How to Replace S-Trap with a P-Trap How Drain Plumbing Traps Work Air Actuated Valve Install

Builders and Beyond
48 followers
11 Video Views·Nov 3, 2022
How to Replace S-Trap with a P-Trap How Drain Plumbing Traps Work Air Actuated Valve Install
Well, it's plumbing day here at Brantley Built.
What I'm working on today is replacing an S-trap with a P-trap.
As you can see from the shape of the trap here, these pipes,
this makes an S-shape. This one here makes a P-shape.
And what a trap is,
is a portion of pipe that holds water so sewer gases can't come up and come
into your house.
So to illustrate how traps work and how the water works in your home,
I'm sure you've seen these little vents that pop up out of your roof and then
you'll have a pipe coming down and then there'll be pipes that come into it and
then the water,
the waste water will leave to either your septic system or the city sewer.
When you flush the toilet,
water goes down into the pipe or when you run the sink,
the water goes into the pipe and what allows that water to freely flow down to
the sewer to the septic system is this open pipe.
So think about if you have a straw and you put your,
you put your thumb over the straw and it won't allow the water to flow down the
end of the straw. That's the same principle here.
This is why you have these roof vents.
So you'll see them they're either black or they're white sticking out of roofs
and you have these vents open in the atmosphere so it doesn't.
So it allows the water to freely flow through these pipes because if you don't,
it's the straw principle to where if you didn't have this pipe here,
you try to push water down the pipe and there would be a section that would be
created here and the water wouldn't flow through and you flush the toilet.
The water is going to take off down the pipe and simultaneously air is going to
come into the pipe and it's going to work the same way with the sink.
Obviously the reason I illustrate this principle is it's going to be important
later on because of the type of event that I'm going to be using. Okay,
so why traps are important and why they're necessary is as you flush the water
down the pipe, keep in mind that you're flushing wastewater.
Well there are sewer gases,
specifically ammonia and methane that will drift back up the pipe.
And so how these traps work is they will fill full of water at this level and
they will stay full all the time.
So anytime you wash water down the sink or anytime you flush a toilet or
anything,
it'll keep water in this little area here and not allow these gases to come back
up into your home. And if you wonder why that's important,
if you've ever seen the movie Christmas Vacation,
where, um, I can't remember what the guy's name is.
I should have probably looked it up before I did the video where he blows
everybody up in the front yard. This is the same thing.
These gases are dangerous and of course it isn't going to be on that scale,
you know, of an explosion, but these gases will seep back into your home.
So this is a nest trap and I'm certainly not teaching you how to install a nest
trap because these are actually illegal in the United States in most places now.
And the reason is is as the water rushes down the drain pipe and it comes around
the trap and it, and it comes down into the sewer system,
it'll actually create a vacuum and pull some of this water out with it.
And so instead of your trap being full and not allowing the gases to come
through,
what'll happen is it'll pull enough water to where you might only be this full
where your trap is that high and you'll have sewer gases that will make their
way past this little area here and back into your home.
So what I'm replacing the S trap with is a P trap.
See the P shape, like I said before.
So you're going to wash water down the drain and it's going to come out and
it's going to fall at a 90 degree angle and go out to the sewer system.
And this vent, the reason I mentioned the vent,
the vent is very important as you have air rushing in with the water and make
sure that there's no vacuum to pull this water here in the trap and it'll make
sure the trap stays full of water.
So instead of the vacuum being on the part with the sink,
it's actually on the atmosphere.
Then once again, as the sewer gases try to come up,
the sewer gases can vent to the atmosphere,
but there's no way for them to make it back past this water and into your home.
What I'm installing in this plumbing system is an air actuated valve.
And the reason you use these is they will provide air to the drain system,
but you don't have to try to go through the roof or you don't have to try to
tie into some other vent system in the wall or anything.
So that's what I'm going to be installing here. Same principle.
The water is just going to come down the pipe and go to the sewer system.
The air is going to come through this air actuated valve and allow air to go down
with the water to allow everything to drain properly and then it'll close.
Once there's no more downward pressure of water,
it'll close. So then the gases, once again, can't, it's like a check valve.
It'll allow something, you know, the air to come in,
but then it'll close and make sure that there's no gases going out.
So these are really good if you have a situation like this to where you don't
want to go try to find a vent in the wall.
One thing that I do want to mention when you're doing plumbing,
just like I mentioned with the electrical system,
there's different materials that you can use for the same system.
So I'm using the black ABS pipe, but they all,
but you can also use the white PVC.
So whenever I make these videos, don't look at everything literally and just be
like, Oh, I need to do that. So I need to go find the black ABS pipe.
Just know that this can also be done with a white PVC.
These are pretty much standard. These drain pipes,
usually just get them in packages at Lowe's or Home Depot or wherever.
And so these are pretty standard. You won't find these in different colors.
These are what they are. So like I said, this is going to connect to the sink.
We're going to come down to the trap and the water is going to come around,
drain down and the air is going to come through this air actuated valve.
These air actuated valves,
they do need to be installed at least four inches above this T here.
And obviously whenever you're doing plumbing work,
make sure that these T's go in the same direction as the flow of water.
So you can see how this kind of bends around.
Obviously I wouldn't want this flipped up.
This has to follow the path of water. Okay, I'm going to get this glued together.
One thing that I do want to mention, if you look at these fittings,
you'll see that they're kind of beveled on the outside.
You probably won't be able to see it very well,
but there is just a little bit of a bevel.
The reason that's there is as you go to make your connection,
you'll put the glue inside the fitting and you'll take your pipe and you'll
push it in and then you'll turn it about a quarter of a turn.
But that bevel's there to make sure that as you push in this pipe,
it doesn't push your glue out of the way.
