ENGINE IS IN + R34 UPDATE | The Broken Silvia [EP7]

Broken Silvia
74 followers
11 Video Views·Dec 9, 2022
In this very special Episode of Broken Silvia the car finally has an engine in it! We mainly concentrate on refurbishing used parts that go onto the RB engine. Throughout the Episode we also discuss how the RB26 ITB's were adapted to a RB25neo engine. We also throw out the ABS module along with the horrible brake lines that run across the firewall and replace it with the GKtech ABS Delete Kit. To finish off the Episode, Damjan updates the viewers on the long forgotten project 'Poor Man's GTR'.
_________________________________________
My Instagram: @broken.silvia
Contact: [email protected]
Produced by: Damjan Bradonjic
Alrighty, so welcome back to another very very special episode of Broken Silvia
where the car finally has an engine in it. To start this episode off I'll be showing you how
the engine got stripped of all its accessories, wire brushed and spray painted black with just
normal black engine enamel. Then we'll move over to these rocker covers. The rocker covers got
paint stripped back to bare metal, primed and painted. Unfortunately the thinners I used with
my paint had a weird reaction so I'm going to have to redo these covers. For the people doing
it at home I would highly recommend skipping the paint stripper stage. It's a nasty chemical,
it stinks, if you don't wear nice thick gloves it'll burn your skin, that's the word, it'll burn
your skin. So skip that stage, just get them sandblasted. Moving over to the inlet manifold.
So the inlet manifold from factory is an RB26 part and it comes very very textury. So I used
40 grit on a flap disc to knock down all the, all the, I don't know, waviness I guess you could call
it. So that was nice and flat. After that I used 80 and 120 grit on a palm sander to refine it a
bit and then this part got sent over to the powder coaters. The powder coating being nice and thick
it filled in all the scratches then it was put in the oven and now this part here looks as nice
as the rest of the intercooler piping. So without me doing much more talking I'll let the video do
its thing. So now comes the part of where the sump has to come off. I did it for a few reasons.
Reason number one is the engine hadn't been started in a very long time and I just wanted
to double check if there was any sludge in the bottom of the sump. And reason number two, it's a
lot easier to take a sump off while it's out of the car instead of in the car. Take it off quickly,
reseal it and it's good to go. So now comes the exciting part of me telling you how you can adapt
RB26 individual throttled bodies to an RB25 engine. In this case this is an RB25 Neo engine
out of an R34 GTT Skyline and we are also still using the VCT and keeping the VCT solenoid in its
factory position. So to start things off the RB25 head and the RB26 head do not share the same bolt
pattern. So to get around that is you order these plates from Otaku Garage. These plates are 20
millimeters in thickness that allow you to change the bolt patterns. So pretty much they're two
plates. So one plate is your RB25 bolt pattern then the other plate is your RB26 bolt pattern.
So that's sorted. That's issue number one. Issue number two is the VCT solenoid is going to hit
the factory water net. Pretty much you can either relocate the VCT solenoid which can be quite a
exercise. I have seen kits get sold for $400 or you could just find yourself a good fabricator
and he'll do it for less than a hundred dollars. So pretty much this water neck has to go underneath
the solenoid. Factory it would hit the solenoid so you just have to get this water neck to go
underneath the solenoid. Then the bottom water neck from factory goes up which means it hits
the bottom of the plenum. So again you're going to chop that water neck off and get it rerouted
for it to go at a lower angle so it does not hit the plenum. What else are you going to have to do?
Oh and then your factory oil cooler. Delete that. Throw it in the bin. That is rubbish anyways.
All you're going to have to do is get like a Greddy, an Aeroflow or something. Just an
oil relocation kit so you can run an external oil cooler. Also run that oil filter somewhere
where it's easily accessible and yeah because that factory oil cooler also hits the plenum.
Reasons for doing it is I don't like Greddy manifolds. I don't like Freddy manifolds.
They're quite affordable. You can get them, bolt them on and you're good to go. The manifold I do
like is the Hypertune plenum which I cannot justify paying for a car like this. So to go for
an OEM finish and to make the engine bay look nice and presentable and also the individual throttle
bodies will give you a nicer throttle response which is a bonus. So that's why for about a
thousand dollars I did this conversion. Firstly you'll see in the video what I did is I used paper
gaskets, throw them in the bin. I had to redo everything. Use metal gaskets. In my case I used
the Tomei metal inlet manifold gaskets through the RB26 side and then on the side closer to the head
I just used, I'm pretty sure it was like a Kemetic, also a metal inlet gasket and then between
the two plates I used ultra gray gasket sealer because when I spoke to the guys from Otaku
that's what they told me to use. Now I spoke to a guy that has done the same conversion from GS
Auto Works in Perth and what he said is take everything off and get the plates sandblasted.
