Upgrading My Car stereo with $20 Dual XDM16BT install DIY

C.L.S. All-IN-ONE
129 followers
8 Video Views·Dec 10, 2022
This is CLS, and today I'm going to upgrade my stereo from this.
This is a cassette player that's in my 95 motorhome, and I don't even have cassettes
anymore.
I don't know anyone who does.
There's no auxiliary input on this thing, so I just really have no use for this stereo.
So this is what I'm going to upgrade it to.
This is a $20 stereo I just purchased at Walmart, the Dual XDM-16BT.
This has Bluetooth, it can play MP3s, it's got a USB input, an auxiliary input, it's
got everything I'm looking for.
I also picked up a SCOPE stereo connector, that way I don't have to cut any of my factory
wires and I can have a nice clean install.
And to complete this job, I got a wire terminal connection set so I can connect my wires,
I got some wire strippers, and a drill.
And before I get started, I always like to disconnect the car battery, so I'm going
to disconnect the positive terminal, that way I don't have to worry about any fuses
blowing or any shorts in the wiring.
To remove your stereo, sometimes the panels are secured with screws, so you can just use
a screwdriver or your drill to remove the panels.
In other situations, your dash panels are just secured by clips.
And to remove those panels, you want to use dash pry tools, like these.
These are usually made of plastic or nylon, and they won't harm your dash when you're
prying off panels.
But for my vehicle, my stereo is mounted on the outside of the dash panel, so I have to
remove the stereo first.
This particular stereo requires a key to remove it, but I'm just going to use a couple Allen
wrenches.
I'm going to stick two Allen wrenches on one side here, right through the holes, and pop
out one side at a time.
Some stereos use a different type of key to remove it.
Instead of having a hole, you have a slot.
And chances are, your new stereo's going to have those same type of keys, so you can remove
it.
And if it doesn't have the same type of keys, a couple smaller knives will work for that
also.
So I got mine loose now, and I'm going to pull it out, but it's stuck on something.
That's probably the secure strap that's going to be located on the back of the stereo.
To get to the strap, you're either going to have to remove more dash panels, go up underneath
the dash, or in my situation, I can just lift up the dash.
But it's going to be very unlikely you have a dash that hinges like mine, and gives you
access to everything.
This is a Class A motorhome, and it's built quite a bit different than a regular car.
Wouldn't it be nice if all car dashes did this?
It makes stereo installation a lot easier.
So after lifting up my dash and looking at the back of the stereo, we can see that there's
a support strap hooked to the back of the stereo right here.
So I need to go ahead and remove this nut so the support strap can come off, but to
get to it easier, I'm going to go ahead and remove my heater controls here, then it'll
be much easier to remove the strap.
It's only secured with four screws, so it'll be really easy to remove.
Okay, I got that out of the way, so it's time to go ahead and remove the strap now.
And there's an extra ground wire that's also hooked to the back of this.
There actually used to be a CB installed in this motorhome, so they added this extra ground
wire for noise interference.
So this wire won't be necessary for my new stereo.
So I'm able to remove my stereo now.
All I need to do is unclip any wire harnesses, and unplug the antenna.
The 1980's just called, and they want their tape deck back.
So here you go.
It's all yours.
Wow.
That was really dumb.
Maybe I should just cut that out.
So I purchased this Sko stereo connector for a 1986 through 2013 Ford vehicles, but since
this is a motorhome, this stereo connector is not going to work.
On a standard vehicle that was made between these years, this connector would work just
fine.
But since this is a motorhome, they don't do anything the same.
So this connector is completely different, so the adapter I purchased will not work.
But I got a backup plan.
What I'm going to do here, is I'm going to chop off the wire harness on the existing
stereo here, and luckily, there's actually a wiring diagram for what all these wires
do.
So I can just use this for my stereo connector, and that'll save me from cutting any of my
factory wires on the vehicle.
So here's a color-coded wiring diagram on the old stereo, and it shows me exactly what
all these wires do.
So this is the old stereo, and I'm going to go ahead and cut that wire harness off.
And this will now work exactly like a stereo connector.
So now what I'm going to do is connect the old wire harness to the new wire harness and
match all these color codes.
So this is the old wire harness.
I'm going to strip all the ends of the wire about three-eighths of an inch, so I can connect
butt connectors.
If you want to learn more about wire connections, including heat-sinking, wire stripping, terminal
connections, and more, be sure to check out my DIY wiring video, and I'll post a link
up in the corner and down below.
So I got my new stereo here, and let's go ahead and take a look at it.
And you're going to notice one thing right off the bat, and that's that it's pretty small.
It's the same width as a normal stereo, but it's not as deep, and that's because it doesn't
have a CD drive.
There's still a few people out there that listen to CDs, but I'm not one of them.
I either stream music or listen to it on an SD card.
This stereo has everything I want and need for this vehicle.
It even has hands-free calling, and it's only $20.
On the back, it has RC outputs for the front and rear channels.
It's got an antenna input and your wire harness connection.
It's also got an alarm sensor on the back of this that Walmart put in for security.
To remove it, it's just a Phillips screw, and it removes easily.
And because this stereo is so small, a support strap on the back of this stereo will not
be necessary.
It'll support itself just fine in the dash.
