Japanese woodworking - Building Winder Stairs

Shoyan Japanese Carpenter
89 followers
15 Video Views·Dec 24, 2022
Hello, this is Shoya, a Japanese carpenter.
Today, I'd like to show you how to make a staircase
in this 1.8m x 1.8m space.
This staircase has, from here,
4 steps of straight stairs,
5 steps of spiral stairs,
and 5 steps of straight stairs.
So, total 14 steps.
In this video, I'd like to show you
how to install spiral steps.
And in the next video,
I'll show you how to install straight steps.
First of all, prepare the actual scale drawing
of spiral steps.
People walk through the center of the width of steps
if it's a straight stair.
But in the case of a spiral stair,
people don't walk through the center.
They walk a little inside,
around 1 third from the inside edge.
So, draw the circle whose radius is at 1 third width
and divide it into 5 equal parts.
And decide the width of steps
to be equal to each other.
OK, now drawing is fine.
Based on this drawing,
make spiral stairs.
Before that, let me sharpen the blade of plane
to shape timber as well.
This time, the material is dried local pines.
First, shape the end surface of the materials
to make it straight
and shape it to be the same as the drawing.
One board cannot cover the shape of the spiral step.
So, connect three boards and make one step.
Put the material boards on the actual scale drawing
and trace the dimension.
Connect three boards like this
and draw the marking based on the actual scale drawing.
Cut it by circular saw.
Don't erase the marking yet this time
to adjust the shape after connecting three boards
by electrical plane.
The third board is just the same size
as cut of piece by chance.
I've never experienced like this.
This is a very rare case.
Shape the end section of the step to be straight.
Then, connect the three boards
by strong urethane glue.
This glue is quick-drying type.
So, it's necessary to fix them in a hurry.
It takes only one minute for the glue
to get hard after being applied.
So, I need to press them within one minute.
Press the boards tightly.
In this case, the shape of boards is triangle.
So, they cannot be pressed by machine.
Thus, apply pressure by screws
to fix these three boards.
OK, first step has been completed.
I'd like to make the other four steps
using the actual scale drawing as well.
The most important thing is to make
one step of three boards from the same material.
If I combine two different boards for one step,
the color will be mismatching.
So, it's necessary to make one step
from the same board
so that there is no color difference.
After glue gets dried,
remove overhanging glue and finish it.
This glue is quick-drying type.
So, timbers are fixed completely
15 to 20 minutes after applying the glue.
Gaps cannot be prevented
when three boards are fixed.
So, adjust the shape along the marking I drew first.
Make grooves on the bottom side of steps
to fix right boards.
Next, finish the boards.
This time, the each step is bigger.
So, it's a little difficult to plane.
3 to 4 days have passed
since these materials have been delivered.
So, they have gotten curved gradually.
Now, I'm trying to connect them
and make them straight.
It's really difficult work, actually.
Gloss and color are matching and beautiful
by making spiral steps using the same boards.
Lastly, cut out a groove to prevent slipping.
This blade is round shape.
So, the end of groove and the section of groove
will be also round shape.
Measure the height of the staircase
and make a scale for level reference.
Before trace a level,
confirm the horizontal line using a laser machine.
Without confirmation of the horizontal line,
the steps will not become horizontal.
So, it's necessary to confirm
the horizontal line of the floor level.
Trace a level of 5 spiral steps
from the scale until 9 steps of whole of staircase.
First of all, cut out the notches on the center column.
5 steps will be supported by the center column.
If notches are too large,
the column will be weak.
So, cut out minimum necessary portion
as much as possible.
Here is a knag where I'm trying to make a notch.
Knags of artificially dried materials become very hard.
So, if I hit such kind of knags with a chisel,
the chisel will be damaged.
So, in that case, remove the knags by drill first.
Cut out notches of the other portions as well.
OK, now I've completed all notches on each column.
Next, install substrate materials of steps.
Install the substrate materials
at the level of marking and notches.
These substrate materials will support steps.
So, I have to use strong materials.
Then, fix the steps by screws from the top side.
Without fixing them from the top side,
the steps will be curved.
So, make sure to fix strong substrate materials.
Next, install steps.
I don't fix them one by one.
First, install all steps temporarily.
It's because dimension of these steps
are based on drawing only.
So, they need to be adjusted in sight.
So, first, install these 5 steps by way of trial.
And check whether there is no misalign.
Then, fix them as final.
When fixing natural woods by screws,
make a little larger pilot holes.
So, that woods can avoid load and cracks.
These materials are made of pines.
Pines are cracked easily due wind and sunlight.
So now, I'm applying wood glue
on the hole of end sections.
By this wood glue, cracks can be prevented.
Next, install rise boards from back side.
The worst thing regarding staircase
is the crack of rise boards.
This is 50mm thick pine board.
It's the easiest to be cracked.
So, make sure to apply wood glue on the end surface
to prevent cracks.
Then, fix it by screws.
Apply wood glue on the both edges as well after fixing.
This spiral type of staircase
used to be called Nenshi-agari.
A good point of this type of staircase
is to be made in a narrow space.
This staircase I've been making today
is made of 14 steps in 1.8m by 1.8m space.
Actually, spiral staircase of 5 steps
is difficult to make.
OK, I've completed to make spiral 5 steps.
In the next video,
I'll install the straight steps
above and under the spiral steps I installed today.
That's all.
Thank you for watching my video.
