How To Install A TV Wall Mount Step by Step Guide

The BeefMaster
118 followers
30 Video Views·Dec 10, 2022
Today I'm going to show you how to take a large TV monitor and hang it on a wall.
Let's get started.
I recently made another video where I set up this FlexiSpot stand-up desk
and decided that it was best to mount the TV on the wall.
To start, make sure there's enough space and remove anything that's hanging
and also check that there's an outlet in the place where you're putting a TV.
I went with the Santa Simplicity TV mount and I'll try to link a few other brands below.
To start, I'll need a pencil, stud finder, screwdriver, tape measure, a drill, and some drill bits.
Let's now unbox it and see what we're working with.
First off is a mount template and some instructions.
Next is a mounting plate to adjust the height of the TV.
These are mounting braces to help hold the TV onto the plate.
These also help stabilize the TV.
These are the bracket screws.
This is a large assortment of bolts to help fit with any brand of TV.
Then finally, we got the mounting screws that will go into the wall studs.
Finally, underneath is the wall mount itself and the extension arm.
Just holding it, it feels very firm and strong.
On the box, it claims it can support up to 60 pounds.
All right, with that out of the way, let's take a look at where we're mounting it.
We want to go directly above a plug as the plugs are connected to the wall studs.
For this example, I wanted to match the height of the TV sitting on the desk,
so I went to the bottom of the TV, which ended up being about 47 inches.
I then added an additional 8 to where the mount would sit in the middle of the TV.
My grandpa Cap always said, measure twice and cut once.
You cannot mount to drywall, you have to mount it to a stud.
So using my stud finder, I move it over until it beeps.
Starting at a height of 55 inches,
I take several measurements to understand how the stud sits against the wall.
This is a little overkill, but I wanted to show you how the stud would look beneath the wall.
I then make measurements in the center of the stud
and eyeball it to make sure it looks fairly straight.
Now that I've marked the center, I take the mounting template and line it up.
But before I make the final measurements, I want to use a level and line it up straight.
With that set, I make a final mark and use a small drill bit
to create a hole for the mounting screws.
Doing this first will make the mounting screws go in much easier.
With that complete, I can now put on the actual mount.
First take off the wire holder on the bottom, then pull back the base plate,
which then allows me to line up the holes correctly.
With those lined up, I can now put in the grabber screw and crank it down with a socket wrench.
Make sure you don't do it too tight that it cracks your sheetrock
and also make sure that the bottom is realigned before tightening it down all the way.
It's always good to take a second and remeasure to make sure that everything's lined up correctly.
It looked good, so I put in the second grabber screw and tightened it down.
I tested the brace and it was very firm, so I then put on the base plate covering.
I took a second to try out the pivot on the arm to make sure that everything was working correctly
and to get a feel of the right direction,
the elbow needed to bend for the TV to sit flat against the wall.
Now that I have that set, it's time to hook the TV to the mount.
I had to take a minute to find the right screws,
but once I did, I took out the curved arms and faced them downwards toward the middle
and tightened them down to sit flush with the TV.
Seeing that it was very firm, I then got the mounting plate and tightened it down to the braces.
There are a lot of places to screw into, so you can adjust the height as needed.
With the brace on, I can remove the screws to the bottom of the TV stand
and take it out to mount it on the wall.
I carefully slid the TV on the top notch on the arm
and took a second to look at the nice wallpaper.
Next, I had to extend the arm out, but was very careful as the TV was not yet secure.
To secure it, I lined the TV up so that it's centered and screw it down.
Make sure that it is tight as there will be a lot of pressure on this
when you tilt the TV forward and backwards.
This setup is almost complete, but first I need to show one more step.
I put in the plug and the HDMI adapter,
but I want to avoid having the cables just hang down.
To avoid that, I remove these clips and line them up with the cables and put them back on.
They are designed so that the cables can slide freely in them when I move the arm back and forth.
You'll want to give it a little slack.
If you pull it too tight, then it will pull out the plugs.
This makes the TV look much cleaner and helps avoid tripping on wires.
Now the mount is all set up and it works great.
If you want to see how I built the stand-up desk, check out my other video.
And we're done.
Thanks for watching.
Also, make sure to put your tools away as soon as you're done using them,
or your kids may try hanging their own things throughout the house.
