If you're a woodworker, you need a set of brad point drill bits to make clean holes in wood with no “blow-out” as the bit exits the work. We’ve found a GREAT set for the money!
We really enjoy our PowerMatic® VS2800 Drill Press - it’s a great machine! You can check out our review of it at https://youtu.be/u_n69t-FvXg
Adding the right accessories has made all the difference, including a column-mounted bit and accessory holder, and work hold-downs. Take a look for yourself at https://youtu.be/sySYvHLTM4U
When doing woodworking, avoid using standard drill bits for metal. They will do the job, but not as precisely and cleanly as tooling made for the task. For metal bits, the drill point design and geometry are optimized to drill metal. Both the way the bit is sharpened and the way it cuts lead to two common problems when drilling wood. First, the center point tends to wander unless a definite starter hole or dimple is put in place. Second, the bit tends to tear out around the exit hole, because of where the bit is cutting first as it travels (the center, not the rim). Even a good backup block doesn’t always eliminate the ragged exit.
To drill wood, a good set of brad point bits is a “must-have!” Here’s why.
First, the brad point drill has just that; a brad-point. This sharp central point assures that drill bit deflection is all but eliminated. The brad-point sticks out furthest on the “working end” of the bit. Then, the spurs at the edges of the bit stick out a bit shallower than the brad-point, so they begin cutting the hole edges smoothly, as well as help guide the bit accurately. Third, the sharpened lips shear out the remainder of the hole and move the chips back where the drill bit’s flutes carry the chips away.
This means the hole from the top side is very clean. But what about the exit hole?
Again, because of the way the bit is designed, the brad-point, followed by the edge spurs, exits the work first, shearing off the edges of the hole instead of pushing uncut wood fiber out. After you use these types of bits for your woodworking, you won’t want to go back!
Having said all that, there is a wide range of quality of bits and associated price points. If you live in the U.S. and want a very good set, made entirely in the U.S., for a VERY reasonable price (about $30 at the time of filming), then we’ve found a great solution for you.
Check out Montana Tools® X29 Brad Point Drill Bit Set. These bits are very sharp, reasonably priced, and drill VERY clean and fast. They are manufactured by Rocky Mountain Twist in Ronan, MT, USA. These bits are industrial quality. The 6 pc. set contains 1/8", 3/16", 1/4", 5/16", 3/8" & 1/2" sizes and is not offered at this time in metric sizes. The approximate metric mm equivalents, listed in the same order as the imperial sizes, are 3.175, 4.763, 6.350, 7.938, 9.525, and 12.700 millimeters. I wish they offered them in larger sizes, but this is not planned for right now.
While we haven't received the product for this episode, we are glad to pass on good information when we get it. Montana Brand Tools is offering a 10% discount when you use coupon code DFJ or use https://www.montanabrandtools.com/?ref=dirtfarmerjay
If you need to put threads into wood so you can use connectors, check out E-Z Lok® fasteners. E-Z Lok® makes a whole line of threaded inserts for metal, wood products, and wood. You can buy sets complete with the inserts, precisely-sized drill bit, and insert tool. Inserts are available by themselves as well. Visit www.ezlok.com to get more info or to purchase these great products.
Check out our reviews and installation methods at: Foolproof Threaded Insert Installation as well at
Hey, Dirt Farmer Jay here from DirtFarmerJay.com. If you do any woodworking, even a moderate amount,
you got to drill holes. And if you've been using the standard twist bit that's used
to drill metal, you're really missing out on a better tool, the Brad Point bit. Let me show you
what it is, where you can find it, why it works better, and a very economical set that we've got
a special deal for you. Stay tuned. Hey, Dirt Farmer Jay here from DirtFarmerJay.com. Thanks
for joining me in the shop today. You know, we love having a drill press and it's part of our
maker space. And we put accessories with it. And one of the best upgrades we've done along the way
is getting the right drill bits for it. But in case you're interested in this drill press,
and you want to check out Powermatic's 2800 series, this is an older one, but we'd love
this drill press. You can just check out that link here, or just go down to the description
below. We always give you more information in the description below that we're going to take
time to convey to you during the filming of the video. But you can check that out there. Also,
a tool like this really benefits by getting great accessories with it. And a couple of things that
we've added here is a little tool deck right here where our bits set in here. We've also added
hold downs and all sorts of things with this. You can check out that video right there if you'd like
also about a couple of our favorite accessories. But meanwhile, let's get right back to what we're
here today about. And that is using the right drill bit. Now, metal drill bits are set up to drill
metal. And let me show you the difference between the two. On the right here, you can see the Brad
point bit. And on the left, you can see a standard twist bit that's used for cutting metal. Both of
these are 3-eights diameter. And there's a little bit of difference between them, though. Or let's
say there's a lot of bit of difference. Because if you look at the tip of each of them, looking right
here, you can see the tip is just kind of blunt, but not really. It comes to a point, but not a sharp
point. And the cutting edges right here are right at the forefront of the drill. And that is really
a good way to do it for cutting into metal. You essentially dimple the metal, get a starter hole,
get that shape right there into that dimple, and then start to apply pressure. And then if there's
a moderate amount of drilling, a good cutting fluid or oil is applied to really help
lubricate it. And of course, the chips are lifted away by the flutes here as it comes back out of
there. And that's set up so that it cuts metal well. Now, does it cut wood? Yes, it does, but not as good as
this bit does right here. But before we go there, here's why. When this enters into the work, because
that is kind of like a blunt rounded over area, it'll tend to wander a little bit in the wood,
depending on where the grain in the wood is, and where it's hard, and where it's soft. Also, if there
wasn't a real clear or real good dimple or indent for it to start, it'll tend to go off left or right.
