Spray paint is simple, effective, and affordable. Just about anyone can use spray paint and get good results - right? Well - not so fast! If you want PROFESSIONAL results, there are some methods you need to use to get the finish you really like.
Buy your DFJ T-Shirt, Cap, or Coffee Mug at https.//www.dirtfarmerjay.com/shop
There are a few variables that need to be addressed to assure you get great results when spray painting or applying finishes (such as lacquer or varnish).
First, buy the best quality paints. Cheap paint runs easily and covers poorly. Cheap paint is suitable for quick color changes where it will not be scrutinized up close, or won’t be exposed to the elements. An example is spraying theatrical prop braces black. Highly quality paint covers well, resists runs, and holds up longer.
Second, spray in a sheltered place with good ventilation. You don’t want to breathe the fumes, it’s just not good for you. Also, items that have been heated up by sunlight are better painted when they are closer to room temperature. Being sheltered or in a shop environment also allows you to avoid windy or breezy conditions, allowing for more consistent application. Insects are also greatly diminished, which seem to find their way right away to freshly finished surfaces!
Third, protect the surrounding area from overspray using draping, backdrops, or shields. We use old corrugated plastic signs, sheets of cardboard, or butcher paper. It only takes a few moments, and the clean-up is really fast.
While you’re at it, you’ll get better results using “painter’s pyramids” or other sharply pointed devices that both raise the object being painted off the table, while not marring the finish when the piece is turned over to paint the back side. Raised edges also allow for better paint coverage along those narrow surfaces.
As for the application of the paint itself, there are some rules of thumb that will help you get the best results. Make sure the paint can is well shaken, and that the spray head is clear. Try to paint surfaces that are horizontal. This allows the paint to even out better and resist drooling. If you do need to paint on vertical or upside-down surfaces, do so with multiple light coats.
We’ve saved the best for last. There are two “pro” tips that will give you a beautiful finish. First, start the spray just before you move the spray across the surface. This allows the rate and pattern of the spray to stabilize before being applied. And, stop the spray just a split second after going past the surface. Again, consistent application from side to side is key.
Second, keep the distance between the spray can and the object being finished the same by using a parallel motion. A common mistake is to arc your arm back and forth. This means the edges will get less and the middle will get a lot - and will be prone to running. Not good.
Resist the temptation to test the surface by touching it. Let it dry well. Humid weather will take longer. Do any touch-ups sparingly.
And, remember, if you do have to paint vertically or up into a surface, do so with light, multiple coats. Heavy spray is NOT a shortcut, because you’ll have runs and areas you’ll need to repair. Save yourself the headache and do a light coat several times.
Sure, you can go get decorative items painted, but why? JUST DO IT YOURSELF!
Buy your DFJ T-Shirt, Cap, or Coffee Mug at https.//www.dirtfarmerjay.com/shop
Follow us on Social Media to know when we’re building projects or releasing new episodes!
Hey, Dirt Farmer Jay here from DirtFarmerJay.com. Spray paint is a great way to get color, a beautiful
finish. If you know how to do it right, let me walk you through it and I'll show you a few tricks
that'll get you the results that you want. Hey, Dirt Farmer Jay here from DirtFarmerJay.com. You've
got a project that you want to spray paint, give it a great finish, some beautiful color, pop, or
perhaps it's a finish that you're spraying to do a piece of furniture. Well, there's a few things
you need to know to get the results that you really want on your project. Let's start with
the product itself. Now, we're talking spray paints here and it doesn't matter if it's Krylon,
Valspar, Rust-Oleum. Some general observations. Number one, buy the best paint you can afford.
Now, these inexpensive touch-up paints like these, these are like under $2, up to $3. These are great
for quick theatrical prop touch-ups. I remember one product or project that we were on where we
had a black industrial ceiling. We were hanging some light fixers or theatrical lights and we
needed to touch up the areas that we drilled or chains we put in. This kind of paint's great for
that. Nobody ever comes close to it. There's no abrasion on it and nobody's inspecting it. So,
this is a good use of that, but for everything else where it's going to be exposed every day,
wear and tear in the site or where other people are going to walk by and see it,
go and invest in a little bit more better paint. This paint here runs probably between $5 and $10
a can, depending on where you buy it. Now, when you get a can of paint, the first thing you want
to do is shake it really good. And in this case, you can hear the agitator because I have been,
and it's a marble, and you shake this for a long time to get all of the pigment, the solvents,
the propellant, everything all well mixed together to give you the results you want.
