DIY Mobile Workbench Compact Woodworking Station Miter Saw Table Saw Planer Small Garage

That Tech Teacher
94 followers
66 Video Views·Dec 10, 2022
All right, today what we're starting is what I'm calling my ultimate all-in-one
mobile woodworking station workbench for a small garage.
And I think it's going to solve a lot of my problems.
All right, so the problem that I have is I've started investing in some nicer tools,
I just don't have a place to put them.
I'm working in a smaller two-car garage and this back corner of the garage
is the only place that I have to store stuff.
So stuff's piled on top of each other and it's hard to get to, it's hard to maintain,
and then it's no, you know, it's harder to get motivated to do projects.
So I think I've come up with an idea, a way that I can make a smaller workbench
that would fit in probably a lot of people's garages,
that not only holds and stores all the tools,
but it's a one-stop shop mobile woodworking station
where everything's self-contained and you use them right in the workbench.
So I got to get this stuff out of here and then I'm going to start building.
All right, so the design I came up with is roughly 32 inches wide by about eight feet long
and it has three built-in locations for the miter saw, table saw, and planer.
This workbench is mainly going to be built out of 2x4s
and when I'm building a project like this where you're actually going to see the wood,
I like to invest in a little bit higher quality wood.
So these are the Douglas fir 2x4s and they cost a little bit more,
but I think it's worth it.
The grain pattern's a whole lot straighter and they look a whole lot nicer
and they don't have as many knots.
One thing that I like to do that you don't necessarily have to do
is I run them through the planer.
I run them through each direction and remove about a sixteenth of an inch off each side.
And really the main reason I do this is just so I have a nice clean work surface
on each side and I square them up.
Technically if I had a jointer it would help me do this a little bit more precise,
but the planer does a great job.
Then once everything's milled to size,
using my cut list I measure out and cut the pieces for the frame.
I try to cut as many of these at the same time as I can to be as efficient as possible.
Then I always like to lay things out just to make sure everything looks correct.
Then before I start assembly I have to make a modification
to the top rail of the front of the frame.
I need to actually cut like a little ledge out of it
so that the table saw can sit down into the frame.
To cut the straight part of it I use the track saw
and then to finish it off I use the jigsaw.
Then to attach all the pieces of the frame together
I use a square to help me hold the boards in place.
Then I pre-drill the holes to keep them from splitting
and I also found out that it helps when you're screwing the two boards together
it keeps the boards from moving around so much.
And I repeated that process for both sides of the frame.
Once I was done with both sides of the frame
I stood them up next to each other just to make sure everything lined up like they should.
After making a few more cuts I now have all the interior boards that I need
to attach the two frames together
and I'm going to do this using pocket hole screws.
I really like Craig's pocket hole screws because they're so strong
and the way that we're doing this
we're not going to be able to see any of these fasteners
from the outside of the workbench.
Depending on how the boards are going to be used
I'm either putting pocket hole screws in the edge of the board
or in the faces.
Now before installing any of these boards
it would be a really good time to go ahead and put a few more screws
in each one of these joints to help strengthen them up
but before I put those screws in
I always like to test fit the boards that I'm going to be putting in place
so that none of the pocket hole screws run into any of the previously installed screws.
Then I go ahead and screw these together
and sometimes it'd be nice to have an extra hand
or somebody to help hold this up for you.
Then I headed over to the table saw to modify two of these boards
and basically all I'm doing is cutting a rabbet out of the top of these
and this will connect to the table saw ledge
and something that the table saw will sit into.
Then after fitting the table saw in place
I realized that the right side and the left side are not symmetrical
and I didn't account for that in the planning of the project
so I just had to make a modification to the top rail
and then the vertical piece that connects into it.
Once those two things were notched out for the legs
and then for the little connecting rail from front to back
we were good to go.
Then heading over to the miter saw station
I installed two more support rails
one on each side
then I put in a front rail
made sure I checked my measurements
that it was the exact size that I needed
then I screwed that and two other support rails in
to hold the miter saw.
When test fitting the miter saw
I found out that I'm about two degrees short
on the left hand side and on the right hand side
so I might have to do a little bit of clearancing
but it fits and it looks pretty good for now.
