Easy Stained Glass Cabinet Door

ARTyRV GLASS STUDIO
91 followers
5 Video Views·Nov 9, 2022
Hi everybody, Ed here and it's a beautiful day outside and we're in the glass studio
working on one of 10 of these cabinet doors. So we wanted to film the first one just to show you
how it goes together and let you see what the back of the cabinet door looks like. You can see
that it is rabbeted out and I think I got that in the frame. You can see that it's rabbeted out
so that it will hold our lead just like that. So we're using a 3 8 flat h lead around the outside
of this window. It's very simple and we're going to show you now how it goes together.
So like I showed you before, it's just a simple cabinet door. Very simple cabinet door.
And we're making sure that all of our lead joints, just like they should be at any time,
are just right on the money. Just right on the money. Now remember when we start to go up the
side here, we're using 3 8 flat h lead on our project. So when we cut our 3 8 lead like that
on the side, now we want to come back and we just kind of tilt our pliers sideways,
cut that off, and then lay them down perfectly square and cut that angle and make it look
really, really nice y'all. That's what we want to do.
So now we're on the outside of our window here, just like this. Our lead is exactly where we need
it. You know, if all windows were this simple, I could stay caught up. But of course, I want you,
also want you to think about it, that we have, we have 10 of these to build. So it's really not
that simple. This one, however, the customer's picking up later on in the week and they're
going to be checking them out and making sure that they look exactly the way they want them.
So remember, lay your lead in there, mark it, make sure when you cut it that it's square.
Because you usually, you know, if you cut your lead right, you usually don't have any room to
fudge around and goof off. So now we're on number four, which is this long piece going up the side.
That's that. Again, square your lead up, bring it over here, making sure that every
piece of lead is exactly where it's supposed to be before you add another piece of lead.
Just like that. Oh, so pretty. Very simple window y'all, but so elegant. And by the time we put 10
of these around the top of the kitchen, and then there's two more that are going right beside the
stove, it's really going to look nice. So hey, we're going to finish off this top piece of lead
here. And as you can see, that's a goofy cut on that end. And we, but we, we don't have enough
to do that. So I'm going to use this piece of lead right here. And we have perfect amount,
but that ends still just like the other one. So we're going to lean our pliers back at an angle.
Okay. Just like that. And we're going to take that off. There it is. And then we're going to
go straight down. And now, cause if we cut our lead, you know, where the top is longer than
the bottom or the bottom's longer than the top, one's going to touch the lead before the other.
And on the other side, you're going to have a really bad gap and nobody wants that. So we want
to make sure that we get this lead marked exactly right. Cause we're getting ready to get out the
solder and iron, and we're going to finish this bad boy up. A simple cabinet door, nine pieces
of glass, have some fun with it. This is just a two inch border. The center works itself out
and it works itself out on all 10 of the cabinet doors, depending on their size,
because some of them, I think, I think there's two more that are a little bit bigger, but anyway,
we've got it. You see this all together. We're just going to put a couple of little nails in
it to hold everything in place. We're going to get the solder and iron set up along with our
wattage or temperature control, get that ready. And we're going to solder this bad boy up.
Hi everybody. It's Ed here. And we're in the stained glass studio working on this cabinet
door glass today, just kind of showing you how to do it. We're going to take you through the
process. While we're waiting on our iron to heat up, I just want you to know we used a three
eighths flat H lead on the outside, which is perfect for our cabinet door, for the back of
our cabinet door. That way it's going to allow us to push point it and put some push points inside
the cabinet door so that we can keep it in there. Remember, we don't want to really, we don't want
to caulk the face of the stained glass to the wood because you'll never get it out if you have
a problem. However, we are probably, we are definitely using push points on this. And I
haven't decided yet if we're going to use a little small bead of white silicone around and make like
a pocket because we do have enough room. So we're going to decide that when we get to that point
right now, our soldering iron is heating up. We're going to check it and just make sure
that it's hot enough. I have my watt, there it is. I have my wattage controller.
My wattage controller is set right now on 80, eight zero. So we're not going to waste any time.
