Creating Jigs for Cutting Common Lengths

DirtFarmerJay
310 followers
3 Video Views·Jul 18, 2013
Dirt Farmer Jay shows you how to create a jig, from spare materials you might have in your shop, to use when you need to cut multiple pieces of wood all the same length. Not only does using a jig save you time, it also greatly increases the accuracy of the cuts - allowing your project to come together with more precision and higher quality.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com with another shop tip.
I'd like to give you a real quick method in which to measure and mark
commonly used lengths that you may have in your shop or projects that you make.
Let's suppose you make outdoor furniture.
In our case, we do a lot of children's furniture, bunk beds.
There might be even in a framing crew some pre-cut blocks that you use.
Now, if you have a sliding miter saw, chop saw, whatever you'd like to call it
that has saw stops on it, you can certainly set them up for repetitive cuts.
However, we have found in our production runs that many times you're cutting 5 of this,
10 of that, 8 of this.
And by having these pre-done measuring sticks,
I don't have to pull out a tape measure every time to mark it.
And it doesn't make a difference who's really marking it and cutting it.
We get predictable results ongoing no matter who the cutter is, so to speak.
So to do this, it's really easy.
The first thing you're going to start with is a nice piece of pine.
This is number 2 pine. It doesn't have to be something fancy.
It's regular 3 1⁄4-inch stock after it's planed.
And I cut it to about 1 1⁄4 to 1 1⁄2 inches long.
This particular piece of wood is 28 1⁄2 inches long.
And let's suppose I had a component that I use ongoing for 28 1⁄2 inches.
The first thing we do is just simply cut this to length
because with the hook that I'm going to put on the end,
you're going to actually use the length you want to make your jig.
The second thing you're going to do is attach a fender washer on the end of it.
As you can see, there's a fender washer right there
that allows you to simply hook over the end of a piece of wood your jig like that.
See?
So by doing that, if this is a longer piece of wood,
I would just simply mark on the end here onto the piece of wood I'm cutting,
and it'd be correct.
So one thing I need to do is put a fender washer with a screw on the end.
I usually use about a number 8 flathead wood screw.
You could use a drywall screw.
I just go ahead and pre-drill the end a little bit here just so it doesn't wander.
So I'm just going to put that in.
Simply insert the screw through the washer.
By doing so, you can see that I have a piece of washer hanging over on both sides.
Now that will catch on a piece of wood that I'm cutting.
So if I go like that, now if I put a mark right here,
it's going to be 28 1⁄2 inches.
I could cut that, but you can see it's a very fast and speedy way
to come up with these measuring sticks.
I go ahead and clearly mark them with a large felt tip,
spray them with a fluorescent paint so it makes it really clear that it's a jig.
I also go ahead and drill a hole in the end to hang it up.
One other thing I just wanted to mention here.
This is a dual-length stick, and if you notice,
there's a notch right here that's marked 26 inches.
So I can either use it over here at 30, hook it on the end over here,
and use it 33 here, or by putting a mark right here, I can get 26.
Both works really quick.
This is a great way to use up some of your scrap
and put predictability and consistency into woodworking cut lengths.
Hope you found the tip helpful.
If you did, like the video, subscribe to our channel, write a comment in.
Until the next time, this is Dirt Farmer Jay from DirtFarmerJay.com.
