Pro Tips for Fast Square BASEBOARD INSTALLATION - To Cope or Not To Cope

Machines Co.
49 followers
4 Video Views·Oct 29, 2022
Hey what's up guys and welcome back to the channel. I was recently working and I was
getting asked via DMs on Instagram how to install square edge baseboard and how that differs versus
a typical coped baseboard installation. In this video I'm just going to bring you alongside me
and show you how I go about my installation. Hopefully you can get some pro tips and tricks
and maybe add something to your workflow that'll make you faster and more effective. So my first
piece of advice, always use a headlamp. It's the most handy tool you can have for working in dark
places. In new construction homes there's never any lighting installed, so you're going to go
into a lot of dark rooms and dark closets. The headlamp makes life a lot easier. Next tip is
going to be on cut lists. I always have two cut lists in play. One is always clipped to my holder
on the saw. The other is in my tool belt. Whenever I walk up to the saw to start cutting a new cut
list, I'll take the cut list that's already clipped at the saw and put that back in my nail pouch.
The reason for this is it's really easy to forget your cut list at the saw all the time. Having two
eliminates that problem. I like these little notepads and I've got them listed in my Amazon
store under consumables I believe. I like to draw a nice straight line splitting the page in half
and then number it off. It gives you about 36 pieces. So I'll take measurements and fill out
that whole page, cut every piece, move them to wherever they go, start over and do it again.
36 pieces is a pretty good amount. Doing any more pieces than that and it can just get kind of
confusing. The number on the cut list is going to get written on the wall where the baseboard goes
and then it's also going to get written on the back of the piece of baseboard and that's going
to help me keep track of where all these pieces go. Let's talk tool belt setup. First thing you're
going to have is gauge blocks. These keep the baseboard up off the floor. Next thing is going to be
your gauge block, same thickness as the base for measuring base. Stud finder, love that Franklin.
Leica Disto D2 laser, best one out there. I've got my brad nails back here, inch and a half, 18 gauge.
My cut list or my 15 gauge nails and then my cut list is tucked back in here. Other side, got my
rubber mallet, that way I can beat things in this subjection. Glue, glue bot, sandpaper, 120 grit.
My pry bar, this is the best pry bar for baseboard and stiletto 10 ounce hammer,
which also is needed at times. Shameless plug here, easiest way to support the channel is to
utilize the links that are in the video notes or go to my Amazon store where I have lists of
the tools that you'll see me using here on these videos. It's a great resource for finding really
great tools that will help make you money and be more efficient. Here you see my laser, the Leica
Disto 2, highly recommend it. I've had a couple of them that I've broken due to my own neglect over
the years, but they hold up great and are extremely accurate. Pretty much a necessity for any kind of
trim work. So let's go over how to measure an entire floor of baseboard accurately whenever
it's a square profile. You'll see here this is a square edge five and a quarter baseboard,
eased edge on top, it's got relief cut on the back. So typically with baseboard you would always be
measuring from corner to corner and you would be coping the baseboard. But whenever you have a
square profile like this, you don't want to do that. Well you can't do that because you're not
mitering it. So I was actually just talking to a carpenter today who's asking me some questions
on how to install this. So I'll show you my workflow on how I do it. The first thing and
what's going to seem most obvious is that you can't measure corner to corner with this type
baseboard unless you're going to miter it or cope it. In my opinion this does not need coped, so we're
going to be square butting everything together, which means you always need a small block in your
bag of baseboard that matches the thickness. So what you're then going to do is you're going to
take your baseboard and you're going to use that as an offset block whenever you're getting your
measurements. So turning you around right here for example, I've got this piece starting out and
we're going to go around the room like so. My first measurement, this piece is going to need to go all
the way through to the wall, which it does. Now on my next piece I need to subtract the thickness of
this baseboard. So as I'm going around measuring the room what I'm doing is using that block
and shooting my laser down there and that gives me my measurements. So it's super easy you just
as you go around the room I take that measurement then I would actually move to this corner
and I would actually be shooting from here that way. Same thing I'd move down here
and then I'd shoot that way, so on and so forth. Now something I like to do, you're going to have
this situation throughout the entire house where the door is off of a wall and you have a narrow
piece of baseboard. Personally I always take my long piece and run that through
and then I install the small piece like so. The reason for that is if you install that this narrow
piece first the taper on the bottom of that piece of drywall is going to want to let this piece
kick the small piece kick in and it's going to be really hard to deal with that and what would
happen is you would end up with a gap right here. Whereas if you install this piece first
then this piece if it's kicked in on the bottom a little bit it's not a big deal because you're
riding up against here so it's going to be nice and tight. Whenever it comes to measuring outside
