Patterned Plywood Roll Top Cabinet _ How to make Tambour

Michael Alm
87 followers
11 Video Views·Dec 7, 2022
This video is sponsored by Rockler.
Hey everyone, welcome back to the workshop.
Michael Alm here.
So this week we're working on another pattern plywood project.
I've had this in mind for a little while now.
I really wanted to try pattern plywood tambour.
Tambour is the material that makes like roll top desks and things.
It's basically strips of wood that run along a track
and I thought that the strips of pattern plywood would be ideal for this.
So just like every other pattern plywood project we'll be starting with a glue up
and I'm just arranging my strips to see if I can get enough length.
You got to measure along the 45 degree angle to determine your length
and all I needed was about 10 inches.
So I got just enough for that and then it was time to grab some clamps and start gluing up.
So I'm using the Rockler shore foot clamps for the glue up.
I like these a lot because they're nice and stable
and they result in a super flat panel when you're done.
So when I do these glue ups I like to arrange them on a 45 degree angle
and I use a speed square just to double check that
and what this does is just maximizes the amount of material
that you're going to get out when you do the 45 degree cut later.
So I ended up getting three blanks out of that glue up
and then I can scrape down all the excess glue.
I just use a paint scraper to clean up the majority of it
and then I do some light passes with my thickness planer.
I like to only use the thickness planer if it's going along the length of the plies.
If you have plies going in alternate directions from the actual knife it can chip the blade
so use it with caution take really light passes when you do that.
Now I can make my 45 degree cut and again I'm using a speed square for this and my track saw
and with that cut I can bring it over to the table saw and make the individual strips.
Now I can prepare to cut all the strips to length.
I use my crosscut sled with a couple of stop blocks.
This first stop block is on a 45 the second one is just flat
and I've set it up so that I'm removing just barely that that wild edge on on one side
and then I'm cutting it to length on the other side.
I'm still working on figuring out the math of how much pattern plywood
gets yielded out of a certain amount of plywood
and as you can see here I didn't cut enough so it was fine.
I ended up actually not making more pattern plywood.
I had enough for the main portion of the cabinet but the roll top needs a upper section too
and so for that I just cut regular strips of baltic birch plywood three quarter by three quarter
and and then I was I was all good to go.
Each pattern plywood strip is going to get a quarter inch dado on each end
and I'm setting that at a height of three eighths.
Using a sacrificial fence on my miter gauge I can make a cut with the quarter inch dado
and then next to that cut I can add a block of wood.
This block of wood is going to function as a stop block so once I bring in the strips of wood
I just rest it right up against that stop block and then I can make cuts on either end.
Off camera I made a test track for the tambour and I'm really glad that I did this because
when I made the first cut it was obvious that it was a little bit too tight.
So what I did was I went back to the table saw raised the blade up slightly
cut the piece of tambour one more time and then I ended up with a really nice smooth fit.
With everything all set up then I could just batch out all the parts.
For the fabric glue up I needed to find a piece of scrap plywood
that was wide enough and long enough for the entire tambour.
I could then lay that out on my workbench and attach these offcut scraps from old 2x4s
down to the sides. I want to make sure that the long ones are longer than the
full glue up and the short ones are going to be the same exact size as one of the tambour pieces.
I pressed those as tight as I could into the frame and then screwed it down with some deck screws.
Once I had the glue up nice and flat I could start working on my cloth.
I'm just using a drop cloth for this nothing fancy nothing expensive
this is literally a five dollar drop cloth that I got at a hardware store and I just cut it to width.
I didn't want the fabric to run inside of the track because I
was worried that it would start to bind up after a bit so I taped that out and then I could apply
my glue. I'm just using regular wood glue here nothing special and when I lay out the fabric
I just want to get all the wrinkles out of it. I ended up using an iron on this because I think it
helps the glue set and it helps get everything nice and flat. I did end up having some issues
with the corners though so I had to relieve those because it just kept pulling up it didn't want to
sit inside of that corner so cutting relief notches that that helped a ton and then I just
ironed. I ironed for a little while probably a good I don't know 10 to 15 minutes. With that all
ironed and flat I could remove the excess drop cloth material and then I actually pulled the
frame away from the glue up. I didn't want the tambours to accidentally glue themselves together
so I actually very carefully lifted the tambour up flipped it over and then ran my hands along
each tambour strip making sure it was separated and it wasn't going to glue itself together.
The last element for the tambour glue up is the handle and I'm just basing this on the handle
that I used on my router cabinet. I like this curve and this thing's going to sit right above
the router cabinet so it just made sense. So with the handle to the right shape I could glue it up
just note when I'm I'm putting this on and the the shape that I made it it doesn't have the track
on it it is just it just sits inside of the track and once I get that secured with a couple
brad nails I let this whole panel glue up for at least 24 hours. In the meantime I can start
cutting the parts for the cabinet. These are the two cabinet sides that I'm working on here
and they're going to get a rounded top edge. This edge is a three inch radius and I already made it
on the template that I made before the one that I used to test the tambour pieces so I just trace
that out on all four corners. So for the router table I came up with this concept for for doing
the curve. I put this sort of plumb bob at the top of it so that I know exactly where the center of
the router bit is and so once I approach that curve I try and keep the the panel flat to the
fence right at that point. So I'm keeping a close eye on it taking my time and with a little bit of
practice it was good that I did that test run because I learned a lot on that and then these
went plenty smooth. Now that panel has had plenty of time to dry so I peel back that blue tape and
cut away the excess drop cloth. Now to test to see if it works. I was definitely pretty nervous about
this. I didn't know what to expect. I've never built tambour before so this was all a big
experiment but it slot in really nice and I knew that it needed to be waxed so I wasn't surprised
when it didn't move very well but I did get it to move on that track and I was super happy.
In order to reduce that friction I sanded all of the edges and then applied a liberal amount of
paste wax to the track. Needless to say it ran a lot smoother. So now it's time to figure out where
to put the shelves and I just kind of experimented with this. I'm planning on using it to store camera
gear. Idea is keeping it dust free. I need a good spot for that in the shop and yeah once I settled
on the orientation of it I could start screwing in those shelves. I pilot drilled from the
inside just to get my mark and then from the outside I actually countersunk those holes.
I started by attaching the bottom to the side and in order to hold that
in place I used this clamp it clip from Rockler. This is super handy. I'm starting to use these a
lot in the shop lately and it's just good for holding that 90 degrees while you're
screwing in that first screw. With the bottom in place I can flip the cabinet over and work on the
top. I set a clamp at the bottom of it to just hold some tension on that while I put it into
position and then screw it in place. The next step was to install the shelves and for that I just cut
a couple pieces of scrap to the correct height and then I can just press down on the shelf into
those scraps and I know that that shelf is going to end up perfectly level every single time.
The last element was to install this little block in the back and that's just a stop block to make
sure that the tambour doesn't go too far down the track. Now speaking of the tambour I decided to
reinforce that handle. After I installed it I just was worried that it wasn't going to be strong
enough so added a bit more glue a bit more of that drop cloth and then I'm ready to install
it for the last time. How awesome does that look?
So there it is the Pattern Plywood Tambour Roll Top. I'm thrilled with this thing. I'm going to
be building out the rest of it next week so stay tuned for that. If you want to watch another video
right now I've got loads of videos on Pattern Plywood a whole playlist of it and I also have
a playlist on all the shop projects I've done in here so far so go check those out and I'll catch
you next week.
