The brand new Zhiyun Crane 3S is out and many people are wondering how to mount cinema cameras on the new gimbal. In this Crane 3S tutorial, learn how to mount cinema cameras using the extension arm but be careful when you're doing so!
The Zhiyun Crane 3S is officially announced and I know a lot of you guys are actually super excited
about the new gimbal and in my first looks video I showed you guys that I was able to mount a red
camera on the gimbal and a lot of you guys were asking me on YouTube and on Instagram how I was
able to do it. In that video I briefly touched on the extension arm thingy-ba-bobber but in this
video I wanted to show you guys the two reasons why the Crane 3S is able to mount cinema cameras
after they were able to redesign the entire gimbal. The first reason is that Zhiyun has
tilted the roll arm axis to exactly 55 degrees. Not only does it give you a clear unblocked view
of your LCD screen and your monitor, this also gives you a lot more clearance for your taller
LCD screens or if you have a V-mount battery attached to the back of your cinema camera or
in my case the eyepiece on the C200 and the big A60 batteries. The second reason is because of
this extension arm. So you're able to take apart the roll axis and attach this piece right here in
between so that you're able to accommodate these bigger cinema cameras. Now obviously if you have
a DSLR you don't need to add on this extension module unless you have like a super duper rig
or something like that but in general DSLRs extension arm not really needed cinema cameras
definitely needed. So let's go over how you can attach and detach the extension arm. There are
four tiny hex screws on the roll arm that you have to take out. You want to be super careful not to
just rip apart the arm because underneath it is wiring. You don't want to accidentally break
anything in the wiring because essentially you're breaking your gimbal too so take it slow. Once you
take the axis arm apart you can loosen the extra bit of wiring that they give you to mount the
extension module. On the module take the little foam sticker thingy in the middle take it off
slip it right in between the arm and go ahead and attach the other side of the extension module
using the original hex screws and the extra set they give you. That middle empty section is where
the wiring will go and I recommend that you don't peel off the adhesive on the foam sticker especially
if you're planning on taking the module off and on for whatever reason. It fits perfectly in there
with the wiring underneath it so I wouldn't bother with sticking it on and you're good to go. I do
want to mention that once you attach the extension module on the gimbal it makes the entire footprint
of the gimbal a little bit bigger which might be a challenge if you're traveling around with it so
keep in mind that you might need the extra space to store the 3S. So putting the extension arm on
is relatively easy and simple but taking it off is a little bit more complicated and I wish that
they made it a little bit simpler. So to take the extension arm off start by unscrewing all
eight hex screws peel off the foam sticker and you're able to remove the extension module.
It's pretty impossible to just try and stuff all the wiring back into the little tiny holes
trust me I tried didn't go well. So what you have to do is loosen the tiny plate on the underside
of the roll arm the part that's closer to the tilt arm and then try to carefully put the wiring
inside and then after you've done that close it up again. It's a hassle to do but make sure you go
slow in order to avoid pinching or damaging the wiring at all. I know it sounds simple if I say
it out loud and I kind of you know realize that now but it's actually a little bit more tedious
the whole process of taking the arm off is a little bit more involved than I would have liked.
I wish they had like a simple latch mechanism or like a locking mechanism that's much easier and
simpler than this whole process right here. Obviously this isn't so much of a headache for
those of us who are just only using cinema cameras or just only using DSLR slash mirrorless cameras
either you'll put it on and never take it off or you just never put it on and in my case I'm probably
never going to take it off unless I have to do another video which would suck hopefully I don't
have to do that. Maybe in the future they have a simpler solution for us but for now that's it for
this video I just wanted to give you guys a little bit of insight on how you can mount cinema cameras
on the Zhiyun Crane 3S. If you like this video please hit that like button make sure to subscribe
hit the bell to get notified of every video that I post. I will be making more videos just like this
one about the Crane 3S so make sure you stay up to date on everything. My name is Alex Chung and
I'll see you later. Bye!