Japanese woodworking - Stile Cutting and Installation

Shoyan Japanese Carpenter
89 followers
Dec 24, 2022
Hello, this is Shoyan, a Japanese carpenter.
Today, I'll install stiles at the entrance before fixing flooring.
And at the same time, I'll install stiles in front of a wood stove also.
This space is for a wood stove.
Its size is 1.6 meters by 1.6 meters.
A wood stove will be put at the position where a fan is put now.
Put tiles on white area,
and put wooden flooring on joist area.
I'd like to install stiles to separate these two floor materials area.
As you can see, I've purchased a new saw.
I had been using an old one before,
but I couldn't cut timbers accurately by old one.
But by new one, only after fixing the angle of the saw,
I can cut timbers easily.
I'm using this comfortably, and it's very quiet,
so I can work without bothering neighborhood.
As expected, newer is better.
This stile material is a standardized product.
There was no available material that fits this portion.
So, put substrate timbers of 10mm thickness on the back side
to adjust the top level of stiles.
At this joint portion of the stiles,
make some dents by hitting with a hammer.
These dents are very small.
They're very important.
Put wood glue on these dents,
and stick the stiles to each other.
Then, gluing these dents will work as something like dowels later.
That prevents the positional shift of the stiles.
So, this joint will be sturdy.
This white portion is made of calcium silicate board.
It's something like a concrete board.
For this material, I have to change the type of glue.
So, I put urethane glue on it.
I'm using normal wood glue for the joints of stiles.
To make the glue work like a dowel,
I apply the glue more amount than necessary.
This location is just in front of a wood stove.
So, whatever material I use here,
shrinkage of members must happen,
which causes some gaps among each member.
So, to prevent that kind of problem,
fix the members sturdy as much as possible
by fixing them with glue and screws.
I drive in screws diagonally
at the time of fixing stiles from side also.
If you drive in screws diagonally into stiles,
the stiles are pulled toward inside by screws.
That prevents gaps due to shrinkage of materials.
Then, adjust the top level so that there is no level difference.
Before completion, fix them with more screws.
And just in case, drive in screws on backside also.
It was very hot on this day,
so I forgot to plane them for chamfers.
Thus, I got to modify by manual
and finish them by sandpaper after installation this time
to make a soft finish.
OK, now I've completed installation of stiles around the wood stove.
Let's install stiles at the entrance also.
The material is the same as flooring materials,
which is Japanese cypress.
Its size is 120 mm by 150 mm.
After cutting by circular saw,
shave the corner roughly.
This edge will penetrate the wall.
That's why I have to shave the corner
not to damage by hitting by the corner.
The stiles for the entrance are L-shaped,
made of connected two timbers.
The stiles will come just beside of the entrance door sash here.
It will be invisible finally after fixing the door frame.
Draw the marking by measuring with a scale.
To be honest,
I'm not good at marking on timbers using a measurement tape.
So, it's necessary to check once again
when I do marking using a measurement tape.
It's much better for me to use a scale
never to make a mistake.
OK, let's cut out joints.
There is a small conflict between the stile and the girder.
So, I cut off the end of the stile a little bit.
Cut out the top side at 45 degrees.
This portion will appear,
so cut it out by fine-tooth saw to make it good-looking.
The important point to cut timbers by manual saw
is to attach your thumb on the saw
and cut the timber little by little.
Use your thumb as god of the saw
so that you can cut it straightly
even if it's a very wide timber.
Make a vertical groove at this portion.
Its size is 15 mm by 15 mm.
OK, now the female joint is completed.
This stile will be the male joint
to fit on the previous female one.
Cut out the top side at 45 degrees as well.
The previous one was female joint,
so only vertical groove was required.
But this one is male joint,
so I have to remove a big portion by chisel
to make a tenon that will fit the groove of the female joint.
So, it takes several times
to make the male joint than the female joint.
I want 15 mm of the stile to overlap the girder,
so cut off that portion by circular saw.
The sound of flooring can be prevented
by fixing the stile on the girder directly.
OK, now both joints are completed.
It's a little difficult,
but I think you can understand
how this joint will be fixed after you see it.
So, let's connect them.
Trial fixing is done successfully.
So next, fix it tightly.
Apply wood glue just in case.
A long time ago,
we didn't use to apply wood glue
for this kind of joints, actually.
Fix it tightly by bigger screws.
We used to drive a 45-degree dowel for this joint.
By that dowel,
each timber presses against each other.
Nowadays, we can do it by screws easily.
So, screw is very useful.
Now, I've completed installation of stiles
at stop space and entrance.
In the next video,
I'd like to fix flooring.
That's all.
Thank you for watching my video.
If you like my video,
please subscribe to my channel.
