Motorrefit Saildrivemanschette wechseln und Kielriss

Zulu Sailing
4 followers
Nov 15, 2022
Winter work Schnatzi What have we actually done
What have we done so far We installed the kitchen so we took out the old kitchen unit
There was just a stupid refrigerator in there which was too small too heavy and didn't work either
And wasted space
And were lucky that in the winter we got it from someone who had given up on it
So have we received an awesome compressor cooler as a gift
And around it we built our new kitchen from such thin plywood
With so many cabinets for olive oil for extraction for such fine items and more
My first built-in kitchen in my life
Yes even in the apartments where I lived there was either a real sturdy built-in cabinet in there
Because there was no kitchen in the apartment
And actually we ourselves had one built in
It is also very important that the kitchen is straight
But we had one ladder and then the other
And now the board has become bent and fits perfectly here in this curve
Did the strip do a good job
or didn't it I think the strip did it right
I'm limiting the damage from our kitchen parts here
We had it made so stylish and now since our boat has a lot of white we wanted a bit of wood
Make the edges also look cool white
Then we sealed it with white caulk
And to make this work so cool we taped it here with Frogtape
Then it had completely run under
And Max had luckily noticed it
Then we had already removed the coal dust
with spirit as the resin had not yet set
But here so many edges have formed
And I'll sand it down now and
then we'll use classic white
paint and try to paint it freehand Let's see if it works
We also want to install the kitchen In three weeks it will
start And I would like
to take the kitchen with me
Then we replaced and reconditioned the valves
We had three before that but none of them worked properly
And that's not the point of breathing valves
We replaced the exhaust valve with a new large one made of brass
We also replaced the intake valve
We replaced the one at the Sail Drive
It was one of those annoying original World War Panther plastic parts
It simply broke apart into its individual parts right when I started taking it apart
And it wasn't very trustworthy
And that's why we also installed a regular brass valve there
Then we replaced the Sail Drive seal
Also we completely removed and disassembled the gearbox
And the Sail Drive boot was replaced
The old one didn't look too bad
But better safe
Then we had because we lost coolant from the engine last year
We found out that our environmental pump is leaking from the cooling circuit
And we have removed them and installed a new one
And then decided that since the engine was nothing but a pile of rust
Because we want to drive it for a while longer that we completely strip it and spray it with zinc
primer and paint it completely new
Now it looks almost brand new
And in the process they also replaced all the hoses for diesel and coolant and so on
These were ordinary garden hoses before
The diesel had really released
the plasticizers That didn'
t look good either Then we installed a new water separator
The old drain plug was broken at the bottom
And the drain plug wasn't really available as a separate part
And we really wanted another one like that where you can look through the glass from below
Then when the emulsion separates if there is water in the diesel
Also we should separate the part from the engine that also holds the engine
here because the engine has no support on this side here
And also have the screws already loosen so
that everything is loose here and then support it with wood
I think that's just as uncool as the Selling-Würther-Die-Typ
I would like to support the motor first with wood and then remove the screws
And I don't see any disadvantage in it that's exactly how the Selling-Würther-Die-Typ did it
We can't just pull the Sail Drive out of
the hull like usual because we don't have a rubber lip at the bottom
But our swift flounder is too laminated down there for optimal flow conditions
Therefore the Sail Drive and the gearbox are separated upside down inside the boat
So the gearbox is in and out
We will take this home now and can clean it comfortably at home
And yes it worked much better than expected with the Sail Drive in the laminated hull
I let him in and there's no need to have
such a rubber lip and you don't have to take it out
It works surprisingly well even if you have the same problem
Yes our old Sail Drive coupling
After the expansion we discover a few bubbles that have formed somewhat
But there are also a few stone chip impacts visible on the back
But even when we lift them and shape them back and forth
She doesn't look that bad considering she's from 1994
Also this is now the black one is just corrosion protection
Yes this is basically the same sealant we will need later
But I just do it here for corrosion protection
And leave it free where the O-ring and the rubber seal go
Because the manual says it's a dry seal
She does her job so to speak without this stuff here and probably even better without
Then we put on the cuff
Here is the front and there is the valve
Also we make sure that the date comes to the point where we can read it later
My Sail Drive needs to be adjusted to the Sail Drive extension
I somehow still find it a bit pointless that in areas like this
Because here comes the Sail Drive with its holes I know
those too but still water ends up in the entire ring
