Japanese Woodworking - Three Step Winder Stairs [Season 2 - Part 5]

Shoyan Japanese Carpenter
89 followers
20 Video Views·Dec 19, 2022
Hello, Shuin here. I'm a Japanese carpenter.
I'll now start building the staircase and divide the video into two parts.
The staircase will start with a straight stair that goes up 6 steps.
The next will be a winder stair with 3 fan-shaped steps,
and then 4 straight steps above it, making 14 steps to the second floor.
I'll start with making the 3 fan-shaped steps for the winder part.
First, I'll cut and plane the stair material.
This is my third video of building a staircase.
All 3 times, the material has been the same local pine wood.
Depending on the company and region,
pine wood is the best material for conventional construction in my area.
This is a usual scene of wood cutting.
It looks like there are quite a lot of materials in stock.
The lumberyard is shipping me extra material.
Nowadays, very few pine trees have a large hardwood portion,
so it depends a lot to get them.
This is because the logs are getting smaller,
and the trees are not as old as they once were.
The hardwood portion is large when the tree is old,
even if the log is not thick.
The pine wood was cut into a square in the log center during lumbering.
Edges were cut large at the time and dried up for about 2 years.
I'm using them as stair materials this time.
Since I've processed the staircase material, I transport it using my car.
Lumberyard delivers the materials to the workshop,
and delivers the cut materials to the job site.
However, I haven't had the lumberyard deliver any building materials until now.
I do this because I don't want other people to touch the materials
that I've finished by myself.
Well, it's hard to transport them by myself.
I've delivered the material to the job site,
so I'll begin building the stairs.
Before that, I hadn't installed the staircase's support column.
So, I'll measure the position of the steps on the top 4 steps
and the tile around the wood stove to determine the column's position.
Then, I'll draw the full-scale drawing based on the position of the column.
It's 3 steps in the shape of a fan, which will be the winder.
I'm drawing the size and placement of the triangles on the winder in full scale.
This can be calculated.
I'll use this to make the threads.
There are no rules for drawing the full-scale of the 3-triangle thread.
Because people will walk 30 to 40 cm from a column,
draw a circle in the area
and divide the same dimension into 3 equal parts on the circle.
That way, the place of the thread where we place our foot
will be divided into 3 equal parts.
All 3 threads will be attached to the same vertical position on the support column.
The thickness of the column,
the number of steps on top of the winder,
and the position of the bottom vary from side to side.
Therefore, even if the column is thin,
the thread's edge that attaches to the column must be 45 mm wide.
It can be difficult to make it in the same position as the vertical
when it's 45 mm,
but it's unnecessary to do so.
Now, I'll install the support column first.
I'll join the floor beam and the column with a horizontal member.
I'm cutting a notch into that part.
I'll use a horizontal member to join them in a simple way,
so it doesn't need to be thick.
It's the same standard as the support column.
The support column is 4 m long,
but the railing wall will run diagonally downward from the second floor,
so I didn't need such a long column.
Earlier, I cut the mortise in the floor beam.
I'll cut a tenon with minor adjustments
based on the placement of the mortise in the column that I measured.
I'll cut a 50 mm notch into the horizontal member and column joint.
It's a simple insertion joint.
I'll cut the 50 mm, attach, and secure them.
As this column will only support three fan-shaped threads,
I made it as thin as possible.
I'll install the railing wall directly to this column later
and make it as thin as possible.
I'll install the support column.
I'll measure the vertical dimension of the column firmly
and place it temporarily.
Then, measure the dimensions of the horizontal member.
I'll attach the horizontal member and secure it with screws.
I may remove the horizontal member later
when installing straight steps above it.
If I secure it only with screws, I can remove it later.
I replaced the 30-year-old laser.
This is a blue-green laser.
The full line will be displayed both vertically and horizontally.
The one I've been using was also made by Tajima.
However, since I've been using it for 30 years,
the line was fading.
It wasn't broken, but I've decided to buy a new one.
Unlike the red line, I can see it clearly.
I'll check the level of the stairs with a laser.
Because I only saw the three fan-shaped steps in the middle,
checking the level is important.
Next, I'll install the winder turret on the column
based on the laser line.
I'll make the markings on the support column
using the full-scale drawing I showed earlier.
I don't hesitate and cut off 15mm even though the column is thin.
Also, cut a 15mm notch into the columns and the studs on the wall.
I'll notch the column for the turrets.
Support material can be installed in this column
since the riser will be installed.
So, install the thread at 45mm width and 15mm depth
to the columns to make it sturdy.
As you can see, the column is thin,
but I'll cut off this amount and install the thread firmly.
I'll install support materials on the notch of the columns and studs.
The inner wall behind the outer wall is not so thick,
so I'll use 30mm by 120mm typical studs as a support material.
