Make your own Wire Base for a Beaded Snowflake Ornament

Tech Level
93 followers
15 Video Views·Nov 15, 2022
Make your own Wire Base for a Beaded Snowflake Ornament
I'm going to show you how to make this beautiful beaded snowflake decoration
for the Christmas tree or you can hang it anywhere in your house or in your rear view mirror.
And what you're going to need for that are some pieces of wire. You could use about a 20 gauge
wire. I have three pieces that are four inches long and then you need another piece of wire
that's a little bit longer about six to eight inches and it's a thinner wire because you want
to be able to bend this one much easier. And how you start is you just hold it about an inch
from the end of the skinny wire around the middle of the four inch wire and you're going to do one
complete twist around and do it really firmly like really pull on it so it's nice and snug
and then you're going to get your next piece of wire and just try to center it around like that
and with a bit of an angle there because we're going to have six edges all together so we're
going to twist that one around like that. Now once you've got your two pieces secured like that,
at that point you can cut this little end here because you don't need that little end.
So we'll cut the little piece that was overlapping there. So then you're going to get your third
piece of wire and if these need adjusting to get them more centered now's a good time to do it.
So you're going to get your third piece and then put it here. It's going to start looking a bit
like a spider web and you want to make sure it's also centered. So you're going to do that and now
you're going to bend the skinny piece around that one. Okay and you want to make sure you go around
all of them at least once so they're really secure. So now at this point you can just
rotate around. Make sure you're keeping sort of about an equal angle in between each one.
You can adjust it as you go and you're just going to keep going around.
Make sure you twist it around each wire and again around that one and then at least go back over the
first one once. Okay and you can go around a couple of more times if you want it more fancy
but I prefer to leave more room on the wires for the beads. So at this point if you need to adjust
it a bit you can and you're going to end up with this kind of star shape like that. And then what
you're going to do is start putting on your beads. So I've already kind of pre-determined
my pattern what I want to do and so I'm going to start with one edge at a time because if you do
two sides at the same time you're going to start losing your beads. They're going to start falling
off. So now I'm going to put my pattern of beads on there. So we have I'm doing like a this would
be about a six millimeter bead and then I want a little variety so I'm going to do a little one
next. It's about a four millimeter. We'll do that one next and then this is more of a little flat
bead. It's always interesting to have different shapes and in the middle I'm going to put a bigger
bead sort of for a little more impact. And what I'm doing for this one is I'm alternating with
clear and white beads and even putting a couple of little pearls on there too. And these are
these little three-sided beads are actually called tri-beads so you can use some of those too. They
make it look more snowflakey. So once you've got all your beads that you need like that you have
to bend the end. You're going to do each one as you go so you won't lose your beads. So you're
going to hold it carefully, take your round pliers and carefully twist the end like that.
And you want to be careful not to pull this wire out that way too much otherwise you're not going
to have enough room on that side. So usually what I would do next is I'll do that side next and then
I'm going to do the other sides like that. So I'm just going to finish it off and you might notice
as you're beating around that the last little end is a little shorter just because these beads get
pushed up in the middle. So just make allowance for that when you're choosing your beads that
you have enough room to twist the end. Okay so we're going to twist our last end and there's our
snowflake beautiful decoration and so now you're going to put a ribbon on your snowflake decoration.
So choose one of the ends that is the largest the largest loop that you can put a ribbon through
and you can either put a clear kind of fishing line type cord or you can get a red ribbon for
the Christmas time if you want. So we're going to put the two ends together like that do a loop
around the finger and put the ends through to make a little slip knot. And there you go
your little snowflake decoration for the holidays.
