POLARITY MATTERS! Shocking - but true (pun intended)!
For many years, I thought it didn’t matter how you wired a table lamp, just as long as you got the wire securely affixed to the terminal screws, you used an Underwriter’s Knot, and everything was tucked away so nothing shorted out.
It turns out, there’s a bit more to it than that, and that “bit more” REALLY matters. Robert Ibbotson, who I met at a Woodsmith® Workshop in Iowa, told me about what’s overlooked many times, and that’s POLARITY. I was able to put his insight to use when I needed to rewire a lamp. Thanks, Robert!
To be honest, what I’m going to show you is right there on the product package when you buy a replacement light bulb base. Yep. All of it. But if you’re like many people, we don’t take much time to look at directions, especially if what we see looks like it needs no explanation.
The basics are you need to install the new part with the correct polarity and you need to assure that any tugs on the lamp cord are resisted by a knot in the cord under the lamp base, NOT the terminal screws. We’ll show you the knot in the video, but let’s explain a bit about polarity.
Lamp cord has two conductors, one that is designed to be “hot”, and the other is the “neutral.” To designate which is which, the hot side has a smooth surface, and the neutral has a rib. It’s not that easy to see, but you can readily feel it when you handle the cordage. The ribbed side will get wired to the silver terminal, and the smooth (hot) side will get wired to the brass-colored terminal. Of course, to have this work correctly, if you are rewiring the plug end as well, you’ll need to follow the same wiring protocol. Wiring it this way will greatly reduce any shock hazard once the lamp is plugged in. That’s because the electricity goes to the switch in the lamp base FIRST. This means that when the lamp is off, there is no electricity present in the base, or the shell surrounding the threads of the bulb. It’s “hot” only at the bottom of the bulb, where it’s very difficult to touch. If it’s wired with the neutral to the brass, and the hot to the silver, then the shell around the lamp threads are energized, with the circuit “waiting” to be completed at the base. The risk of YOU completing the circuit by grasping the shell is greatly increased. That’s not a good experience. Manufacturers provide a cardboard sleeve in between the inner threaded and outer shell. The outer shell is made of metal as well, typically in nickel, chrome, brass or deep bronze color. It is both decorative and structural. Because it is metal, it also conducts electricity. So, the cardboard sleeve between the inner and outer shells is another level of protection to reduce the risk of shock. So, be sure to get it safe, and right. For the protection of those around you, as well as yourself!
Sure, you can either discard the lamp or take it in for repair, but why? With what you've learned, you can JUST DO IT YOURSELF!
Hey, Dirt Farmer Jay here from DirtFarmerJay.com. Today I'm going to show you a quick little video
on how to correctly wire a table lamp. Now you may go, duh, there's just not much to it. How
wrong can it go? Pretty wrong. There's a little thing you got to take into account called polarity
and I'm going to show you how to get it right so it's done quickly and safe. Stay tuned.
Well, if you're like me, you like to actually repair some of the things that are around your
house and from time to time these lamps wear out. The rotary switch in them, if it's a switch type
like this lamp is, just over a period of time finally wears out and gives up the ghost. And
at that time you can either pitch it in the garbage or you can do something cool and repair it
and give it a second life. But do you know that most people don't know that lamp cord
has polarity? What is polarity? Well, polarity is what side is the hot or is energized and what side
is the return loop of the circuit, the neutral. And lamp cord has polarity. Now you can find it
really easily because there's a little tactile marker on the lamp cord itself. If you rub your
thumb across the cord, you'll see that one side is smooth and the other side has a little rib or
ridge that's been molded into the covering. The side that has the ridge is the neutral
and the side that is smooth is the hot. So why does polarity matter? After all,
on a device like a lamp, if you turn it on and the light comes on, everything's good, right?
Kinda. Here's the problem. Envision this. If you have a device in your house, let's suppose
it's an air conditioner or a washing machine and you have wired it so that the power
runs through the whole device and the last place that it stops at is the switch, either turning on
the air conditioner or turning on the washer. And then when you turn that on, everything happens.
