Installing fiber cement siding by yourself, tips for working alone! #455

The Kelley's Country Life
18 followers
Installing fiber cement siding by yourself, tips for working alone! #455
All right, well, good morning, everybody, and welcome back.
My name's Andrew,
and you're watching the Kelly's Country Life.
So it was absolutely beautiful sunrise this morning.
It feels great.
It's in the lower 50s, perfect working weather.
So if you watched the last episode,
I started putting in my first window,
trimming out and getting ready for hardy board siding.
So that's what today's episode's gonna be about.
I'm gonna go over some of the things
that I've learned about install.
There's quite a bit I've learned, actually.
Things that apparently I used to do wrong,
things that have changed,
and a bunch of recommendations by James Hardy.
We went over a lot of that in the last episode,
but I'll cover it again in this one
just in case people are watching,
looking to install this themselves.
And as I always say, I'm a homeowner.
I'm not a professional.
Read the comments below.
There's a lot of people that watch this channel
that are professionals that give their input.
That comment section is a great place
to go down there and learn.
Thanks for watching.
All right, so quick recap of where we are at
before we get started.
And some points that we wanna highlight.
So we have our hardy window trim around.
I just slapped a little paint on there
because the wife and I were just looking at colors yesterday
but it's gonna get painted a much different white
down the road.
So you can get like a three quarter
or one inch hardy trim.
So before you start on your siding,
you want to obviously install anything
that you need to install through the house,
windows, electrical boxes.
Then you'll actually trim around it.
And I had to space this hardy trim out with spacers
to get everything nice and level
because there is a nail strip on the window.
And if you stick the trim on there,
it just kind of wants to fall off and roll to the side.
So you get everything nice and trimmed and flushed.
You obviously wanna get your trim at your corners.
Get that installed.
Same type of trim that I'm using here.
They make it all different sizes.
And then what's really important is your first run.
A lot of people will put down a starter strip,
just a little rip of this to provide your first kick out.
Then you wanna find your spacing off the ground
for your first run of your hardy board right here.
You only wanna nail on the top inch and a quarter
because that's the provided overlap that you're gonna do.
But it's critical that you get your first piece
nice and level,
because I'm gonna show you some hangers today that I use.
And we're gonna start hanging and just going to town,
knocking this stuff out.
So it's critical you spend the time to get your first run
as level as you can.
Now, what else?
Now, one other thing that's critical.
Anytime you have a flat transition like this,
James Hardy recommends that you put Z flashing in.
You can get this at any hardware store,
but they do not like lap siding to come down
to say their trim, a flat surface that can build up on water.
So they won't, you see, I got some lip spin up here.
They want that lap siding to be a quarter inch
off of Z flashing right here.
So water can hit, drain off,
and you can actually get air back up
underneath the siding to keep it dry.
Because contrary to popular belief,
just because it's fiber cement board, it's still fibrous.
It can absorb water that will reduce the life of it.
So you don't wanna keep it
in just an absolute damp situation,
but to make sure you have good drainage
into where it can breathe.
And it's critical the backside of that piece
that you see down there, I also primed it.
You can see it comes from the factory
with the front side primed, but the backside is not.
So the piece is gonna be close to the ground
and potentially absorb some moisture.
Go ahead and get that primed and sealed.
One thing that James Hardy says is everywhere
you make a cut, it either needs to be caulked
or sealed in some way, shape, fashion,
paint, primer, whatever that is.
So you don't want any exposed edges out to the elements.
Now, as far as budding two pieces together,
I'm gonna show you today.
I've got to use flashing cards.
You no longer caulk joints
like a lot of people are led to believe.
James Hardy puts that information out everywhere.
So you're gonna see when I butt joints together today,
we'll talk about that.
Also something else that I'm noticing that's critical
that we knocked out in the last episode,
I had to go through and mark every single stud
behind the wall because one thing that is critical
about this stuff is you don't want it nailed
just in your half inch siding
or whatever thickness siding that you use.