I can't install the stairs on the front of the studs
without cutting notches into them,
but the corner of the riser will be tricky to install.
Additionally, when I screw the thread from the top,
the screws come out of the inner side of the columns.
For that reason, I'll install the support material
on the wall side between the studs.
As a result, the thread will be installed on the wall side
and the boards will also have more surface to be covered.
This reduces the risk of cracking.
Now, I'll make the three threads of the winder part.
The threads' shape are still triangles,
but I'll join two or three boards and make it to a fan.
Join means sticking together,
so I'll plane both sides straight for them to stick together well.
Then, I place the thread on the full-scale drawing
I made earlier and trace it.
I cut the material 2m long.
I'll cut it to the proper length,
attach the two pieces together, and shape it.
I made it 2m when I processed the wood,
and I'm going to make two or three pieces from it.
It's all about joining together pieces from the same wood.
That is the most important thing.
By doing so, the luster and grain pattern will be the same.
I've temporarily put the two threads together.
Next, I'll attach it with glue.
The glue is a quick-drying urethane glue that I always use.
If I spread the same layer of this glue and apply pressure,
it'll harden very quickly.
However, if the overflow part gets on my hands,
it can be quite troublesome,
which is the most annoying part.
And the container.
It's made in Germany,
and the glue itself is a great product.
But they don't put much effort into the container,
so it isn't easy to use.
The first thread has been completed.
I'll make the second and third one in the same way
as the full-scale drawing.
The glue has dried completely,
so I'll cut the protruding parts with a cutter.
Since this is urethane glue,
the protruding glue will become a sponge.
I can easily cut those parts with a cutter.
Next, I'll plane it using an electric plane
according to the marks I made at first.
Since it's tough to plane it with a hand plane from the start,
I'll use an electric plane to do the job.
In the area where the riser will be attached,
I'll plane it a bit angled on the back side
to make attaching it easier.
Then, I'll cut a notch on the thread
where it overlaps the brace.
I'll chamfer the cutting to prevent it from chipping
when something hits.
Then, I'll do kiguroshi on the part
that goes into the column.
I'll temporarily install it to make sure it fits.
While temporarily installing it,
I'll also measure the actual length of the anti-slip.
I made an anti-slip surface for the stile
on the top of the staircase.
I'll also measure that length with a ruler.
I'll decide on the strongest location
and draw the actual length of it
by balancing the whole thing.
I'll make an anti-slip groove
on the top edge of the thread.
The anti-slip is simple with a round blade
and only one light groove.
Also, I can shift the position and make two grooves
I only made one.
On the back side of the thread
30 mm from the edge,
I'll cut a groove for the riser.
I'll sharpen the hand plane's blade
before finishing the thread.
The place that I'm sharpening
is on the entrance stairs.
I can use any plates to sharpen the blade.
Now, I'll finish the thread.
I've already planed the surface with a super surfacer,
but there's a difference in level when joining.
So, I'll plane it lightly to level it
and fix the place that is torn out.
The stairs are for a winder,
so their shape is tricky to plane.
I'll be careful not to damage it by tipping it over.
Pine wood is a material that is easy to plane.
When planed, the luster comes out
because it's resinous.
I've finished planing the threads.
Now, I'll install them.
First, place 3 threads to check the whole balance
and determine the position.
I'll take measurements from the surrounding columns.
After that,
I'll align the front sides of the 3 threads.
Next, I'll make a pilot hole
to prevent the wood from cracking,
then screw it firmly into place.
There are 3 threads,
so I'll install 2 risers.
Since it's fan-shaped,
it'll be a little longer than 3 shaku.
I'll widely chamfer at the front of the riser's top edge.
Before installing,
I'll apply glue firmly to both ends.
On the winder part,
there will be no stringer,
so the cut-ins of the riser
will be exposed to the air and dried.
I'll apply glue to the ends
to prevent them from cracking.
I'll use 65mm and 50mm screws to secure them.
At last, I'll apply the glue to the joint
between the risers and the threads.
Interior construction problems
usually occur at staircases.
The stairs are made of many solid materials,
so when they dry out,
they crack and squeak.
I use both screws and glue
to prevent this from happening.
At the same time,
I'll apply glue to the cut-in of the threads
and everywhere else I can.
Also, this staircase is not exposed to the sun.
It could be so for another site.
In such a case, it'll crack easily,
so I always apply glue to the cut-in
to prevent cracking.
Now, I've processed the stairs,
installed the support column,
and completed the winder.
I spent 3 full days installing it.
The next time,
I'll make 6 straight stairs,
then 4 steps to the left,
totaling 14 steps.
I'll make 2 sets of straight stairs.
That's all for today.
Thanks for watching.