I've got my Ruby Flux inside my trusty putty container, and we're going to start out right
here on this corner. We're going to come over and we're going to do our touch and go. Remember guys,
touch and go, it works great. And it gives you a nice smooth joint. Now there aren't many joints
on this window. Okay. And when there aren't a whole lot of solder joints,
none of them can be bad because they're all going to show up. If you've got a window with four or
500 solder joints in it, you know, that's one thing they all should look good. But if you can't,
nobody's really going to notice. So remember now that we have a, we have a crossroads right here.
Okay. We have a crossroads. First, we're going to do our T, touch and go, T, touch and go,
T. Now we're going to come down. We're going to do another T on the side, T,
touch and go, one, two, three, a T. Now let's do an X. Now, or a cross. Now, if you notice,
I've got my solder and iron turned sideways. That's because I want an X just like that. Okay.
Touch and go. See that? Those solder joints, because there's only 12 of them,
all 12 of them better look good because you're going to see every one of them. Again, if you've
got four or 500 solder joints and you mess up on one, you know who's going to notice? Nobody.
If you've got 12 solder joints and you mess up on one, you know who's going to notice? Everybody.
Especially the ladies, friends that come in and say,
oh, you see that solder joint on that cabinet door of yours? Oh my gosh.
And I'm going to say, oh, well, it wasn't mine. So here we go. So keep in mind as you're using
your solder and iron, it's cooling off. So you can take like a few second break in between,
you know, in between your solder joints. And remember one, two, three, straight up.
Okay. Here we go. Ready? Three, straight up. Just like that. Here we go. We're doing an X and we're,
our soldering iron is on the diagonal. And here we go. One, two, three, straight up.
Just like that. Can you, I hope you got a good shot of that because everybody's been
wanting us to give them closeups and I'm, we're trying to get as close as we can.
So remember, you see this, that's a crossroads for your lead. And we, we can't, we don't want
to hold our solder and iron straight. We want to hold our solder and iron at an angle to cover as
much of those four pieces as we can. Okay. Here we go. One, two, three. And guess what? There's our
X. X marks the spot, everybody. We're going to pull our nails out. We're going to move this and
we're going to cut this down and we're going to flip it over and do the other side. I sure hope
this is helping everybody. I sure hope it's helping everybody because you know, everybody's doing the
same thing. It's just that everybody else, everybody does it differently. Okay. So technically
when you think about it, everyone, it's not the same thing. And you know what? Even if 12
solder joints, I forgot one. So I'm not sure if we're still taping or not, but if we are,
I forgot a solder joint and that's why you always, you always look at them. Okay. Look at that. See
there y'all. And yes, you know what the next question coming from you is? And you know what
the answer is? Yes. You have to putty it. Yes. Let's solder this other side and I'm going to
show you a way to putty it. We're not going to putty it traditionally. We're going to use our
thumb, but we're going to use the traditional putty because there's no reason for us to get
putty all over everything. We want to, we want to stop the glass from sounding like popcorn in a pan.
Here we go. So we flipped the window over and, um, you know, it was funny because there's,
there's only 12 or 16 solder joints on this window. And you know, I, I still forgot one
before I flipped it over. So anyway, I just, we're going to do this again. This is, it's, hey,
it's good therapy for you. It's good therapy for me. Ready? Now, remember our soldering iron has
been sitting for a few seconds, so we just want to go one, two, three, just like that. Boom. One.
This is a T two, three, straight up. This is a T one, two, three, straight up. Here's another one.
All right. So here we go again. Now we have these, what our crossroads here, everybody,
these are our crossroads. So we're going to take our crossroads and we're going to hold
our soldering iron at an angle, 45 degrees to the window. One, two, three, and there's our cross.
You know, I just, I enjoy doing this so much. And, and, and, and this is true time on this window,
putting it together. We just wanted to show you this start to start the finish
because it's important. So I'm going to show you that one more time. That right there is too much
flux, everybody. Okay. It's too much flux and your iron is too cool. And that's exactly what it looks
like when that happens. So we're going to come over here and our iron is heated back up. Just
like that. Perfect. So sometimes when you have many, many, many, many, many solder joints,
you can work almost too fast and your iron will get very cold. So if you're going to work fast,
which myself, I prefer to do, turn your iron up a little bit hotter,
and then you'll be able to work a little bit faster
as your iron is going to stay hotter longer for you. And that little bit of flux isn't going to
affect you. Okay. This is what we, this is what we got going on. We're going to take just a short,
we're going to do a cut. Ed's going to get the putty and we're going to thumb putty this. So
we're taking some soft putty. We're not going to do the whole window. We're going to do,
well, we are going to do the whole window, but we're not like going to smear it on everywhere.