And because it's cutting all at the same time, there's a significant amount of pressure
being put forward like this into the work. And so, what that means is when this exits
the work on the other side, it's done its work, it's gone through, and now it's coming out the
bottom side of the work, there's a lot of pressure being put here, and it'll tend to blow out
all the sides of the hole. If you're at this video, you know exactly what I'm talking about.
Now this, the twist bit, excuse me, these are both twists, but this is a
brad point with side spurs. And let's look at the three main or four main elements of this.
Okay, first of all, notice what's sticking out the furthest, and that is the brad point itself.
It's very sharp, it's very precise, so even a moderate dimple, or even a mark on your wood
where you've done your layout, it's going to stay true, or at least have a much higher chance
of staying exactly where it needs to. The second thing to enter the wood, notice what's now sticking
out furthest after this, and that is these right here, the spurs on the side. So they create a
shearing action which cuts the periphery of the hole, but it also helps to guide and center and
keep it true. So if you're drilling, let's say at a slight angle, like that, into wood that's like this,
well then, it's going to still help it to stay on track. So here you've got, first of all,
the spur, excuse me, the brad point, the second, the spur. The third thing to enter the work is right
here, and that is the cutting lips that now shear out the interior of the hole. But the outside
edge is defined by these, and the whole bit is divided, or excuse me, guided by this point here.
Now you have the flutes along the side that pull away the chips, and notice, let's see if we can
get you a good shot right there, that the flute edges out front are proud of this. They're actually
raised a little bit. You can see the ridge right there. So these are polishing, shearing off the side
and lifting up very cleanly all of the bits down below, or all the shreds of wood that are being
ejected up as this is rotating. And so these are very, very clean, and you can see the geometry
of why it works. Now we're going to actually put these to the test and both run them through
a block of cherry, just so you can see the results, how they drill, and also the exit. And then I'm
going to tell you about a great set that we found of these that are a great price point and will
serve you well, especially if you're first getting into Brad point bits. Okay, let's go ahead and use
a 3-8 standard metal bit. I've set it to depth on my backup block. I have set it to where it'll
drill here, and I've just arbitrarily picked a point, a marked point there. Let's just see how
this does. As it goes in, because of the thickness of the bit, it doesn't look like it's
deflecting much at all. We look like we have a really nice clean hole. Let's go ahead and put
her through, and as we nearer the bottom here. Okay, so we've gone through. There's the top,
there's the bottom. So there you can see that it didn't come through real clearly,
and you can see down here my two different holes there that I moved it slightly, so it was backed
up. It should have worked. We're actually going to move it over and do it one more time. We'll use
that little dimple mark right there this time around. Let's go for it, see what we get. Taking
it through slowly. Again, you can see it does not do well on the tear out. That's because the bit,
the geometry of the bit, is pushing it all through at the same time. Let's switch up here. Okay,
now we have switched to the Brad point bit. You can see that there. We're going to go ahead and
change this around so we have a fresh puncture point through the back. I'm going to go ahead
and start by putting it just hitting near that pencil dot to see how much deflection we get.
