How To Fix AAC Blocks In Building- Practical Video बिल्डिंग में एएसी ब्लॉक्स को कैसे फिक्स करें

Hello Friends Welcome to the Knowledge Hub Channel Let's learn together Today we are going to watch the practical video of Autoclaved Aerated Concrete Blocks AEC Block Fixing We have already created a video about AEC Block Properties and Rail Build Comparison You will find the link to that video in the i button and also in the description You can go there and watch the video So let's start our today's practical This is a renovation project for an old house where we are removing brickwork and doing blockwork First of all it is very important to do the layout of the blockwork So this layout is done according to the drawing It is also very important to check its wall distance and its diagonal The initial layout of the blockwork is called Pehni in the local language Accordingly it measures the entire dimension from both sides of the wall and from the opening side The bottom layer is the starting layer It is very important There was a whole wall on it You have to take a lot of care while doing this Look he is checking the measurement over and over again with this tape Along with that he is also taking measurements from the wall in front to check the cross So that we get that dimension Its bottom layer has a mixture of crushed sand and cement in it And in the front and top they use chemicals for the AEC block There is water in it for the joint They use chemicals While joining this block one more precaution is given Its line should be perfect And its vertical plumb should be straight Accordingly the front wall is also straight The main points are the line level and its plumb This should be perfect And its dimension according to the drawing And this is an AEC block An AEC block is lightweight So it is easy to install And because of its large size compared to brickwork its construction is fast So it is preferred in this case And after installing a full-size AEC block if there is any gap a small piece is cut and inserted there You can see that it is measuring the wall's dimensions This AEC block is 100 mm thick and 150 mm thick In this case a 100 mm thick AEC block is used where there are bathroom walls And a 150 mm thick block is used in the main rooms This is a chemical called DuraBond which is used in the joint In this water is mixed and applied in the vertical and horizontal joints The surface of this slab is a bit uneven There is some concrete here and there So it is removed and cleaned And after wetting it with water the entire mortar is laid on it and the blockwork begins And this layout is so important that once it is complete the responsible architect or engineer checks and approves it And only after it has been approved does the next layer or the next wall construction begin Its line level is the most important thing While checking its level a level pipe or a level tube is used Mortar is laid After laying the mortar these blocks are placed on it While placing them the level line is checked and the plumb is also checked This is the AEC block of the main room 150 mm thick blocks have been used here Clean the slab surface and wet it with water And after that the mortar is applied and the blocks are placed on it This is the main procedure After fixing the main blocks of the entire size the small space is taken according to its dimensions And by cutting it you can see by cutting it with a machine it is placed This is the block that has been cut It is situated in the center Along with this its line and level are also checked and the plumb is also checked A layout has been found here You can see the layout of the floor level After checking it the upper layer is started Now the upper layer has started This is the AEC block of the main room And while placing this block the chemicals are used on it After applying the chemicals they are used on the horizontal and vertical joints And after spreading this wall a binder is placed 1 meter away Binder refers to 100 mm thick concrete That makes the wall very strong And the next layer starts on that binder Here in this video you will see that binder And the next layer starts on the binder And while working on this layer the right distance and the plumb are checked And the chemicals are applied on the horizontal and vertical joints These binders are also known as partial beams Reinforcement steel rod is also placed on it 100 mm of concrete is placed on it The verticality of the wall is checked by the plumb After putting every layer it is checked with a plumb line It is also checked with a line And the distance between columns is also checked by the drawing And its cross check is also checked by the tape from the front wall Here you can see that the plumb is checking the verticality of the wall In this way the wall of the AAC block is completely completed So friends we saw how to fix the AAC block We also saw its practical video Do comment on how you liked today's video If you are watching my channel for the first time then do subscribe And press the bell icon on the side So that you can get notifications for all my upcoming videos Thank you