Hey everyone, welcome back to the cave.
Today I'm going to show you how I built this heat box that is right behind me.
When making bows, and specifically laminated bows, most bowyers use an epoxy called EA40.
EA40 is a clear epoxy that is really good under compression and tension, so it makes
perfect epoxy for bows.
But to cure it properly, the manufacturer recommends to have a heat box that is around
150 to 175 degrees Fahrenheit.
Another benefit of a heat box is it really speeds up the curing process quite a bit,
from 24 hours down to 6 hours.
If you're looking to make a heat box, this video will be very beneficial to you because
I drew up on SketchUp plans for this, and I think they look pretty cool.
That software is pretty awesome and it's free online, so you can download my SketchUp plans
if you want those to follow.
If you're not interested in getting that deep into the weeds, I also made a free PDF for
you guys with a cut list of every piece of wood that I cut, and also a material list.
There's quite a few little materials, things that you might forget, so if you want that
at handy, you can download that free from the description below.
If you're new to my videos, thank you for being here.
My name's Kramer.
It's a pleasure to meet you.
Now, let's get right into the build.
Here on the hinges, I put a spacer so that the front door, when it closes, will be closing
on top of this piece of plywood, hopefully providing the best seal possible to retain
the most heat on the inside of this box.
Also, due to the weak-ish half-inch plywood, I went ahead and cut some 2x4s to just put
in the corners to add a little bit more support.
I went with the half-inch plywood because it was a little cheaper than the three-quarters-inch,
although with three-quarters-inch, I doubt you would need that support, but since I'm
making a pretty big 80-inch box, I think these supports in the corners will not interfere
with anything, and they'll just help keep the box a little bit more rigid.
Before I throw this whole thing up on the wall, I'm going to go ahead and wire it in.
I've got these little, what are these called, keyless lamp holder.
We are going to put four of these up, and you can use incandescent light bulbs to heat
up this bow oven or heat box, and that should be enough, that should be sufficient in order
to get it hot enough.
We're probably shooting for in between 150 and 180 degree temperature in order to cure
the glue or epoxy within four to five hours.
All right, so I got all four wired in.
I'm going to wire it into a switch, and then I'm going to run that to the outlet so that
it will always be plugged into the outlet, but then I can switch it on and off right
here at the heat box.
But first, before I wire that all the way in, I want to try to get this up on the wall,
which is maybe going to be a little bit difficult by myself.
Last time I tried to hang a sign, it took me far too long.
Why do I do things the hardest way possible?
And this is much bigger than a sign.
No reason to play around.
Let's just get right to it.
So the heat box is 80 inches, and we've got this duct work right up here that we're going
to need to deal with.
And if I bring it under the duct work, it's going to come right here, which would be 16
inches out.
It's going to be right there.
That's really going to mess up my workspace, and I don't want to do that, so I want to
raise it up higher.
In order to raise it above this duct work, I'm going to need to move it over here to
the left a little bit from the wall.
Yes, I should be able to fit 80 inches, so I'm going to bump it up against the wall,
raise it up to there.
Maybe even a little higher than this.
I might actually just throw the heat box on top of this for a dead man to hold it, and
then I can prop it up here while I drill through the concrete and through the box into the
wall.
Yeah, that's the best option.
So that I can glue up right here on the table, and once I'm done gluing up, I can just put
it in the heat box, and then that actually gets me closer to the outlet, which our cord
is a little short, so that'll work out really good.
Yes.
Yes, yes, yes.
This is going to hold the box on this side, and then over here, that should hold the other
corner.
Hopefully, that'll hold it in place, and that's not going to fall.
Oh, you've got to be kidding me.
That easy?
Yeah, that's perfect.
Then I'm not going to ever hit the light bulbs because they're up so high.
That's why I made it so tall, because I didn't want to accidentally bump the light bulb putting
the forbs in.
It should be deep enough to put at least three forbs in at once, and there's probably not
really ever going to be a time where I'm going to be wanting to put in more than three bows
at once.
Yes.
So much better to use your brain than your ...
Moment of truth.
It's sturdy.
Time to see if I actually know anything about electrical.
Just plug this in, flip the switch, and hopefully it turns on.
Hey, that's a good feeling.
You can see that the lights are on.
That's really good news.
So the last step we've got is to insulate it, and some people say you can use just tinfoil.
I'm going to use this.
It's kind of like bubble wrap tinfoil.
I don't actually know.
Reflectix.
I'm so excited to be able to make some of these laminated bows.
The heat box is now complete.
Let me show you its features.
Here she is, and I think it turned out really well.
Here's the light switch.
Still need to get a cover, but it turns on and off.
The heat box.
This is to hold the door up.
Come over here.
All you've got to do is release the hinges.
That one came undone, and then there she is.
Got a hole drilled, pipe goes into, bring it on up, and it just holds steady there.
Flip on the light, and there we go.
We've got a heat box.
Something I wanted to make sure happened is that the insulation up here on the top will
come in contact on this bottom board, the sides, and the top, and that creates a really
good seal.
Especially with these latches that pull it tight, that keeps this box from leaking heat.
Got it deep enough that I can fit probably at least three bow forms in.
The lights are up high enough that I'm not really going to hit any light bulbs unless
I'm doing something crazy.
And there the heat box is.
I'm blessed with this shop, but the square footage isn't massive, and when you fill it
up with power tools, it fills up really quick, so I'm happy to have it mounted up on the
wall right over the gluing station.
That should make it easy and efficient and out of the way.
Thank you guys for being here.
If you need a bowstring, go to CramerAmmons.com and you can buy one there.
If you want to see more bow builds or traditional archery tips or everything traditional archery,
you're in the right place.
Hope to see you guys soon.
See you later.