool bowstring jig. In today's video, we are going
to make a Flemish twist string while using this jig. We're going to find out all the ins and outs
and how to set it up properly. Also, we're going to see how to find the right length of bowstring
that you need for the length of bow that you have. And then also at the end, I want to give you guys
a really cool tip on the best way to serve your bowstring. So let's get right into it.
There are two main reasons we use a bowstring jig. The first one is the speed. It makes it
so much faster. We only have to measure once and that's when we set up the bowstring jig.
The rest of the times, we just move that dowel to the corresponding number and bam,
you're ready to make your bowstring. The second reason we use a bowstring jig is so that all of
our tag ends at the end are all staggered. That's what all those dowels real close together are
there for. Now you can accomplish this without a bowstring jig, but if you're going to make more
than one bowstring, I would recommend making a bowstring jig. If you made the same bowstring
jig I did, you can just use my numbers here. If yours is a different size, you're going to want
to do these calculations. So I measured out what dowel hole corresponds with what string length.
And how you do that is you want to measure from the bottom left dowel up there to the top
left dowel. And that for me was 24 inches. Now you're going to wrap the string around that side
and the other side so you need that times two. And then you're also going to go around the top
left dowel and the top middle dowel and that's going to be times two as well. You're going to
add all those numbers together and that's going to give you the length of strands you're going to
get for that first dowel hole. And now that we've got the length of the strands, we need to figure
out how long of a bowstring this will actually make. Here I have 58 inches on my strands and so
the numbers we need to do is we need a negative 17 inches from the full strand length. How that
breaks down is 8 inches on both loops. So 8 minus 8 and then we're going to negative another one
inch for the twist we're going to put into the string. So my bundle of 58 strands is going to
turn out for me a 51 inch bowstring. So to make it simple, all you have to do is minus 17 inches
off of the total length of your strands and that'll be the size of bowstring you will get
in the end. And for my bowstring jig, I've got the adjustment dowel rods one inch apart.
This means that it's going to add two inches to each string each hole I go back. So my first hole
is 41 inches. You can see here I did the math and the second hole is going to be 43 inches.
The next one's going to be 45, 47, 49 and so on. And if the length of bowstring you need does not
fall exactly where one of these dowel holes is, it's no problem at all. It's extremely easy to
remedy so I'm going to show you that here in a minute. Now the bowstring jig that we made in the
last video goes from 41 inches all the way up to a 71 inches. So this is going to cover nearly every
single bow that you might possibly have or want to make. Now take a deep breath because that's
the only math you have to do and you'll never have to do it again now that your bowstring jig
is set up. We now need to figure out what length of string you need. Now whether you made your own
this process works the exact same. You're going to measure from knock point to knock point and
then you're going to subtract three inches from that amount and that's going to get you to the
amount you need. In my case I needed a 56 inch string. Now I did not have a dowel hole for that
so if your string falls on a half inch or on an inch that you do not have a dowel hole for, just
go to the nearest dowel hole that is larger. You don't want to make it smaller but you can make it
larger and it will be really easy to end up with the correct length of string that you want.
Today we are making a 12 strand string which is probably the most common. It pretty much
fits all common knock sizes and that's kind of why you want that thickness of the string.
So how we're going to accomplish that is we're going to make two bundles of six and twist those
together to get our 12 strand string and the string board is used to quickly form these two
bundles of six strands. I started by tying the string off on the bottom left dowel and I wrap
it until I have six strands. Now you will count seven strings going across the middle here and
that will mean you've got six strands. Trust me, just count them. And the next step is to cut the
strands right up in between the middle of those dowels. This is what gives us that staggering
effect and gives us an awesome taper off of the loops that we're going to make. Now all you've
got to do is repeat this process a second time and then you'll have your two bundles of six
strands. In order to keep your strands together you're going to want to use some wax. Now you
don't want to use just any bow string wax, you're going to use bow makers wax. I believe it has much
higher beeswax in it and it's activated by heat. So as you rub your hand along the string it makes
all six of those strands stick together really well and makes the bow string making process
much easier. Continue this process for your second strand of six. I personally like to use a different
color because I think it gives the string really nice contrast but it's completely unnecessary.
