Skip Planing Tutorial Skip Plane Flatten Reclaimed Wood How To

Jonny Builds
96 followers
Dec 13, 2022
What's up everyone?
This week I'm gonna show you how to take some old reclaimed wood, like this barn wood board
that I have here, and turn it into lumber that we can use to build a project.
Now as you can see, this board is very warped, twisted, bowed, cupped, pretty much everything
it could possibly be.
And I'm gonna show you how I take something like this, this is oak, and it's probably
somewhere between 50 to 100 years old.
I'm gonna show you how I take this and get it relatively flat, and in my case I'm using
it to build a table.
Okay, so the first thing I'm gonna do with this very twisted board is build a planer
sled.
And to do that, I'm gonna use a piece of half-inch plywood to adhere this board to the surface
so we have a flat surface to reference on the planer when we send it through.
So as you can see, this board is extremely twisted.
If we were to adhere it like this, we would end up losing a bunch of material just off
of this side.
So what we wanna do is we're gonna balance this out to where we take off equal material
from this side down from that side.
So we wanna shim it somewhere like that.
If I put a shim in on this side, it's going to help level out the opposite side.
First we'll glue the shim down, and then we'll come back and glue the board to the shim.
And I'll just keep adding shims until the board is really well secured.
Now before sending it through the planer, we're gonna find the highest side, and that's
the side we're gonna send through first, and we're gonna reference the planer off the height
of that.
So we remove the most material from that high side and not take a measurement from a shorter
side that's gonna cause it to remove too much material and bog down the planer.
Yeah.
So that's the highest side.
Okay, so we did the top side, which is actually going to be the bottom, and you can see just
how flat that is now.
You can also see that we're gonna lose a lot of material when we do what's gonna be the
top of the table, but this is an extreme case.
Something like this, you're gonna have to lose a lot of material to get it down to lumber
that you can actually work with.
So you'll lose a lot, but here, let me show you.
You still retain a lot of the character.
So the wood is just absolutely beautiful underneath, but yet we still get to see some of the rough
wood and some of the saw marks from where it was milled, and on this side as well.
Okay, well, now we'll get this off of the planer sled and run the top side through.
Okay, so we're done with that first piece, and I just wanna show you that it's relatively
flat.
It's not perfect, but with this old barn wood, you're not gonna get it perfectly smooth,
flat, dimensional like you would lumber that you would buy at the store.
But this is pretty good, and we retained enough of the thickness to make it useful for a tabletop.
But this was a very extreme piece of wood.
This was crazy twisted, and I just wanted to show that you could take that and turn
it into something that was usable.
We're gonna move on to this piece right here.
This isn't near as twisted and bowed as the other one.
There's still a little bit of a rock to it.
But all we're gonna do with this one, and we're not gonna use a planer sled, but I wanna
show you what it's like to skip plane a piece and retain as much of the character as possible
while removing some of the high spots.
Okay, the first thing I'm gonna do is get the height set on the planer to where I'm
just barely gonna take off a little bit of material on that first pass.
I just want it to maybe not even grab the whole thing.
That's what I'm looking for right there.
Right there I'm gonna take off maybe a 64th of an inch.
Each time I send it through, I'm only lowering the blades about a 64th to a 32nd of an inch.
And this ensures that I don't take it down too far.
And with this board, I ran it through until it was even while retaining much of the milling
marks.
Then I flipped it over and planed down the other side.
Now we've got the second board all skip planed, and you can see here how big of a difference
there are between the two.
When you're dealing with an extreme case like how twisted this first board was, you're gonna
lose a lot of that character.
You're gonna keep a little bit of it, and we've got a little bit of the saw marks there.
But in order to get this thing pretty flat, we lost a lot of the saw marks and a lot of
the character.
But actually, the wood underneath is really beautiful, and we retained some.
So this is still gonna look really, really good.
With this second piece, I didn't use the planer sled, and as you can see, we were able to
keep a lot of that character, the saw marks in the wood.
And then what I'm going to do now is I'm gonna come behind that, and I'm gonna sand this
down to really even it up.
I was left with these two gorgeous pieces of oak that got joined together and used in
my Parsons Table build.
Thanks for watching this one.
I really hope this helps, and stick around to hear about my new shirts that are now available.
Hey, everyone.
I'm excited to offer you guys my new shirts.
They're available over on my website for $20, free shipping on these here in the US.
And for international shipping, just shoot me an email or a DM, and we'll figure out
those additional costs.
Now these shirts are a soft, comfortable, high-quality, tri-blend shirt made by a local
business right here in Oklahoma City.
And I've got sizes going all the way up to 3X.
Just head over to my website to order your shirts now, and there's links to that down
below in the description.
And make sure you guys like, subscribe, follow on Instagram, all those things.
And we'll see you back here next time.