Then the paper gasket gets water all the time
Yes but only in one place where she should not be writing
I think as I said that they absorb this stuff in other
areas and then become sort of solid you know like I mean
Do you mean that also protects the paper from moisture getting everywhere
Yes I think it's kind of a resin if you will that seeps into the paper you know
Weil das was wir da rausgeholt haben gar nichts mit Papier
zu tun hatte das war einfach nur ein vollständiger Festkörper
And I think this stuff here helps the paper to perfectly conform to the shape
To the small grooves and so on that were still in the aluminum here before sealing
This is all super smooth but also still as smooth as possible
When the rope has come out it will also go back in
The rope seal is sealed then the paper gasket and then the already prepared gear unit
Adjust the cuff reassemble the extension structure and tighten everything upside down
To rule out the overheating issue we wanted to take a look at our heat exchanger
However we could not simply pull it out
Why we have not exactly known until today
We pulled him as far out as we could and
decided that he actually looks pretty okay
We could of course not detect microfractures
Actually we wanted to perform an air pressure test underwater to see if there was any leakage
But the option was out anyway
Yes I'm just in the process of rust removing the engine
It's not nearly as much fun as I had hoped
because even our cool little device here the Proxxon
Here in so many grooves where it somehow doesn't fit and then remains as handwork
But we still want to keep our
engine and make it work so it has to be done
I'm doing this here with the Proxxon Max is doing it with the Flex the large areas here
A few too many sparks are flying
Max is currently below deck painting our neon anti-fouling
Now the sun has come out a bit
We are taking advantage of the good weather And I think there will still
be a lot of manual work left Let's see how
many hours we'll have to spend on it
It just isn't moving forward I mean
you know if you open up a hood today
Then everything is square and covered with plastic
Of course there are probably also corners
But if I were to design a sustainable motor that I
could maintain then I would put such stupid corners in
I mean how would you even get rust in the first
place Why does that corner even have to exist
Why can't it just go down and be smooth I think I
would call an engine a box
So square and practical
This is really
Otherwise I am usually patient and enjoy fiddling around
But no this is really annoying
A monster A real monster
And I hope it's worth it and that he doesn't complain anymore this summer
at the radiator no longer throws a heat alarm that it doesn 't
constantly mess up our freshly painted engine compartme
and that we have a few more PS
That is indeed our goal
Timi would say that he's been assigned to clean the machine
We have decided that we won't remove the entire color from the engine
but only worry about the rusted spots
Because taking the entire color off would have really taken some time and some nerves
Do you feel like explaining why we're doing all this work with the engine right now
Cooling system blah
Or later
Well get the cooling system sealed
Oh right because that's the only rusted part here
We have already replaced and sealed the water pump and are
now putting new caps on the radiator to make sure it is sealed
Because the entire water here has naturally produced a lot of rust
We will paint it again so it looks nice and is protected and doesn't rust anymore
Also we will then also find it faster if something is wrong
somewhere or so you can see more quickly where it comes from
And we hope for better performance
That through the radiator not by painting
Really You think he looks burned out
I think he looks like a soldier now
All with zinc primer and rust conversion
And tomorrow it will
be green After a thorough spirit cleaning the
engine gets two layers of zinc primer and then two layers of paint
Now he shines again almost like new
One can still see his age a little
It's time we want to start the engine
We think we have all the parts back
Cross your fingers and one two three
Yes it's running
He jumped on the first time
We certainly did not expect that
We had prepared for Jokulei and had to ventilate
We are overjoyed and hope that he will continue to perform so well throughout the season
Yes what else did we do
Oh we've installed a heater It gets the coolant
from the engine and has a kind of heat exchanger
Then nice warm air flows
into the ship Of course only when the engine is running
The packages that are delivered to us are getting bigger and bigger
The one from the heating is definitely the biggest
Installing the heating was also not exactly easy
As often in the boat work was done on top of the head and in a small corner
It was also quite clever that we had already sealed the sink above
Instead we would naturally install the heating first and then seal the sink
But we only decided to have the heater installed
there when the sink was already in place
We thought the heating would come from a completely different place
But that turned out not to be really feasible or good in practice
And you've forgotten something big Strom
Ah right power
That was also there
Previously I'll say we had two extremely old starter batteries
e ones that could be turned on and off and were responsible for starting and consuming
But in each only about 40 ampere-hours went in
