The One and ONLY Workbench You Need In Your Garage

Skill Time
40 followers
8 Video Views·Oct 30, 2022
Face it, you don't have a big enough shop.
So maximizing the space within your shop or garage
is a really big deal.
I work out of one half of a two-car garage.
So a lot of you are in the exact same position
that I'm currently in,
where my wife parks on that side of the garage,
my tools park on this side of the garage,
and my truck parks on the driveway.
So if you have limited space in your workshop or garage,
this is definitely something
you need to take a look into
because it combines a workbench with an assembly table,
a miter saw station, and a table saw outfeed.
So let me show you what I'm working with.
So when I was building this, I had two goals in mind.
The first was to have my miter saw part of this,
and the second was to have an assembly table
that was perfectly flat.
And the only way that I could come up with
to combine those two was to have a flip top.
So the first thing that I wanna show
is actually how this folds open.
This pulls off, it's just an insert,
and this guy folds all the way up.
So my miter saw is 3 1⁄2 inches tall,
so I made the base of the flip top
also 3 1⁄2 inches deep.
So now the miter saw is flush with the workbench.
So it means that if you're cutting long stock,
you'll have two feet supported
on either end of the miter saw.
So I have a four foot level here,
and it perfectly glides across, barely nicking it.
I also made this opening big enough
so that I have access to all of the different angles
on my miter saw.
So I'm not limited in capacity
of which angles I can cut and whatnot.
And that also goes for a compound cut as well.
So it can both turn and tilt
to every angle that it's capable of.
So with the miter saw folded down and the insert in place,
you have a three foot by six foot workbench.
Now this is a game changer
when you're building something super large.
You don't have to build it on the floor
unless it's really big.
Most furniture, if you're into building furniture,
if you're into DIY projects,
this is gonna be more than sufficient
for almost any DIY project that you're gonna do.
Now a big pain point for me
was cutting full four feet by eight feet sheets of plywood.
And I wanted to address that with this assembly table.
So if you take a look at it,
you'll see all of these grooves all throughout.
I just cut my sheets of plywood right on top.
I set the depth so it's only ever taking out
about a 64th, maybe a 32nd of an inch.
I have two sheets on top of this that make up the bench top.
There's a half inch layer of OSB,
and then there's a half inch layer of MDF.
And I'm actually gonna be changing out the MDF
to show you how easy it is.
A big plus of having a sacrificial bench top
is that I also don't care about it.
You can see that I don't treat it well.
I paint on top of it, I cut on top of it,
I drill on top of it.
You can see those holes.
And once a year, I just take it off
and put a new sheet of MDF down.
Now another reason why this is so efficient
in my small garage is because I put it on casters.
So when it's not in use,
I typically have it up against this far wall here.
Now each one of these four casters
has a locking mechanism on it.
And once you pop them off, you can roll this thing anywhere.
Then all you have to do is step on top
of the locking mechanisms.
You don't even have to do all four wheels.
I typically just do a minimum of two.
And it's totally locked.
And the last reason why this is the ultimate
small garage workbench is the storage.
Now I have this thing absolutely packed full right now.
On the right side of it, I keep my air compressor
as well as a retractable air hose attached to this.
And I also keep some of my lighting equipment.
And on the other side, I keep all of my tool bags
as well as a full set of automotive tools.
Because at the end of the day, this is my garage.
So it's where I keep all my tools,
not just woodworking stuff.
This is just another reason why this table
is perfect for a small garage.
It can store so much while still maintaining
all of this functionality.
So now that I've given you guys a tour on this,
I'm gonna show you guys how to replace the top
with a new sheet of MDF and how easy this process is.
Okay, so the very first thing that we did
was lay out our four by eight sheet of half inch MDF
on top of the assembly table.
And then we rough cut it about an inch wider
than we actually needed to fit all the way around the edges.
Now there are tabs in the opening
that the insert sits on top of.
And those were a little bit lower,
so the previous insert, I had to have some spacers.
I'm gonna get rid of that
so it's just totally even on the top.
So I'm gonna pull out those inserts
and I just use a pry bar to rip them off.
And then I use a hammer to hammer in
all of those finish nails so that they're out of the way.
So then I can pry off the top
and this is only held down with finish nails.
So these are 16 gauge finish nails.
It's very easy to just pry this off and throw it away.
It's important that there are no nails
sticking above the surface.
So make sure that you find any stragglers
and hammer them down below the surface.
With the MDF on top of the table,
I then traced all the way around underneath
to get the exact profile of the table.
So that'll tell me where I need to cut.
So after tracing the opening on the inside,
I flip it over and I can now cut that opening out
using my circular saw and the Kreg AccuCut jig.
So I cut both sides straight and then I do a plunge cut,
being sure to stop exactly where the line is
because a circular saw blade won't cut all the way through
like a jigsaw blade would.
So after finishing those cuts,
I flip it over and finish it off with a pull saw.
Next, I need to add the supports for the insert.
And I do this by adding some super glue
onto these plywood strips
and then I'm gonna set them in place
and actually glue them
to where they're touching the top of the MDF.
Then I'm gonna come back with the finish nailer
and throw in five or six finish nails
to really strengthen this up.
Then a final step is to round over all of the edges
and this is really not necessary.
If you don't have a router, you can totally skip this step.
This doesn't add any functionality.
I'm just doing this because it looks a little bit cleaner
and it's not going to catch as many things on the edges.
So that's the whole process of replacing the top.
It's really simple and easy.
It only took me an hour or two
and that's with me filming.
It has so much functionality
for the amount of space that it takes up.
And the fact that you could break down full sheets
of plywood MDF right on top
makes everything so much easier
when you go to do a project.
You don't have to worry about marring this up.
I paint on this, I stain things on top of this,
I drill into it, I cut into it with my saw
and it just doesn't matter
because at the end of the day, it's MDF
and it only takes an hour or two to replace
and I do it once a year.
And it is really nice to have a workbench
that you do not care about at all.
If it gets dinged up, scratched, painted, doesn't matter.
If you have any questions about the build process
or about this assembly table in particular,
go ahead and leave a comment
so that I can answer those questions.
And I know I'm going to get comments
about the finish nails being in the MDF
but using that nail set,
we set the nails a quarter of an inch down into the MDF.
And when I'm using the circular saw
to break down sheet goods,
I'm only ever cutting maybe a 64th,
occasionally a 30 seconds of an inch below the surface.
So I'm never going to get close to touching
any of those finished nails.
If you're interested in any of the tools
that I was using throughout this process,
I'll have links in the description
and you can check those out on Amazon.
I do a lot of home renovation, DIY,
and beginner woodworking videos.
So if any of that interests you,
go ahead and hit subscribe to my channel
and hit the bell notification
so that when I do release a video,
it notifies you so you can watch it.
So that's it for this one.
I'm Clayton, The Weekend Builder,
and I'll catch you in the next one.