You can use one solid color or 12 different colors, really whatever you want. Another thing
you're going to want to gather while making your bow string is some clamps or little alligator
clips, clothes pins, paper clips, whatever it is just to hold the bow string in place as you twist
it. It makes life so much easier. I use the dowel holes up the middle as my measuring tape since I
know each dowel hole is one inch apart. It makes it really easy. So I measure out eight holes so
that I can have eight inches to start my first loop and that's where I put my clamp. And now it
is time to start our Flemish twist. It's actually very simple. All you have to do is twist the string
to the right and then pull it over the top, twist the next string to the right, pull it over the top
and so you're twisting the strands in one direction but twisting the bundle of strands in the opposite
direction and this is what makes the awesome Flemish twist string. The size of the loop you
end up making is going to be completely dependent on the size of the nocks on your bow. For most
long bows, two inches is a good starting point for the size of the nock loop, especially for the
bottom loop because the bottom loop we're going to make is going to definitely be smaller than the top
because that one stays there all the time but the top loop we slide up and down when we string the
bow. So I'll make the bottom loop about two inches and then the top loop I'm going to make about
three. Once you've got the string long enough for the loop size you want, it's time to twist it
together. I put the green on green and the black on black but it doesn't really matter. The idea
is that you join the strings and you start the Flemish twist to make the loop and so twist the
strands to the right, bring the whole string over the top and you continue that down until you are
past all your strings. This is where that taper comes into play. It's really nice that it slowly
tapers out the thickness of your string. Once you get past all of the tag ends of your string,
I do an extra 10 twist, hard twist, just to make sure that it holds tight there. At this point,
it's a good idea to put your loop over something solid and give it a really good tug. This will set
all those twists in and keep it from unraveling. Now that completes the first loop and this bow
string is looking awesome but we got a little problem we have to fix. Since we twisted the
string, the rest of the string has twist in it so we've got to even that out and twist it back to
straight but we got to go beyond straight so that when we make the second loop the strings end up
straight and so this is called back twist and this is not something you want to miss while you're
making your bow string. You normally need to put in about 20 twists of back twist and that'll be
good for about every string loop that's eight inches long. In order to untwist your string,
just start up by the clamp and do one bundle at a time and work your way back until it's all
straight and then when you get back to the end, you can just twist it up 20 times and you should
be good to start on your second loop. In order to find where you need to start your second loop,
measure your string out to where you want your finished distance and then add half an inch and
put the clamp right there and that's where you should start your second loop. Then repeat the
process as you did on the first loop, just remember you might want to make this loop a little bit
bigger than the first one for the top limb. Alright, we are almost done with this string.
I just trim up some of the tag ends and then I twist the full string just to give it a little
bit of twist and then I check my distance. When we started, we set out to get a 56 inch string
and it looks like we nailed it. Now, if your string does not come out exactly where you want it,
all you've got to do is twist the string tighter to make it shorter or opposite, twist the string
a little looser to make the string longer and it should be close enough that you can get the string
length you want. The very last step is to rub some bow string wax all along the whole string
and just rub your hand on there so the wax melts into the string and it'll make it one cohesive
unit. Then to string your bow, throw the big string over the top loop first and then the little string
on the bottom loop and then you can go ahead put your hand on the handle, slide it up and boom,
there you go, a strong bow. That's all there is to it to make an awesome Flemish Twist
Bow String. Now, all we've got left is to put the serving on. You're going to want to start the
serving just below the handle area and work your way up past your knocking point so that the arrow
can knock on the serving and then also if the string slaps against your arm, it'll be along
the area where the serving is rather than just the bare string. Pull out about an inch and a half of
serving and point it towards the direction of the arrow rest and then what you're going to do is
you're going to wrap over top of that piece of serving all the way up until you get past the
arrow rest area and then you're going to make a big loop and pass the serving through that 15 times
and after that serving is passed through your big loop 15 times, you're going to bring that back
over top of the serving you already did. Then as you continue to serve the string, it's going to
unwind the string you just passed through the loop and it's going to become a knotless knot
and so once it's all the way round up, just pull the extra string through and then cut it off
right there and you are done. I think this bow string turned out really good and I hope yours
does too. Thanks for watching!