They recommend that 66% or 2 3rds of all the nails
that you pop into this stuff has to hit a stud,
but they do give you a freedom for 1 3rd of the nails
to go into your sheeting.
So that does give you some leeway there
because you are gonna miss studs.
That's just gonna happen.
And they also recommend that every butt joint
where two pieces meet together should meet on a stud.
So you will have to do some minor trimming
to make sure you hit that.
Now, the good news is if your studs are 16 inch on center,
12, 24, whatever that is,
once you make your first cut and stop one on there,
start another run on,
because these are 12 foot length boards,
it should stop on another stud.
So you're not making as many cuts as it sounds like.
All right, that's some of the basics right there.
We'll go over a little more as I get started.
Let's get set up, get all my tools out,
and I'll show you a special set of gauges
that helps put this stuff up
that makes it possible for a one man job.
So now that I have my first run done, nice and level,
I see where my first joint is.
So you want to do what's called staggering seams.
You don't wanna just keep laying boards on the same stud
with the same seam and same butt joints
going all the way up to the roof.
It just does not look good.
It's not structurally sound.
And again, it's not pleasing to the eye.
So I like to go back every couple of studs.
I like to stagger a minimum of three runs.
So I'll go back two studs, put a seam here,
go back two more studs for the next run up,
stagger a seam there, and then repeat the process.
So you'll wind up making the same three cuts
to start every time,
assuming everything is nice, level,
and plumb like it should be.
Now, when working by yourself,
I highly recommend you get one of these.
This is a Bosch laser tape measure, basically.
As you can see, it's got a laser that comes out right here.
So for example, I know I've got this stud marked right here
by a line that y'all probably can't see,
and I'm running all the way down
to the trim at the end of the building.
So I'll shoot this down there,
get my measurement, nine feet, one inches.
Now, here's the thing that James Hardy recommends.
Anytime you meet a solid transition, like a piece of trim,
you actually, that's a joint that you want to caulk.
Now, you don't have a solid push together joint,
or otherwise you can't force caulk in there.
They recommend around an eighth of an inch gap
that you'll leave.
So I'll take this measurement, minus one eighth of an inch.
I won't butt all the way to the trim down there right now.
I'll leave that eighth inch gap
that I can come back later and caulk.
We're good to go.
Now, as far as the two pieces that we're gonna butt together
and once we continue to run down the house,
you do not leave a gap in those.
You can, and I do have some minor gaps,
but they recommend you go ahead and butt two pieces together
and flash it with metal flashing.
I'll show y'all that as we get started right there.
But they claim this stuff does not expand and contract.
There's no point in having two butt joints together
with caulk forced in there
because as the temperature changes out here,
the caulk will eventually shrink, expand, it'll crack,
and you'll have water penetration through there.
That's why that flashing is so critical.
All right, so this says nine feet, one,
and one eighth of an inch.
So we'll just make this cut nine feet, one inches
so we can take that eighth off
for that caulk gap that we need.
As far as cutting this stuff goes,
there's a couple different options out there.
I happen to use the circular saw method here
and there is a specific blade that's designed
just for fiber cement siding.
Lots of different companies make them.
I strongly suggest you get one.
If you cut this with a regular wood cutting blade,
it'll dull up quickly.
Now this particular blade, I've had for probably 12 years
and I have done thousands of square feet
of hardy siding with it.
What I wish I had bought,
but I didn't really remember seeing back in the day,
was what they call shears.
So it almost looks like a drill with scissors on the end.
It's metal shears just for cutting this stuff.
The reason I recommend that is there's no dust, no mess.
It's relatively quiet and it's just safer overall.
It's hard for me to justify buying a set of shears,
being that this may be one of the last
hardy board products that I do.
This is our forever home, we certainly hope.
But I won't say that a set of shears is not in my future.