All right so it's really starting to look like a workbench now
at this point I know that the miter saw
the table saw and the planer
the three big things that I wanted in this workbench all fit
now I can go back and reinforce this frame.
To do this I'm going to measure and cut boards
to fit in all the openings in the frame
I want these boards to be extremely tight
to lock everything together.
Then I'm going to use Titebond 3 wood glue
I've just had really good luck with this stuff
and it's indoor outdoor use and extremely strong
I'm going to put a nice coating on either side
clamp these together
and then pre-drill and screw them all together.
This is probably the part where I went wrong
probably would have been easier just for me to leave the glue
and then chip it off later.
Then when we get behind the table saw
I'm going to go ahead and put a horizontal piece
underneath the remaining legs of the table saw
this is not only going to help hold up the back of the table saw
and support it
but it's going to lock the two verticals together as well
then I'm going to brace this
just like I did all the other parts of the frame.
All right now that the workbench is fully assembled
I can go ahead and start installing the casters
and I'll be honest with you
I've never used a caster like this before
I saw somebody that highly recommended these on YouTube
and figured I'd give them a try.
I bought these on Amazon
and to be honest I think these are a cheaper version
of a really expensive caster
but so far they look to be pretty well built.
So these are a leveling caster
and the whole idea behind them is that they fully rotate
and there's a wheel obviously on there
that allows the workbench to roll around
but then when you want to lock it in place
there's that dial that you can turn
that will lower that rubber foot
and lift the caster and whatever it's on
off of the wheel.
This seems like it's going to lock the workbench in really well
and or potentially help me level it on an uneven surface.
To install the casters I lined them up under a main vertical piece
marked out where the holes were going to go
pre-drilled them
and then screwed them in with a one inch lag screw.
All right so I repeated that same process five more times
and I have a total of six casters on here
so two on either end
and then two in the center
and this thing rolls around really easy.
I was concerned about the smaller wheel size on these casters
but even on the carpet on this side of the garage
it rolls around pretty easy
on the other smooth side of the garage
it rolls around with no effort at all.
And then the other cool thing about these casters
is it has that other piece that you can adjust
so that it clamps down
and it really locks the workbench in place.
Now these casters aren't perfect
but with all six rubber feet down
and the wheels up off the ground
this thing's not going anywhere.
I've never seen a lockable caster
be able to hold something this tight
so it's not ideal that you have to get down there
and unscrew those things
or screw them back up in
but man when they're down
and if you want something sturdy
it looks like these are going to do a pretty good job.
Then back underneath the table saw
I installed two more support boards
and a set of heavy-duty drawer slides
to help me install the planer.
To do this I used screws
and those same lag bolts.
The only problem you may run into
is the head of the lag bolt might be too big
and the locking mechanism might hit on that
when it slides by.
So I had to make a minor adjustment
still used lag bolts in some places
just not the whole way.
Then using some 2x4s and pocket hole screws
I created a basic shelf
to attach the inside drawer slide.
With the planer in place
I slid it out to make sure
that it didn't hit anything on the table saw
and then I raced it all the way up
to see how thick I could plane things
before I ran out of space
underneath the table saw.
The big thing was being able to use the power switch.
Then I screwed it down to the shelf.
Now that everything's in place
I can see that I might have a potential problem
with dust collection
in that back board
that's supporting the back of the table saw.
It's also hitting on the outfeed table
of the planer.
And even if that board wasn't there
the outfeed table would still hit
when I'm trying to slide the planer out.
If you have a solution for this let me know
but I'm not so much worried
about the outfeed table of the planer
because it's so easy to take off
and then put back on
that I'll just take it off
and put it back on
every time I use the planer
and the one on the front works perfectly fine
so I think we're going to be okay there.
Also I haven't made up my mind yet
whether I'm going to be using the planer
when it's still underneath the table saw
or I'm going to slide it out
every time to use it.
Then back on the other side of the workbench
I'm going to have an overhang
because of the way my garage wall is
so I installed these supports
with some more pocket hole screws.
Then I brought over the piece for the top
and for right now
I'm going to use a piece of
three quarter inch maple plywood.
The factory edges on this plywood weren't great
so using a square I marked out a square line
and then made a nice clean cut
with the track saw.
Then once everything was lined up
I went underneath
and marked out the bottom dimensions.