No deflection. It's cutting very, with a lot less resistance, I can tell you that. I can fill it in
the handles. All right, let's look there. Look at that. Much cleaner. Very slight, but it's there,
just a little bit. Scraper, a little bit of sanding. Let's go ahead and move this over a
little. There's a dimple right there. Kind of locked right in there. I really like how this
feels as it enters the work. It's very, whoop, I can feel as it went right through there. Let's
take it out. I'm going to roll it over. A little bit more tear out that time when it came through,
but I think that was more the speed I did. Let's look over here versus here. See, that's some
pretty significant tear out versus there. So that Brad point bit is really cool. All right,
let's tell you where you can get these. All right, as promised, let me tell you about a great little
set I found from Montana Tools. And as you can see, there's an American emblem on that. Now,
I'm not anti-manufacturing anywhere in the world, but I do believe this, that you ought to support
the industries of the country you live in. And if you live in the United States of America,
Montana Tools, which is a subsidiary of Rocky Mountain Twist, is located north of Missoula,
Montana in a town called Ronan. And they make all of their own equipment there, use all of their own
domestic steel, and put out everything using things straight here from the United States.
And so, if you'd like to buy American-made, this is a great way to do it. Now, you don't have to
compromise on overpaying or not getting a great product, because these products are really great.
This little black oxide set, six different bits, is about $30 with a $10 flat fee shipping charge.
And you can order as many as you want. As a matter of fact, you can also go to their website,
and you'll see that link down below that points out where you can buy them in jobber sets of
approximately six sets of six or 12. And those come in longer lengths, and they're also the bright
finish, but very sharp in that they really have done a great job on this. Now, all right, what I'd
like to do now is show you some of the engineering and some of the specific features that Montana
Tools put into these X-29 bits. The first clue is the X-29 is named after Grumman's experimental
aircraft, X-29 Ford swept wing aircraft that was under consideration for adding to U.S. military
arsenals. And you'll see this in just a moment here. Let's go ahead and get this out of the wrap,
and let's walk you step by step a few things that you're really going to like. Let's go ahead and
get this out of the wrap here, and take a look here at these bits. Now, the first thing I want you to
notice is right here, there is a back cut right along that spur, and that kind of creates exactly
what we're talking about, the Ford swept wings here. And as we pointed out earlier, here you have
the brad point. The next two items that are entering into the work are the spurs. Then you
have the cutting lips right here, and then of course the flutes carry away all of the chips
that are produced while you're drilling. Another thing I want to point out is the shape on the
bottom of these. Now, these are cut so that there are flats on each of these sides, on three sides,
allowing your chuck to really grip onto those really nice and resist spinning. All right, so
now let's go ahead and take this particular set, which by the way, they only come in imperial sizes,
but there's equivalents in the descriptions down below for each of this. Let's go ahead and use
this half inch bit, and drill it through about an inch and a half, inch and a quarter of cherry,
to see how it enters the work, and how it X's as well. Let's take a look. All right, let's see what
we get here. We're going to do this a couple times here. I'm going to go ahead and turn on the drill.
Runs nice and true, and also listen to the way the bit sounds. I'm going to go ahead and enter the work.
You can hear it's got a really nice shearing. Boy, it is really ejecting the chips beautifully,
and I'm going to go ahead and back out, and then just as it gets close to the end, it's always a
good idea, or as you're going to come out the other side, to clear one more time, and then just slowly
go through the back side. All right, so let's see what we got. All right, so there is the entry
sign right there. There's the exit sign. As you can see, there is no chip out whatsoever. Let's put
up in the light for you to see it there. There is nothing there. It is beautifully done. These are so
incredibly sharp, and for the price point, what you get, I think they're a real winner. No, we're not
doing an ad for Rocky Mountain Twist or for Montana Tools, but when we find great tools, it's our pleasure
to pass them on to you. We think you're really going to like them. Check out the website below,
and what you can do is also get a great discount using the promo code that's provided in the
description below. If you need to put threads into wood so you can use connectors, such as making
jigs and fixtures or knockdown furniture, then you really got to check out threaded inserts. You can
look at our video in the description below and the end card that shows you about a foolproof
way to install those threaded connectors, or you can take a look at EZ Lock's connector system
right here, which includes both the inserts, a drill bit, and a drive tool that makes it really
foolproof to put these in. You can check out the entire video and the review on their entire
product line right here, and afterwards, go and check out DirtFarmerJ.com forward slash shop for
a great line of merchandise on hats, mugs, and shirts. Until the next time, this is Dirt Farmer
Jay from DirtFarmerJ.com.