Here's a can that's been sitting for a while and you can hear it. It's not. There it goes. It
finally broke loose. And so, I'm going to have to spend some time shaking this or hand it to
somebody that doesn't know any better to spend some time shaking this for a long time to get it
ready to use. So, those are a couple things you've got to keep in mind. Third one is the environment
in which you paint. If at all possible, move indoors with good ventilation. Yeah, you can
get high from the spray off of these, whether it's lacquer or it's a varnish or it's spray paint,
and nobody got time for that. You don't need to do that. Open ventilation, but try not to get too
much breeze. You put this outside and it seems like not only is it hard to direct the spray and
get it to land where you want it to, but every insect for miles around decides to visit and land
in your freshly painted project. So, inside is much better. Next, create an environment where
painting makes sense. So, if you look here, what we've done is put down masking on our work table
because we are going to get over spray. And so, if you need to, I actually put a backdrop if we're
going to get a little bit of spray going past it. I don't want that all over my project table
or all over my floor or other items in the shop. So, put down a little bit of protection. If you
need a mask, do all that. But in other words, do the prep work that's required and that'll pay
dividends at the end. The next thing to keep in mind is the orientation of the workpiece. If at
all possible, paint it flat like this instead of vertical like this. Now, sometimes you're going to
have to paint it vertically if it's a large object or it's more convenient to do so or it's got lots
of dimensions on it. And if you're going to paint vertically like this, light coats, multiple coats,
will give you the results you want. If you put heavy coats, you're asking for trouble because
if you get too much paint, it'll drool or sag and ruin the finish and you'll be back to scraping
it off and starting all over. So, if you can, spray horizontally. Now, related to that, when you
something like this horizontally, and we're just going to spray paint this right here,
the edges can really cause a problem because when you spray along the edges and if it pools up,
then it can grab onto the masking material in the background and cause a deformity on the edge of
the piece. And pieces of MDF and certain lumber products are going to be thirstier. It's going to
soak up more finish, whether it's a clear finish or a paint finish, than the flat surface, which
seems to be harder milled. So, how you overcome that is use some kind of lifting device. And what
we're going to do here is just use what's called a painter's point. These are little pyramids. You
can buy them as sets. They're very inexpensive. And these are real sharp points that allow you
to paint and then flip over and have just points that you can touch later. So, when I set that on
there, now I have this nice platform with space around the edge. And we're going to go ahead and
paint this. We've shaken this for several minutes here. It's ready to go. And what we're going to do,
here's the next tip. This is really important. You don't aim over the top and start spraying. You
always start the spray at the edge or beyond the edge of the object and go past and release. Never
start and stop over the object. So, it looks like this. I'm going to start over here, move across.
See there? And I'm going to move across in bands. Notice that I'm painting right before and after.
And I get a more even coat across the surface as I go. Now, because it is laid horizontally,
if I do have a thick spot, what's going to happen is the paint's going to tend to level out.
And instead of pooling, it'll end up laying across there. We've got a very nice finish there.
Nice, clean finish. Now, the edges need to be painted as well. And because they're elevated,
now I can go along the edge. Again, start and stop. Before and after. Like that. And then go
all the way around and get this beautiful finish. And now we'll just cut over here, too. A little
reach a little over here. Again, notice my habit. I always start and stop before and after the object.
And we're going to hit it one more time because it sucked it in on the top. And again, because
it's laying horizontal, very low chance of any drool. We'll let that dry and that's going to be
a beautiful piece. Very solid. Let's look at what happens when you do spray vertically and how to
control that. All right, let's look at doing something vertical. Now, I've tilted this little
piece of MDF against a paint can. It's pretty vertical. It's close enough. Let me tell you what
not to do and what is a common rookie mistake. Let's move you from being an amateur to professional
when it comes to applying these finishes. This is a typical way someone will apply paint. Whether
they start in the middle or on the edge, they'll tend to do this arc type of thing. Pivoting from
the elbow. And so what you're doing is arcing back and forth. Here's the problem. When you're at the
arc over here, the nozzle is further away from the piece. Here to here. When I arc in, I'm closer.