So in the meantime, I'll just cut it with a circular saw.
You can even use a side grinder with a diamond cutoff disc,
although that probably won't get you
very clean straight cuts.
That'd be good for odd situations.
Now the dust that this creates is not good to breathe,
so I do recommend that you use glasses
and a respirator for cutting this stuff.
And it's a beautiful thing about the shears,
no dust, no mess.
Now the other thing I recommend
is you always support this stuff.
While it's supposed to be an amazing product,
and it is, it's quite brittle.
So if you try to go picking up a piece
or support it across saw horses or tractor forts like this,
without a board backer,
this stuff will actually crack and break on you.
You don't wanna do that.
You always wanna support it as wide as you can reach
to carry it over.
Now another good point,
since I just made a cut right here,
so I have an unprimed factory edge.
This is the side that I want to put where the trim is,
since I'm going to force caulk in here.
Because again, any uncut edges
are supposed to be painted, primed,
or have caulk covering the ends.
You wanna seal it in some way, shape or fashion.
Now the other end still has a primed factory edge
that looks like that, minus all the dirt.
That'll be a good edge to butt out here in the field
to another one, since that will remain sealed
and I'm technically not caulking my joints.
Although I probably will, even though it's not required.
Now this is the biggest tip that I can give you
when working by yourself.
This is what makes everything possible.
So this is called a set of siding gauges,
fiber cement siding gauges right here.
There's all different kinds out there.
And most people you're gonna see recommend the Gecko gauges.
They're a slide up, under, and clamp on type of gauge.
Highly rated, excellent reviews online.
I recommend them.
The thing of it is, I bought these probably 12 years ago.
And the old saying says, if it ain't broke, don't fix it.
These work so well, they're about half the price
and they're still holding up great.
They're so simplistic.
It's just been hard for me to justify
buying another set of gauges.
But these are made by Malco.
I'll put the link down in the description.
They still make them, even though I've had mine forever.
Get them off Amazon for 20 something, 30 bucks.
They work awesome.
So once you get that first run of siding set up down there,
you go and slide this right over top of the siding.
You put your new piece in right here
and it catches on this.
That sets your inch and a quarter overlap.
So you gotta understand, anytime you have this siding,
you buy it in different sizes.
Six, seven and a half inches, eight and a half.
For example, or excuse me,
six, seven and a quarter, eight and a quarter.
For example, I bought the seven and a quarter inch stuff.
So once it overlaps an inch and a quarter,
which this presets automatically for you,
you get a six inch reveal.
That's what's exposed and open
before you hit your next piece of lap siding and goes up.
So this hangs on your first board, these two.
You drop your second piece in, you pop a few nails in,
you push this down, the board drops in.
Now you can see you got a dip here.
So you literally lift this up, pull it out.
These are nice, lightweight.
They go in a pocket tool belt.
That's something that Gecko doesn't offer.
They're a little bit bigger and bulkier.
I do like the size of these right here.
All right, so all you do is pop this couple of nails in
to keep everything nice and level.
Push down and you can release this right out.
Let me show you on this one right here.
So I've got me a nail popped in just about flush.
So you just press this spring loaded piece down.
Your board drops back against the house.
Now you can lift up, pull this out.
So the reason you only pop a couple of nails in
is so you can get this piece back out.
You can see we're still loose.
So now we'll go along popping in every single stud
that I have marked, and that'll tighten this right up.
You can also take a hammer and pop the two nails in
that you already put,
and that'll really help cinch this tight.
And as you can see,
I have left me about an eighth of an inch gap over here
to fill with caulk anytime you meet trim.
All right, so now anywhere there's a butt joint,
I always stop and do not nail this last piece in
because you have to use what's called a flashing card.
My inspector actually requires this and looks for it.
So if you put this card in behind this piece,
you can see it now carries down over the next piece.
So since we are not caulking these butt joints,
we're just putting them together.