This would have been a really nice time
to have a trim router bit
but the kreg track saw worked pretty well.
After that I cut a half inch thick piece
of maple plywood
for the miter saw to sit on.
This is only temporary
it'll have to be trimmed and shimmed later.
Then with the top back on
I test fit the miter saw
in its exact location
and I used a pencil
on the farthest back part of the miter saw
to help me draw an arc
where I was going to cut this top piece.
I did this from multiple different locations
so I came out with multiple different arcs
trying to find the farthest point out.
Then I extended the lines
where I couldn't and traced the bottoms.
I cut the straight parts with the track saw
and then after building up my courage
I cut the curved part with the jigsaw.
After a few adjustments
it came out looking like this
and the saw rotates back and forth
with plenty of room to spare on both sides.
Then finally back over at the table saw
I needed to install the front and rear rails
to support the fence.
I did this by installing the original hardware
back into the front of the table saw.
I used a level
not to make sure that it was level
just to make sure that everything
was lined up and flush.
I drilled holes
and installed new longer bolts
and bolted the fence
to the rails of the workbench.
I also relocated the on-off switch
a little bit closer
and tested to see if the fence worked.
All right at this point
we can almost start using the workbench.
Really the only thing we would need to do
is permanently attach the top
make sure I shim it up
so everything's flush
with the top of the table saw
and the miter saw
to make things as accurate as possible.
You could add a piece of plywood underneath
to add a little bit more storage
and then maybe a power strip
to plug all these tools in with
and you could start using it
but that's not where we're going to stop.
In part two
I'm going to add a bunch of storage
and dust collection
and I'm going to do it a little bit differently
than I think most people do
and then in part three
if there is one
we're going to go ahead and add
maybe even a few more tools to this
to make it even closer
to that ultimate all-in-one
woodworking mobile workstation workbench
that I'm trying to build.
But I would like to hear your thoughts
of what machines do you think
need to go in this workbench
or what would you like to see
kind of in the future for this.
One thing that I would like to note
is these machines that are in here
are not the smallest
and most compact versions
of the machines that we could have bought.
I tried to invest in higher quality tools
for example the table saw
that is a still a contractor's great saw
but it's not one of the cheaper ones.
It is a cheaper table saw
and for the DIY homeowner woodworker
I think it's a great saw
and the reason that I went with this one
is because of the fence.
It has a cast iron top
and it has a really nice fence
that helps keep things
a little bit more accurate.
When you put a good blade on here
combined with that fence
I think you're going to get
some pretty good results.
The delta planer
that I have on the bottom there
pretty much most people
I think would agree
that's probably about the best
benchtop planer
that a homeowner or DIYer can buy.
Yes there are bigger
better tools out there
but I think for the value
and the size that you get out of that one
it's probably about as good as you can get.
And then down on the other end
I didn't get into any of the fancy miter saws
that like scissor action or fold up
that would have been really nice
to save some space
but this one I really have had
good luck with.
I like DeWalt miter saws
and corded tools.
This one's a double bevel
or maybe it's only a single bevel
but slider miter saw
and I've had really good luck with it.
It's a little bit bigger
so all these tools
were not exactly the most space-saving tools
but I think we were able
to fit those pretty efficiently
into what I think is a smaller workbench
and the reason that I think
it's a smaller workbench
is because most of the workbenches
that I see on YouTube
are four by eight.
There's no way that I have room
for a four by eight workbench
in this small of an area.
So this one's right around 32 inches wide
and it's a little over eight feet long
making it fit in that position
in my garage back there
almost perfectly
and it's going to have a ton of storage.
When I want to use my tools
you just wheel it out.
There's no setup.
I don't have to flip anything up.
I don't have to lift any tools up.
I can use them all right where they are.
The most setup that I'll have to do
is rotate the miter saw to 90 degrees
or whatever angle I'm looking for.
I can use the planer
if I'm planing stuff
I think it's under four and a half inches
in thickness.
So in theory I can use the planer
right exactly where it is.
If I have to go over
four and a half inches in thickness
I slide it out
and you're ready to go.
So I really like where this is going.
I'm looking forward to the future
of what else we can add in here
and what you guys are going to think.
If you like this project
and want to see where I'm going with it
I encourage you guys to subscribe.
Other than that
I hope to see you guys in another video.