corners if you're measuring and you're looking at it from this angle you're not going to be
able to see the tape very clearly. So to get a good eye on it you actually want to move around
here and look at it straight in line with that wall and it's going to be a lot easier to see
what your measurement is versus if you're way out here trying to look at it at an angle. I've got
this upstairs done and I actually cut the main level base of base this morning. You see some
pieces laying around so that's not nailed on yet so let's go down there now and I'll show you some
things there. You'll notice here I've got pieces laying everywhere and you'll notice with each
piece there's a number written on the wall and it corresponds with the number I write
on the back of these pieces whenever I'm cutting them at the saw. That way it's easy to keep track
of the pieces and get them where they need to go. For me personally I like to cut an entire level at
a time. Usually that's about three pieces of paper on the cut list so usually 100 to 150 pieces of
baseboard. I'll scatter those to where they all need to go and then I'll strap up my knee pads
and nail them all off at the same time. If you're an apprentice wondering how accurate you should be
measuring baseboard I think you should be around 95 to 100 percent accuracy rate. Meaning if you're
cutting 100 pieces 95 of them should be correct at minimum. Typically for me I'm usually having
two or three recuts per floor. For whatever reason it's hard to reach that perfect mark but usually
I have a brain fart on one or two pieces where I add an inch or something dumb and have to go back
and recut those. But you should be able to get almost every single piece right. So notice over here
this wall and this wall are over 16 feet long. So when that happens I biscuit a splice in the center
butt joint it cut it a little bit long and snap it together. With a long wall like this let's just say
it was 249 inches. What I do there is I'll just cut one piece at 100 inches subtract that off at
249 then my next piece is 149 inches. Or if it was 145 and 7 8ths I could cut and I had a 100 inch piece
later on I cut it 100 inches and then cut the remaining on the next piece biscuit the two ends
and it's really simple and that way you're not losing your workflow running back and forth
to a wall cutting one piece and then taking the measurement on the next piece. It's real easy
just take the long measurement with your laser and then cut both pieces at the saw just like you do
the rest of the pieces. I'll tell you one tool that's an absolute must have for baseboard is this particular
flat bar. This one always lives in my bags. It's got a very narrow end and it works great as a
scraper but then also this thin hook on the end works great to hook in under the baseboard and
pry it so if you've got a gap at the bottom of your joint it's really easy to pry it back out
and then scissor nail it and that'll give you a tight joint. Lately I've been just walking around
and cleaning all the drywall mud off that would hinder baseboard installation in advance that way
as I'm installing I don't run into problems I'll just take care of it all at once. When you're
installing you've got to always have your eye looking out ahead to watch for globs of mud
otherwise you can really just run into annoying issues as you try and nail things off. Things
won't want to fit together tightly so it's good just to get things cleared off. If anyone's
wondering as far as nails go for baseboard I like to use inch and a half 18 gauge brads to
nail my outside corners and then any small pieces that might split with a larger nail
and then for the rest I use 15 gauge. Two inch long is typical for 5 8ths baseboard and then I'll
just load those up in my tool belt and go to town. One of the tools I'm most passionate about is these
pro knees knee pads. They are absolutely amazing for weight distribution on your knees. I'm 31
and I didn't do a good job of taking care of my knees earlier on in my career so I definitely
feel it in my knees and these knee pads are absolutely amazing. They really take the pressure
off your knee caps and distribute it across your shin bone. Great product I'd highly recommend it.
Any young guys out there watching take a word of advice from me and take care of your knees.
If you don't you're not invincible and you will feel it eventually. Now it's time to nail off. I
know there's a lot of fancy nail guns out there. I've used some of them and I still love my simple
and cheap Bostitch and Hitachi. These have been great for me and I've got no complaints. I also
highly recommend installing these hooks on all your nailers. Makes it really easy whenever you
need both sets of hands and a gun nearby. In my area we install flooring after baseboards so I
have to reference the print and see what flooring goes in which rooms and then keep the baseboard
up at the proper height. So for carpet it stays up 3 8ths and then for hard surface flooring I
want to be 1 8th inch above whatever the hard surface is. I always rip some scrap spacer blocks
just out of scrap material laying around on site and then I'll use that in the corners to keep the
base up off the floor at the proper height. So here you see me I'm just going around the room
start with one piece move on snap the next piece in so on and so forth. Usually I'll
try and get all the pieces snapped together and then nail them off all together at once.
Here you see the necessity of the rubber mallet. You're gonna have to bang on the
wood to get it where you want it to go if you're installing things tight. If you do that with a
steel hammer you won't see it on raw wood but you're putting dents everywhere in the wood
that'll show up after it's painted. So the rubber mallet is really a must for baseboard installation.