And so whenever you make cuts on pipe,
whether it's the ABS or whether it's the PVC, the white PVC,
what you want to do is put a little bit of a bevel on the cut pipe because it'll
act like a knife if you just leave it straight and push in and it might glue,
it might not.
But what I do is I just take a regular file and don't go crazy with it.
Just file down enough to where you can get that sharp edge off and you just
kind of feel a nice round corner.
The glue I'm using is an all purpose glue for the ABS.
You never use their purple primer or the clear primer for the white PVC.
It's absolutely necessary to use that PVC primer.
So all you can do is just put some glue in the fitting and don't go real crazy.
You don't really want this puddling up. Same thing on the other side.
Take your fitting, just do a quarter,
about a quarter of a turn and just hold it tight. Okay.
So it's made a good connection. Okay. For the vent, for the air actuated valve,
I have the four inches up to this fitting that's threaded in the top.
These are actuator valves. All of them are, they're all threaded.
And what I'm going to seal it up with is this great white pipe joint compound.
Mine is white and purple because the stupid purple primer in my toolbox leaked,
but the bottle is just completely white and this stuff is super messy,
but just take enough to really coat the threads because keep in mind you're
doing this because you're trying to seal off the sewer gases and just carefully
thread this in. Keep in mind this stuff's all plastic and it all will break.
See I'm kind of finished with a just kind of a ring there as I finished up.
So I know I definitely got all the threads sealed up.
So here's the S-trap I'm going to be replacing.
My new pipe is going to come in here and that P-trap finagle that around to where
it goes in to this pipe here. So since this is a trap,
obviously there's going to be water up to the highest point.
Just put a bucket under the pipe. Okay,
so before you start gluing stuff together,
you want to try to figure out where this is going to fit the best.
These new traps, I mean they'll move,
but sometimes you got to get really creative here because of how close the pipes
are together and you might have to,
they make different fittings and elbows and things to get over to the pipe.
And so if I'm going to put this here,
I might do something like this and then elbow it back into the pipe there.
The pipe I'm going to be connecting into is pretty dirty.
So I'm going to cut this off and then make a cleaner that I'm going to put on
there. Um, a lot of people probably say to use it all the time. I don't,
if I use new pipes, I usually don't use the cleaner.
I'll use the primer if I'm working with a white PVC or if I'm working with the
ABS, I just make sure the ABS is clean.
There's a bunch of debris and stuff on it.
But in this case where there's actually garbage, I'm going to use that cleaner.
Instead of hack saws, I went to Lowe's and bought this.
Use it just like a regular, I guess you just use regular saws,
all blades for it. It's just on screws. You can put your blade in here,
screw it down.
But this is really nice because it'll fold up and I just throw it right in my
plumbing kit. So whenever I have something like this,
just have a blade in there and just cut the pipe.
And you want to make sure that these cuts are pretty straight.
Let's clear cleaner. It looks like you want to clean past where you're going to
glue. I mean, I've got a lot of this stuff,
so I definitely want to get this pipe as clean as I can.
So usually what you'll see in the kits is just the P-trap like this and it'll
stop here. And under ideal circumstances, that's all you would need.
They also sell 45 degree angles and nineties and things like that.
So I just put a 90 on here. So I'm going to, it's going to look like this.
The pipe's going to go in,
have to go through the trap and then come back out and go out into the drain.
Yeah. And even the best people make mistakes.
So where I had this lined up, I thought it was going to work pretty well.
And it looks like it's not going to, it's going to be just short.
It looks like it's going to work, but it won't.
So I have to put an extension on.
It'll take it further into this portion of the trap.
And then obviously to connect these,
stick the screw piece and take your gasket.
And you do want to get these pretty tight,
but while you're putting all this together,
don't tighten everything down real, real tight.
I'm going to leave a little bit of wiggle room so you can get everything to sit
just the way you want it. Okay. So just kind of get everything to where,
just kind of sit.
So there's no pressure or anything and then tighten up this fitting first.
Because remember, this is where the water's going to fill up.
And if you're going to have a leak, it's most likely going to be here.
That's tightened up.
And after that you can go ahead and crank everything else down.
I test these.
The first thing I'll do is I'll fill it up and let the water run for just a
minute.
And then that'll fill this trap up and let me know if I have a leak here.
So I'll start with that. Okay. No leaks there.
But to test all the pipes down there, what I'll do is I'll plug the sink,
fill this up about three quarters of the way full.
Then I'll pull the plug and let the water rush through and see if I have any
leaks. If there's no leaks,
then you can be pretty confident that you're good to go.
Okay. I think we have enough water in there to give this a try.
I'm going to pull the plug while all the water go down.
We'll just check for leaks. I don't feel any leaks.
So I think we're good. And a lot of times what I'll do,
I'll put a paper towel down and I'll just ask the homeowner just to keep an eye
on it for a day or so. See if there's any drops, but I think we're good here.
I also don't know if you heard that sound,
but you can hear that air actuator valve work.
It was kind of that sucking sound or whatever.
So if you do have any other traps or anything that you need to repair,
or if you happen to drop a ring down or something, you can see how those,
how those fittings come apart and you can get your ring out or whatever you
drop down into the P-trap.
Just make sure you have a bucket under there,
obviously cause it's full of water and you know that now.
And so try to apply some of these principles to other things around the house.
It doesn't have to be just strictly for what I showed in this video.
So we appreciate all of you that have subscribed and we love interacting with
you in the comments on YouTube.
And of course we have our email address. If you have any specific questions,
we'll absolutely get back to you.
I love teaching people and love helping them out.
So if you have any questions, feel free to email me. Thanks for watching.
