How to put tip overlays on your bow the best way! Bow tip overlays, for primitive bows and traditional archery, look really good. Tip overlays also provide extra strength for the limb tip so that when using high-performance bowstrings the limb tips won't break.
Hi, my name's Cramer Ammons.
Welcome back to the cave.
It's a pleasure that you're here.
I hope by the end of this video,
you'll understand why tip overlays are important
and how to actually install them
or glue them onto your bow.
Let's get right into it.
The purpose of tip overlays is to provide extra support
to the end of the bow so that the bow limb doesn't break.
Because with today's high-performance,
low-stretch bow strings,
it puts a lot of strain on the limb tips.
For example, when a bow is shot,
both limbs are gonna snap into place at the same time.
Now, as they hit the wall, basically, you could say,
that's providing a lot of stress on the end of the tip limb.
And if your string doesn't stretch much,
it's gonna cause more force on the tip.
And that's why I want tip overlays
so it doesn't break the tip of your bow.
If you're using Dacron, B55, D97 bow string material,
none of those will need tip overlays.
But anything fast fly, X99, Spectra, Dyneema,
anything like that is definitely going to need tip overlays.
So I'm gonna show you how to put on tip overlays today.
So with the more stretch bow strings,
the reason we don't all just shoot them
is because they're a lot slower.
And when you have a slower bow string,
your arrow arcs a lot more in the air,
which makes it harder to shoot if you're shooting gap
or, I guess, any method you're shooting.
So it's nice to have a flatter trajectory arrow.
It's a lot easier to shoot that way.
Due to that, if you're shooting wood bows,
even on fiberglass bows,
they have fiberglass tip overlays normally,
or a mix between fiberglass and wood.
Tip overlays are important
so that your bow doesn't blow up on you.
If you make bows like me, it's a good idea,
if you don't have a tip overlay,
to not cut into the back of the bow.
I've got an Osage bow here,
and there is no string groove on the back of the bow
because that would just thin it down too much,
and then also it'd be violating those growth rings,
which could make the bow weak in that spot,
causing failure.
So that's another benefit to having tip overlays
is that you can cut in the back of that string groove,
and that gives a string a very secure, solid place to go.
The exception to that is the pallet wood tie bow we made
not too long ago.
We did a mogul bat style bow.
What that means is that both limb tips are completely static.
It doesn't move at all when you pull back the bow.
It's super thick.
On those type of bows,
you can cut into the back of that static limb,
and that's gonna be okay
because it's not moving in the first place.
Material is mainly personal preference
when doing tip overlays.
Normally, it's often for aesthetic look.
The one rule is you do not wanna put a tip overlay weaker
than the bow wood or the wood you're using or the material.
You want that tip overlay to be the same wood,
equal or stronger than the actual bow itself.
As a flyby overview of how to put tip overlays on,
the goal is to get the bow completely flat
and another piece of wood completely flat
and glue them together,
and that's as simple as it gets.
There's a couple things, though,
that if you don't do or you forget to do,
you have high chance of failing,
so let's get right into it.
Today, we're gonna put on this Osage bow some Ipe,
some really hard, dense Brazilian walnut,
as they often call it, onto the back of here.
I'm gonna cut this down to a couple strips,
and then we'll get them smooth.
The easiest and fastest way to flatten the tip of your bow
is gonna be with a belt sander.
You can definitely do it by hand,
but if you do it by a belt sander,
it's gonna save you tons of time.
We've got these flat.
They mate together perfectly, and there's no gaps.
I can't see between it, and that's the goal.
You do not wanna see between there.
If you see any ridges in it,
stop and get it flat before you continue,
because there's three things that are very important
when doing tip overlays.
The first one is that it's completely flat.
Secondly, you wanna scratch up the backside
so there's more gluing surface.
Do this with a pocket knife or a hacksaw blade.
The third thing is to clean it with acetone.
Don't overlook this step.
Making sure all the oil is from your hands
or anything is out of the wood is very important
in order to make the lamination stronger than the wood.
Lastly is glue.
What kind of glue should you use?
You can use whatever you really want to use.
A lot of people use CA glue.
There is a Bowyer CA glue I've seen that is really thick,
and it takes a little bit longer to dry.
I don't know quite the difference in that
than just normal super glue, but I've never used that.
I have used Titebond wood glue.
I have used Smooth-On EA40.
I know you can also use Titebond's Hive glue.
That sort of thing would work just fine.
But what's really more important than all of that
is the preparation, making sure it's flat
and making sure that it's completely clean and scuffed up,
and then you clamp it down.
You don't really have to put a lot of pressure.
Just a spring clamp works great, and you'll be good to go.
See how much comes off that?
Today, I'm just gonna use wood glue.
Couple spring clamps should be plenty
of clamping pressure for this.
Let it dry, and then we can shape it.