And since we wanted to keep the battery well charged so we could
start the engine we only had 40 ampere-hours of power available
And now we've split it into a starter and a large consumer battery
They had it moved from under the kitchen to the engine compartment
and have also installed new chargers new switches and reasonable fuses
And you had actually pulled almost all the cables at some point and reinstalled them
Exactly and we also pulled almost all the cables again that we hadn't pulled last year
Now only Instruments is open
Exactly the instrument wiring is still a bit open with this strange
old NEMA bus I need to take a look at it again
13.3 volts
Good Plus is being activated but the instruments will be controlled via the autopilot
That means as long as the autopilot is not connected to the panel the instruments cannot function
How did you find that out now From my instrument end
where 30.3 volts are present which is by the way extremely powerful
Only a positive cable goes to the instruments here
The instruments take over via this powerful fan clamp from the autopilot
And I didn't connect the autopilot either
Then we bought an autopilot that works on its own
This is a PIN-Pilot that only needs power to function initially
and can also be integrated later into our control
panel for the autopilot our Flotter and our wind vane
Yes and then we also did some small things
Front the annoying fan connectors at the mast base against proper plugs replaced
Solder one more
The components have lost fluid because the membrane is damaged And the membrane is
no longer available as a spare part
And the companions are no longer new either So we bought and installed other companions We still need
to install one more we have already installed one
Then we sometimes let some things fall off
behind Wardrobes
We made wardrobes
Yes we have made wardrobes out of the water tanks
Also we used to have water ballast tanks
But they were already deactivated when we bought the ship
Then there are of course new
cushions and new backrests and so on That
was also cool Reupholstered cushions
So I will install the wardrobes here Or first
our wardrobe doors which I made in the winter
It should look something like this in the end
So that it doesn't mess everything up when tilted here
The system works roughly like this
Also here you can see this part is already fixed
I have sewn some tabs here at the ends
And into these they fit some plastic profiles
It costs 1.50 euros per meter
at the hardware store And
they then come in here They work as a holding function
That the material does not shift individually
Then I apply super glue to the drill holes
Hole through screw through
Then it comes from the inside and reaches here
Then it holds it roughly
A wardrobe on our boat
Is that cool
or what You can do a lot then
I'll admit the backrest is still missing
But we now have wardrobes
And with wardrobes we are a real sailboat
A real cruising boat
We postponed the dog test then
With the crack detection device
We wanted to check if our pressure vessels have any microcracks somewhere
And there is actually a testing method from the welding industry
To check the welds
And the mast was on the ship
And then I did it the same way as in the instructions
But this pink developer stuff it sprays so finely
It's finer than any lactose
And it was already relatively still
And it's simply everywhere
It even crawled into the cabin
And that's why we
said let's not do this anymore on the ship
We'll have a pink ship as our last option
And that's what we ended up doing
We might do it again next winter or something
The mast has also remained in place
He is still standing
We have revised our proposal
Yes exactly There will definitely be an extra video for this
To our new proposal
For we have chosen something unconventional Yes we do that
in an extra video Do we want
to reveal the material already
Yes we have decided on a Dyneema
But for that we can look into reasons and prices
and how and what and where
Let's make an extra video
Because it's not that simple
But we are definitely convinced of that
Yes
No Told all
in 10 minutes and
worked on
all winter Cleaned
organized Sealed off
Cheaply painted
Just some small stuff
Yes yes A few little things
We also now have a sink on board
Previously the only drain
inside the boat was our toilet
But draining noodles into the toilet is not so
cool Or also brushing your
teeth when it's raining
We used to have to go out on deck for that
No matter the weather or sea conditions I'm
really looking forward to my sink
And that's why I get involved myself
The goal is to align our sink
now So that when the water
is in it it doesn't stand on the other side of the drain
And on land we couldn't do
that because were standing
on land and they couldn't swim and couldn't balance
Now we are swimming and can compensate for it
We forgot the keel line
We had a crack at the keel in the paint
It was so rusty because you can see it so nicely in our yellow color
That was a bit uncomfortable for us We
really wanted to take a look
Then we stripped it down and found out
That it is really only in the color and that it
almost ends with the GFK of the ship and
transitions into the metal keel
The color was torn at that spot and had developed a slight
rust We polished it off
and had it properly laminated with matting over it
and then burnished again and painted over with color
It's nothing too exciting but better to take a look at it
Copyright WDR 2021