We're just going to, we're going to pack this in with our fingers here, just like that.
You know, the whole idea, especially in a cabinet door like this is to keep the glass
from rattling. You don't want your customers opening and closing their cabinet doors
and then a whole bunch of rattling going on. So you can see how the putty,
because with the lacquer thinner in it, you can see how the putty starts to dry.
And as it's drying, I said, I'm just scraping a little bit right off the side of the bucket here.
And I'm just using the side of my thumb. Now, when I first started doing stained glass, we didn't,
we didn't break our putty down so that it was soft. We used it kind of like I'm using it now.
And we, and we puttied even big church windows by hand. So you can see this is drying out and
it's really looking good. This putty is going to keep the glass from rattling,
but it's also going to help us. It's also going to help us polish the lid up a little bit.
All right. So you see that side, I just puttied this side and polished it. Look at the difference.
So I'm going to get this back on the, get it back down on the table and we're going to get it puttied.
Okay. So we've, we've soldered it. Now we've hand puttied this one, this other side here,
and now we're going to polish it. So I found over the years, the best way to polish these windows
or to at least polish the lid and make it look like just a nice, dark, pretty pewter is to use
what's called an acid brush. Buy them in the, in the, in your convenience store, you know, in your
little hard, local hardware store. And this one, as you can see, I've had for quite a long time,
but it does such a wonderful job. Okay. So once you get that side done, I'm going to flip this up,
flip it over and we're going to do this side. We're going to make sure that the lid is cut
from the edges and it's perfectly, nothing oozing out. And then once we do this part of the process,
we're going to allow it to sit and firm up and we're going to polish it one more time.
And then we'll install it in our customer's cabinet door. So this is it. Along with Barb,
please, you know, if you haven't subscribed yet, go ahead and subscribe. If this helped you out,
hopefully you learned a little something. Give us a thumbs up. We appreciate all of your input and
don't forget Monday nights at 7 PM live Q and A with Barb and Ed on the RDRV glass channel.
So we finished the window and we've got it cleaned up and now we're going to install it
into our cabinet door. Now the customer already has little holes drilled and I'm guessing that
that's for clips, but they're going to want to pick this up. So we're going to install some
push points in very specific areas so that, you know, they're very unobtrusive. So on this
horizontal that you see right here, this is where we're going to put it. We're going to put a push
point here and we're going to put a push point here. And these are just glazing points. They're
manufactured. Oh, excuse me. They're manufactured by Fletcher. You can pick them up at your hardware
store, but they're very simple little piece. Everybody knows what a glazing point is.
You know, back in the day, they used to take, they would take a upholstery tack and actually
drive that nail right into the wood on top of the lid and hold it in like that. And if you've ever
restored some windows, you probably know exactly what I'm talking about. So I've got a flat putty
knife or what's called a five in one. I'm just going to set my push point right here and I'm
going to push it in like that right there, just like that. Now I'm going to do the same right here
on this other joint. So now again, strategically placing our push point. So if you've ever glazed
a window in an old house or something, you know, that wood is much softer than these wooden cabinet
doors. So we're going to turn that around one more, a half a turn, and we're going to come in
right here. You can see my glazing point. You can see my putty knife. So you just watched us put the
push points in this beautiful little simple, simple cabinet door. And you know, I suggest maybe if
you're, if you're just now starting out with lead, try and lead a small window like this together.
It'll give you the benefit of knowing how things go together without starting out with a very
intricate pattern and not really knowing where to go. So now that we've got this installed in the
cabinet door, we're going to clean it up, get the glass all nice and shiny. And now that I'm smiling,
you can see my happiness that this project is finished. Thanks for tuning in today. This is Ed
along with Barb in the stained glass studio for the RDRV channel. Thanks again for tuning in.