Whenever you're installing baseboard you have to be really careful with the pieces that you're
installing that will butt up against door casing. The reason is if it's too tight and you really
force it into place it'll push that casing inwards and it'll close the margins on your doors. So
whenever I measure my pieces I don't add anything for those pieces that butt into door casing.
I want them to be exact that way it doesn't mess with my door margins. Personally for me nailing
off baseboard is probably the thing I hate more than anything whenever it comes to trimming houses.
That's why I usually try to get in at framing stage before drywall and actually spray
marks on the floor where all my studs go. That way I don't have to be trying to find studs with a
stud finder or laying my tape on the floor to show me where I need to nail. I definitely
just flat out hate nailing off baseboard. This Franklin style stud finder is definitely by far
my favorite. I'd highly recommend that to anybody. It helps you see the bigger picture not just where
one stud is but you can also tell whenever you've got multiple studs packaged together
so on and so forth. So highly recommend it. But definitely the best thing ever for nailing off
baseboard is getting in before drywall and marking everything on the floor. The other
advantage to that is also you can mark water lines and other trouble spots to ensure that you're not
accidentally going to put a nail into something that you shouldn't. These days there's a lot of
hardwood being put into new homes and one nice thing to do whenever you're nailing off baseboard
is try and keep your bottom nail low enough that the shoe molding will cover it. It's just one less
nail hole then that could possibly show up and be visible after paint. Usually for short runs
of baseboard I'll just use my stud finder but for longer runs I like to lay out my tape measure on
the floor and then just use the red marks to go every 16 inches and put a nail where it needs to
go. One pro tip I would have for finding studs is use your eyes. Drywallers are not very good a lot
of times and a lot of times you can actually see some maybe nail pops or you can see the mud where
a nail has been spotted. The other thing to look for is electrical outlets. It's easy to look at an
electrical box and you can tell which side of that box the stud is on by the tabs on the side of the
box. So that's another thing to keep in mind especially whenever you're laying your tape on
the floor for a long run. I'll look for electrical boxes. I'll look for the stud whichever side it's
on and then I'll lay my tape on the floor accordingly with that and that usually works pretty good.
And then there are the joys of shooting a nail right across the top of the baseboard when you
get carried away. Pretty easy to set one like this. The worst are the ones that graze the top of the
baseboard and mess up the wood and splinter it off. So thankfully this wasn't a very big deal but
always good to take your time and do dumb stuff. Drywall is somewhat fluid. If you've got a piece
that's a little bit long, pull it back and give it a hard push and that'll actually maybe clear
the mud out of the way or dent the drywall a little bit and it'll fit. I like to cut all my
baseboard outside corners at 46 degrees. That seems to work well for keeping the outside corner closed.
Occasionally they still open up and in that case I'll use a steel object to burnish the edge
and then sand a little bit and you're good to go. The most common question I get regarding this type
of baseboard profile is typically the front edge of that baseboard has got a round over on it.
Usually a 5 32nd and people ask if they're supposed to cope that or not. For me the answer
is no. I remember going back years ago to one of my first houses that I trimmed as a subcontractor.
I took the job and I thought I had to live up to this insanely high level of carpentry. At that
point in my career I was extremely naive about the level of quality that was actually going into the
work in the trim subcontracting industry. I learned as I watched more and more carpenters
that there was a lot of subpar work going on but I also came to realize that I didn't have a good
understanding of what real value actually is. As a trim subcontractor I've got to value engineer
the job, meaning I've got to find the way that is going to be the fastest and most effective
while giving the most quality on the installation of any given product. So on a piece of baseboard
like this there's no added value to me in coping one eighth inch radius on baseboard that's not
going to be discernible. Same thing with a jack miter. There just isn't a discernible difference
and people don't notice that kind of detail. So it's better for me to put that labor into
something else that's going to give the client something that they actually want. Going back to
that house years ago where I was first introduced to this baseboard profile, the baseboard profile
going in that house was this same profile. So I thought I had to get real fancy with it and do a
jack miter that way that that top edge of that baseboard had a miter on the inside corner. So I
was doing the main level and the upper level of the house. Meanwhile an old school carpenter showed up
to do the basement because it was a large home and he was just budding everything together. At that
time he understood value a whole lot better than I did. In trim subcontracting if you're doing
something and it's not adding real tangible value that means you're costing yourself money or you're
or you're costing the client money. That takes details away from them that they could have had
because you're using labor on something that isn't necessary. So in my opinion coping that little
round over is completely unnecessary. I've done miles and miles of this baseboard and no one has
ever said anything about butt joints and the rest of my industry in the city people are installing
it this way too. Hope you guys enjoyed the video. Don't forget to hit the like button and drop me a
comment down in the comment section. Let me know what you think, any improvements I can make on the
video, questions, comments on things that you do differently or things that I can improve on.
I'm always open to suggestions. So until next time we'll see you in the next video.