All right, let's see what else we got inside the box here.
We got a remote, which I've never really used a remote for a car stereo.
It seems kind of silly, especially when your stereo is usually just a hand reach away.
And here's a look at the keys I was talking about earlier to remove the stereo.
And here's a look at the wire harness for the new stereo.
So I'm gonna be connecting this to the wire harness I cut off the old stereo.
So I need to match the color codes of the new wire harness to the color codes of the
old wire harness.
And there's a wiring diagram and instructions for the new wire harness, plus there's a wiring
diagram on the stereo itself that shows what each color is and what it represents.
And for any wire connections that you're not gonna use, such as a power antenna, you simply
just leave that wire unhooked.
I don't have a power antenna, so that wire's just gonna be left unhooked and insulated.
And insulated means it's either gonna be taped off or sealed off, so there's no exposed wiring
that can cause a short and cause damage to your electrical system.
And to make my wire connections, I'm just gonna use some terminal butt connections.
This is a set I purchased at Harbor Freight for under 10 bucks.
And there's a wiring diagram on the inside of this terminal set that shows what gauge
wire will work with what connection.
Basically what you want is to find a terminal connection that slides over your wire and
fits the tightest with the least amount of room left over.
For most stereo connections, a 22 through 16 gauge connection should work just fine.
So I'm gonna start with hooking the two red wires together.
Both red wires represent 12 volt power, so we're gonna join those two wires together.
So I'm gonna slide my butt connector over one side of the wire here.
Now I'm gonna go ahead and crimp it closed.
After crimping, I'm gonna pull on it and make sure it's secure.
If it pulls off, you're gonna have to redo it.
So this one's ready to go.
Now I'm gonna go ahead and join the other side here.
I'm gonna slide the wire inside the hole there.
And it usually makes it easier if you go ahead and twist in that wire, it makes it tighter.
Then it'll slide in that hole much easier.
So I'm gonna go ahead and crimp this side closed now.
And then double check it.
And the ink on both sides here, make sure you have a nice tight connection.
So this connection's done, now it's on to the next wire.
And you wanna remember, if you have wires that are the same color on each wire harness,
it doesn't mean they represent the same thing.
One could be a ground, one could be a positive, etc.
You wanna make sure to check the color codes for each wire harness
to make sure you hook these wires up correctly.
The wire I'm hooking up now is the ground wire, and both wires are the same color.
So you wanna continue to make all your stereo connections.
A standard stereo connection is gonna consist of a 12-volt power,
which is direct power to your battery,
a 12-volt ignition, which means when you turn your ignition on, you get power,
a ground wire, and your speaker connections.
Your front left and right speakers, and your rear left and right speakers.
Those are your standard connection settings.
There's some other common connections, such as your power antenna,
dimmer control, illumination control,
but for this stereo install, I'm just using the standard connections.
Now it's time to install the radio mount and cage.
This is actually the old one, so we need to remove it first.
To remove it, it's pretty simple.
I'm just gonna bend it here in the center,
and that's gonna give me better access to the tabs that I need to push back up.
I'm just gonna use a small screwdriver and bend all the tabs back up in place
so this can slide out.
There's usually tabs that secure it on the top, bottom, and sides.
Once all the tabs are bent back in place, it should pull out fairly easy.
Now it's time to install the new one.
The cage should be on your stereo already, so you need to go ahead and remove that.
There's gonna be tabs on each side
that you can either use your fingernail or a small screwdriver to slide it off.
But be careful not to pull the tabs out too far,
or your stereo won't lock into that mount and cage correctly.
If you do pull the tabs out too far, just push them back in place by hand,
and that should be just fine.
Once you have the mount and cage pushed flush with the dash,
you wanna go ahead and bend those tabs up.
You wanna bend at least three tabs on the top and bottom,
and two on each side.
So by bending these tabs up, this locks the mount and cage in place,
so your stereo stays nice and secure.
Now it's time to connect my wire harness,
and pull that through the radio opening, along with the antenna wire.
Now I'm ready to make connections to my stereo.
After making the connections, I'm gonna go ahead and slide the stereo in the hole,
but I'm not gonna push it all the way back yet, because I'm gonna test it first.
Now it's time to hook my battery back up, so I can test my new stereo.
So when testing your stereo, you wanna make sure your antenna's working correctly,
make sure you can tune into your FM stations, whatever.
You also wanna make sure your balance is correct.
Check your left and right balance, make sure the left speakers are playing on the left channel,
and the right speakers are playing on the right channel.
Also, you wanna check your fade.
Make sure when your fade control's on the rear, your rear speakers are playing,
and when the fade control's on the front, it's only your front speakers playing.
If there's any issues with any of this working correctly,
you need to double check all your wiring, and make sure your connections are proper.
Everything's working good on my stereo, so I'm gonna go ahead and push it all the way into the mounting cage,
and finish the install.
So if I ever need to remove the stereo in the future,
I just need to remove this trim plate that surrounds the stereo here,
and then stick these keys on each side of the stereo, and that'll pop right out of there.
All's I gotta do now is put my heater controls back in place, and I'm done.
Well thanks for watching, this is CLSL1.
If you wanna hear more from me, please like, and subscribe.
And if you wanna see more of my videos, just click any of these links.