And when I arc to the right, I'm further away. Meaning as I apply the finish doing this arc
motion, the middle third is going to get a lot more finish. You're going to get build up and
there's where that drool happens again. How do you eliminate that? You don't arc. You move parallel
like this. Again, start before. Travel across. Let go as you exit. Back and forth. Going straight. Not
that. This. Back and forth. Also, when it's vertical, don't apply heavy coats. Come back
multiple times to get the finish you desire. Well, let's go ahead and take it on. We'll take this look
at this piece of MDF. Here we go. Starting before. Off. Straight. Back and forth. Look for any places
that you felt were light. And again, we're just back and forth straight. And I'm going to quit
about right there. Because I think we've got enough finish on it. Looking down here, yes. To let it sit
and dry for a bit. Now, I want you to notice another thing that happened here. And that is
the amount of overspray that does occur. And why it really makes a difference to use masking paper,
to mask. Even that top of that can of paint right there got hit. But having a backdrop to keep this
overspray off of everything else. Now, even there, I can see it's flashing and drying off a little
bit. You'll see the color or the sheen change. So, I'm going to put a little bit more on it.
Just to even it out. And on this, you have to do the edges up on the top. Going at an angle
as we did on the other one. But let's take a look and see what that looks like now that we did that.
And you can see here we have this really nice even. There's a couple places that
are slightly thinner. But again, a beautiful finish. One to be proud of. Don't use the arc.
Straight parallel shots. All right. There's a couple other things you should know. Okay. Let's talk
about painting metal. When you paint metal, the surface is not absorbent. So, when you spray paint
it, it's not going to soak any end. Therefore, the paint is going to be more prone to drooling.
And so, it does take usually multiple light coats to get the finish you require.
Again, if you can do it horizontally, much better to do so. Start and stop as you exit off. And then
get the coat that you want. One other thing. If you're using a dark paint on a light surface or
a light paint on a dark surface, it's especially going to take more coats to get the color to be
true and not have any of the base color of the object that you're painting shining through. Well,
let's see what we get here. Again, now you know the drill. We're going to start further and end
further. And we're going to spray parallel, not arc. So, here we go. We're overlapping, over spraying
what you've already sprayed on what's called the wet edge. And there we have that direction. Let's
go ahead and turn it around this way. So, now that can spray the surfaces that were away from me.
And here we go again. And there you go. Beautifully painted. That'll dry. And it'll be a beautiful
piece for whatever we're making. Perhaps a little birdhouse or something. All right. There's one more
thing you should know. Before we go, that last tip. Hey, check out our website at DirtFarmerJ.com
for blogs, extended content, special offers, and our merchandise. You can go to DirtFarmerJ.com
forward slash shop. Check out our hats, our shirts, our coffee mugs. And if you're finding this video
to be helpful, why don't you like it? And better yet, subscribe to our channel. And when you do,
ring the bell so that you'll be notified every week of the latest episode for the home,
the garden, and the shop. All right. Back to the tip that we're going to give for the final
insight on this. If you're painting raw wood or these types of things, these tend to be
very thirsty. So, what we're going to do is go ahead and set up our painter's pyramids again.
All right. Now, we've got our elevated workpiece. And we're going to see what happens here. If I
spray on the end, it'll thin out in a moment here because it's very thirsty. It's like a lot
of little straws. So, I'm going to let that go ahead and soak that in. I'm going to come down
and spray the other end as well. And then I'll work around the edges. I'm just going to spray
again. Notice that parallel spray that's occurring. I'm not going to do the back edge so I don't get
between you and the camera here. But again, notice I'm doing the overlapping spray, no arc,
all parallel spray. And this looks like it really covered it well. But the reality is,
give it a few minutes. And you can actually come up close here. You'll see that it's already sucking
in the paint in the knots and where the wild grain is. So, this will not be the finished coat.
And the end is thinned out where you can see it sucked in the paint. So, we're going to let this
seal up before we give it a second and perhaps a third coat to get the desired results.
Hey, and if you like this, here's another video you should check out where we did a really great
metal flagpole, our DIY flagpole, to put out the flag on the 4th of July or other special events
for other special occasions. Check it out right there. And then also, check out this other video
that we've created that we and YouTube thinks is perfect for you. So, how do we do? Until the next
time, this is Dirt Farmer Jay from DirtFarmerJay.com.