That means the whole device is energized and it's possible that you can ground to it or you become
the switch, which is a really unpleasant circumstance. The way that's solved is making
sure the polarity is correct, that the hot side, the energy size of the circuit goes to the switch
first, and then once the switch is turned on, electricity flows through the device, in this case,
the threaded base and the light bulb itself, then out and completes the circuit. And risk of you
actually taking in a current is greatly minimized. So let me show you how that actually works and how
to correctly wire that when it comes to wiring a lamp or rewiring a lamp. All right, so let's
suppose that this is your lamp right here that you need to repair. So the first thing you need to
do is remove the harp, which supports the lamp shade, and that's done by moving up these two
retainers right here. You're just going to move them up, squeeze this together, and when you do so,
now you're left with the base, the retainer that holds that, as well as the lamp base where the
threads and everything hold the bulb and the terminals inside are here. The first thing you're
going to do is loosen this up right here. There's a set screw. You're going to start to undo this.
If you need to give a little bit of slack with a cordage from down below, you can usually push
that up through the bottom of the base of the lamp stand, and now you're ready to undo this.
Of course, what I do is I remove the light bulb right at the beginning also, so it's not in danger
of getting broken as we service it. So the first thing you can see here in this shot is that I've
pulled the wire up through, and we have untightened or unloosened the terminals of the defective
lamp base, and now we have bare wires. Of course, it almost goes without saying, but just to be safe,
make absolutely sure that you've unplugged the cord so you're not working with energized wires.
Now, once you have the wires out, make sure that the underwriter's knot is intact, and you can see
this underwriter's knot. I've tightened it up, and there's a great little diagram that most every
manufacturer provides on the back of their packaging, as you can see here, that just shows
you how to do the underwriter's knot. Its purpose is to assure that if the cord gets pulled, that any
kind of strain is placed on the knot at the base of this whole holder here rather than on the terminal
screws so that you don't end up with the terminals coming loose. So don't bypass that step. Make sure
that you put the underwriter's knot in there. Now, you'll notice here that there are different
colored terminal screws. You can see this one is brass, and brass, the protocol for electrical
devices, at least in the United States, is the brass colored screws are for the hot side where
the energy will flow into the device. You can see here that brass screw and the plate that it goes
into, but where does it go? Well, let's rotate it on the end, and you can see in the bottom of the
receptacle where the threads are going to be, a isolating brown tab with the metal tab that's
going to end up contacting the bottom of the light bulb when it's screwed in. This is the first place
electricity is going to flow in, and notice that it's also the hardest to touch because it's at the
bottom of the receptacle. So that's our first safety feature. So black to brass or hot to brass
is the nomenclature you're going to use or the protocol you're going to use. Now, notice here
you've got a silver screw. That silver screw, if you rotate it on the end and look at the bottom,
you can see that there is a rivet that goes through the bottom of the base, and now on the
other side, you can see outside of the plastic tab that's hot, you're going to see that it connects
to the whole threaded shell that is going to contact the outside threaded part of the bulb.
That's the neutral side, and once the switch is turned on, electricity is going to flow through it,
illuminate the bulb, and return the circuit. Notice that that means the shell then, if you've
absolutely correctly wired it, is never going to be hot or a danger of you touching something energized
unless the switch is on. Now, after we've wired the lamp base correctly, as you can see here,
all the wires are tightened to the terminals. Always try to get at least three-quarter of a
wrap around each terminal. Tighten them down firmly, and then you're going to reassemble
the whole unit back together. You'll see here that there is a cardboard sleeve that is inserted
between the metal threaded part in the bottom or the inside of this whole area and this outside
cosmetic shell. Again, another safety feature to isolate something that could be energized and you
to keep you safe. After you've reassembled everything, tightening the core down at the
bottom, making sure the knot's at the bottom, everything fits well in here, and you reinsert
the light bulb, you can see I tested it just to make sure my work was correct, and it was,
the bulb illuminated just fine, and this is a three-way switch, so I ran it through
to make sure that the dim, the intermediate, and the brightest all worked, and it did.
Well, there you have it. Polarity is important because you want to keep people safe, and I want
to give credit due to my friend Robert that I met at the recent woodsmith workshop in Des Moines,
Iowa. Robert and I had several conversations. He's another maker, craftsman, lifelong learner,
and he brought up to me the idea and said, Jay, are you aware that a lot of people are not aware
of polarity and that it's important to get it right, and he walked me through it, and I've
since used it, and I want to give a call out to him. Thanks for the great idea, Robert,
making sure that we're doing this correctly and helping us get the word out. If you found this
video to be helpful, why don't you like it? And better yet, why don't you subscribe to our channel
and be sure to ring the bell, because when you do, you'll get all the notifications immediately
when a new video episode comes out about the home, the garden, Maggie's Kitchen, or great product
reviews you can use around the home and garden. Until the next time, this is Dirt Farmer Jay
from DirtFarmerJay.com.