If water drives in here, which it will,
it hits the metal flashing card,
gets forced down to where the next piece of lap siding is,
and you never have water
that gets back here behind the seams.
Now you want to make sure the card stays just up
so you don't actually see it outside,
and go ahead and pop your nail in.
Now that card will not go anywhere,
and I can put my next piece on,
and it's metal flashed on the backside.
I also forgot to mention that I'm running a Cole nailer
with galvanized ring shank nails.
It's critical that you use galvanized on this stuff
because it is corrosive to a nail.
Plus, you should be using galvanized on anything exterior,
and the ring shank really bites into the wood good,
holds this stuff tight so it never backs out.
All right, so now I'm reaching a point
where I have things like this.
So you've got two options.
You can either notch the board out and slide it up,
which is what I'm gonna do, put a filler piece in,
or you can get like a boring,
diamond-coated boring set of bits
to cut out for pipes and things like that.
Now the problem is we are right in the middle
of pressure testing this gas line,
and this is gonna have to go on for a couple days
till I get the inspector out.
So I can't unscrew all this, make a nice hole,
and I don't have the diamond boring bits.
I've always done it with a jigsaw.
So let me show you how I'm gonna notch,
slide this up and over,
and then we'll caulk the little piece
that goes back in there,
and then we'll stop this piece right here for convenience.
We'll have to do some more notching
around this pipe right here and slide up and over.
It's just kind of the way it's gotta work.
Eventually, we're gonna get up here
to these pipes that are sticking out of the wall
for electrical, we'll have to cut out for those.
And next run, we'll have to actually notch out
around the window.
So a jigsaw is really good for a lot of this stuff.
So I've already drew out where I need to notch out
for that pipe.
Obviously, we might as well round over.
I'll make a little rounded bottom,
less than I have to fill in with caulk later.
This probably isn't the most professional way to do it.
A good set of diamond boring bits
would be perfect for a situation like this,
but I just don't have them.
And these jigsaw blades work pretty well.
So these are carbide-tipped Hitachi jigsaw blades.
I haven't been able to find them.
I've had them for 10 or 12 years,
and they work really well for cutting through this stuff.
You can't hardly dull them,
but they're made just for fiber cement siding.
In a situation like this,
being that I've got to slide up underneath,
I can't really put one of my gauges right there,
so I can put one on the other end.
We'll slide in to fit this up in there.
It actually fits really good.
We're nice and flush up top.
Butt these two pieces together.
I've already got a flashing card back there.
I've already got zip tape flashing around my pipe.
So if the water does drive in, we should be good to go.
All right, so don't forget the next piece.
We'll come down an inch and a quarter.
That will almost close our gap up,
but I would like to cut a piece to fill back in here
so we're not using much caulk at all.
All right, so I'll take this piece that I trimmed out,
stick it in here, and pop it in
with now my very leaky brad nailer.
I don't know what happened.
All right, so that's ready to go.
Like I said, I know there's more professional ways to do it,
but once I lay this next piece down to here,
you won't even see the filler piece that I put in there.
And I may eventually put a cap on the outside of the house,
one of those decorative chrome caps or white caps.
It's made just for a pipe like this
to make it look a little better.
But what I'm most likely gonna do
is when I spray paint the house,
I'm gonna spray paint this pipe.
Everything else, and it'll just blend in with the house.
So now that I'm on my third run,
I know that I am repeating the same cuts.
So you can see the very bottom run
is now I'm gonna mirror it again and do that every third.
So I can see I got a cut down there.
The next cut's all the way down here,
which lines up on a stud.
So I need to get a measurement from here
all the way down to that thin little piece
that's sticking out.
You can't hardly hit that with the laser
and lock it in at the same time.
So I just take one of these old cheap aluminum flashings
that I'm using right here, bend it in half,
and check this out.
So a laser works off of a reflection.
It's gotta send a signal out,
reflect it back to measure the distance.