When you get those aluminium plates sandblasted the surfaces aren't shiny anymore and they have a
nice textured finish which means the moment you start slapping gaskets on it and you put the gasket
maker through everything because it's got a bit of a texture and it's porous it's going to have
something to stick to one another and it's going to seal properly. Very very simple. I'll add more
clips so you can graphically see it. Very simple process you can do for about a thousand dollars.
Really all comes down to how much you pay for the manifold. I think I paid about $500 so yeah.
So as you guys just saw in the previous clip the hot side and the cold side are on. On the cold
side it was just purely to show you guys the process of how to do it. Everything got taken
off as you saw the plates were still shiny. Don't worry the plates got sandblasted. Then you probably
saw me use paper gaskets. Those paper gaskets went in the bin. They got replaced with the metal ones.
Everything got redone on that side. Then on this side the exhaust manifold, the back of the turbo
and the screamer pipe got sandblasted and ceramic coated. Firstly so it looks new again and secondly
to keep temperatures down in this engine bay. So to make the engine bay extra special
we deleted the abs. Is it legal? I'm not sure. Luckily these cars did come factory without abs.
Some of them this specific model my car here is a factory abs car. It did get deleted. If you ever
have to go past inspection of pits I'm sure you could use the argument of some of them did come
without abs in it if they really picked on you. But everything being so clean and looked after
I don't think I should have problems one day even though the car is still registered. But I used
the GK tech abs delete kit. It comes with four lines again just like any other GK products I've
used. Super easy to install and yeah I tucked the line under that little seal panel so it's not even
visible. These videos are purely for entertainment so I'm not going to explain to you how I set my
brakes up. Maybe I didn't do it properly so I don't want people following these videos and
getting into accidents or something. So yeah I'm just going to show you how I use some nice
rivnuts. When you go to drill the holes into your firewall you're going to take paint off it. So
what I did is I found the color match paint to this car just a little bit that I had left over
put it in a bottle cap and I just dabbed that rivnut into the paint so when it goes into the
firewall of the car and it expands that part that is bare metal from drilling is sealed up with
paint so it doesn't rust. I have seen like in my boot where the battery was where the rivnuts got
put yeah you can see it rusting around purely because it wasn't sealed up. So yeah just a bit
of dab of some paint squeeze it it'll expand yeah it's a good bit of kit. Really happy with how it
looks makes the engine bay look really clean so yeah do it. So this video is slowly coming to an
end even though the engine went in that night as you guys saw in the previous little clip
I was freaking out I was texting people that had rb swapped s14 and 15 silvias because it is the
same process they I think the chassis are either the same or very similar. Now these guys were
make the engine sit lower while in my case I'm using r33 engine cross member and engine mounts.
So when I had a look at the engine and there was no gearbox in it it was tilting past the fender
and I started freaking out because everything was fabricated everything was done all that it
needed to be done was assemble the car. Now I was like whoa what if we have to start getting things
refabricated to make the engine sit lower by no means I'm not crazy that I'm ever going to
cut this bonnet. I love the OEM look so that was just not an option for me. Luckily the next day
Danny and I came in we dummy fit this gearbox and tilt that engine back to where to where it's
supposed to sit and the bonnet was placed over the car. Super happy with how everything fits
still needs to be aligned yeah the bonnet needs to go up a bit and everything needs to be kind
of shimmed into place but now comes the big news that you've been waiting for. So the r34 skyline
project the project budget gtr the parts have been ordered the most of the parts are already in
we're still waiting on a side skirt and a right hand side quarter panel to come in from Japan.
Thank you to Abdul from Total Nissan in Cannington for making it such an easy and quick process.
He got me a good discount on the parts and he got the parts in in no time the parts literally
less than two weeks we have 80 percent of the parts to start slowly building that car. Also
thank you to Dan for allowing me to use his GTR front end to make sure everything is in place
before that radiator spot on that car gets finally welded in because as you guys saw
the car is a crash it was in a crash and the radiator spot needs to be replaced.
So yeah this video had a little bit more talking than usual I asked feedback in the previous
episode and a few of you guys said just go into a little bit more detail about what you're doing
so hopefully it wasn't too boring with me just yapping on but yeah thanks for watching if you
enjoyed the videos click the subscribe button plenty more videos on these builds skyline will
even better than this car but less money hopefully so yeah it'll be good thanks for watching