And if you wanna get an awesome, contrasty layer look
with a dark and a light wood,
I would suggest to go ahead and glue them up
in a big block like this,
and then you can break them down into your tip overlays,
and that's much easier than gluing this small piece up.
I've tried to glue, see, this is, what,
one, two, three, four laminations.
I've tried to glue four laminations onto the bow
at the same time, and all these pieces
just slide around so much.
It just makes it so much easier to do it in two steps,
and then you can have a ton of tip overlays all at once.
An inch and a half long, just over half an inch thick,
and then the width depends on the bow I'm making.
This one's just gonna be right over half an inch as well.
If you're doing a handle section,
the steps are gonna be the exact same
as it's gonna be for the tip overlays.
I'm gluing up the handle section on this bow,
so I'll glue up the tip overlays here as well.
First thing is to get it flat.
Secondly, scratch it up in random directions.
Lastly, acetone it.
This time, I'm gonna use Smooth-On EA-40.
That's actually my favorite glue now,
and I find it to work the best for pretty much everything.
All right, it's time to shape this.
I've been using this little dremel tool,
and it works really good with a flap disc on it
to sand it down real good instead of hand sanding it,
but I've made plenty of bows hand sanding,
so it's not necessary, but it is very useful.
Can clean this off real quick.
See it come alive.
That's pretty much all there is to making tip overlays.
I'm gonna go ahead and show you
how I cut my string grooves in on this other bow.
The glue-up is done.
I'm gonna show you how I do tip overlays.
First thing is I mark half an inch.
Make it darker with a pencil.
All this can be done with hand tools,
but I'm gonna use some power tools
just for the aspect of speed.
Cut a groove the depth of the string.
That should be good.
Flip it on its side.
I'm gonna grab a square and do a 45-degree angle.
If your tip is a reflex,
you're gonna wanna adjust accordingly.
This is a part people forget all the time.
When the string is at brace height,
it's about that 45-degree angle,
but when it's drawn, it moves like this.
So there is some movement,
and a lot of people don't account for that,
and it makes the string kind of bend like so.
So in order to account for that,
when it comes out to about there,
it's gonna be like so.
And so the groove isn't just gonna be one groove.
It's going to start small and then be wide at the bottom,
so that it allows for that string to move back and forth.
It's getting deep enough in order to hit the other line.
I'll just grab a hacksaw,
clear out the excess material with a utility knife.
We'll flip this over and square across
from the belly of the bow.
From those two lines,
we'll be able to connect the two lines in the belly
to either side of the groove on the back,
and that'll show us the exact depth.
You want those to be exactly equal on both sides,
so you don't have any unnecessary limb twist.
I cut the groove in the side,
the depth of my bowstring as well.
So I just check it with the bowstring.
It's a little proud.
Take it down a bit.
Then you should be good to go.
From this point on,
it's personal preference on how you wanna shape it.
You could shoot it just like this.
Clearly, it doesn't look good.
If we're going through all the trouble,
we're gonna make it look good.
So I'm gonna round it to a shape that I like.
Next, I use the orbital sander
to get it just more round, more smooth,
and take off a little more material.
A Dremel tool with a flap disc does a real good job
to clean up all the marks from the orbital sander.
Next, it's time to finish up with hand sanding.
When you're working on the grooves,
you can grab your chainsaw file
and wrap your really fine grit sandpaper in it
to clean up the grooves a lot better.
The best you can, you wanna sand with the grain of the wood,
and that'll help you get a better finish.
These tip overlays are fairly thick,
and these are the half-inch ones I did.
So if you want smaller tip overlays,
you can just use less laminations,
less thickness of wood, and it should be okay.
I probably wouldn't, for a wood bow, though,
go under a quarter of an inch.
It is based upon your material, though.
If you're using horn or something really hard,
you can use smaller tip overlays,
and you'll be completely fine with it.
And that's pretty much all there is to the tip overlay.
Clean it up here so you can see it a little better.
I'll put the finish on the tip overlay
when I put the finish on the rest of the bow,
and then clearly you can sand it as much as you want.
I haven't even got all the sand marks out on this.
But for demonstration, that's how it turned out.
I hope this video was of some benefit to you.
Thank you guys for subscribing.
Everybody who's here blows my mind.
Like, seriously, I can't thank you guys enough.
I hope I'm able to add a little bit of value
or knowledge from my experience to you guys.
If you want more from me, you can subscribe.
Also, if you're interested in a bowstring,
maybe a tillering bowstring if you're making bows,
or in bows, you're gonna wanna check out
KramerAmmons.com.
That's where I sell all my products.
And I'll announce things on YouTube and Instagram
if you wanna keep up to date to let you know
when I'm gonna be selling some new bows.
Thanks for being here.
You guys are awesome.
It's been a pleasure to talk to you.
Have a great day.
Stay positive.
Smile.
We'll see you later.