So if you bend that into as perfect of a 90 as you can get,
it doesn't have to be that precise,
and slide that behind here,
now I have this nice big area to hit
with my laser right there.
So since I'm wanting to repeat this cut right here,
I just line up where my stud is,
where I can clearly see,
hit that piece of reflective material down there,
and I'm locked in.
Now here's the thing,
because all my studs are spaced evenly,
I should be able to use 12 foot pieces no problem,
but some of them have been stub cut for things like this.
So that's a cool little trick
if you're needing to catch a measurement
on something that's hard to hit,
use something reflective like that.
Now once I get out here in the wide open,
I'll set everything up to where
you're only making the first three cuts,
you're running 12 foot stuff,
so I'm making no cuts out here in the middle,
because, well, once you get on out here,
there's nothing in my way.
And then once you get to the very end,
you'll have to do some minor cutting here and there.
But the ultimate goal is no cuts in the middle,
but windows, all kinds of stick outs, things like that,
are gonna require constant cut and constant measuring.
Now where that metal card is also helping me,
now I have to trim out for a window,
so I can just take this real quick,
butt it to the edge of the window,
hit that card, I got my first measurement,
I can come right here to the other edge of my trim,
where I know I need to notch up for the window,
hit that metal card down there.
Now I have both of my measurements to transfer to the board
to trim out for my window.
So here's the other cool thing about these gauges,
and something that you can't do with the Gecko gauges.
So I've just got my measurements
on the outside of the window,
now I need to know exactly how much to take out, right?
So, just put one of these gauges,
you know that right here where this sits
is an inch and a quarter.
So you can actually use that to measure up,
and it looks like about three inches from the bottom.
I need to take that whole section out.
So I've made my two lines right here and here
on the outside of the windows
that I've got off of my laser tape measure,
and I'll make this the bottom,
and I said, from three inches up, we wanna take out.
So if you look right here on your speed square,
there's one, two, three, four, five,
all the way up to 12 inches on this one.
So I'll start my tape measure,
so I'll start my line at the three inch mark,
and there we go.
All right, so let's see how well that worked out.
And keep in mind, when you have a large section
cut out of a piece like this,
you've gotta be careful or it will break on you.
All right, that looks good, looks real good.
All right, well, it is starting to look like something.
And I can tell you what, I am beat, and I'm burnt.
The sun got me today.
So the aggravating part's over.
I was hoping to make more progress than this today,
but I'll tell you what,
you just don't realize the time involved
trimming around little things like that
and all that stuff over there and that.
It just, it takes time to get all that lined up correctly.
So now I'm on the easy stretch with one big problem.
I can't really reach much higher than this.
So while the runs are about to get nice and easy,
now I have to do everything from ladders
and that tractor basket and everything else,
and that's gonna slow it back down.
So I think I'm gonna get out here tomorrow morning
while it's cool, try to get a few more runs up
and get under that overhang in case it rains,
and it's just getting straight on the lap side.
But I did all this because I needed to get past
those two inlets and outlets right there
for the sub panel and meter box.
I am rushing toward a roughing inspection.
I've already scheduled it for the electrical.
I've got to get the meter boxes on out here.
I've got to get ground rods down.
So I had to get the siding on the house
so I can mount those real quick.
So I'm gonna have to dog off the siding
to get back on all this other stuff for inspection
and then turn around and come back to the siding
and ultimately the soffit up there
so we can finish the siding completely out.
It's a juggling act, but I signed up for this.
Thank y'all so much for watching.
Hopefully you enjoyed this.
Hopefully you got some little tips
and pointers from this stuff.
I'm still learning myself a lot from y'all,
a lot from reading, and I'm sure I made some mistakes.
I know y'all will call me out on it.
Don't forget to read the comment section
if you're really wanting to learn about this hardy siding
because I guarantee there's gonna be
some good pointers down there.
Thanks for watching.
