iPhone 7 Microphone Replacement Repair How To Change

Finger Family
30 followers
34 Video Views·Oct 28, 2022
"iPhone 7 microphone replacement. How to change the microphone in the iPhone 7. iPhone 7 bad mic. iPhone 7 microphone fix. iPhone 7 microphone replacement repair do it yourself and save a lot of money. iPhone 7 microphone repair DIY. I hope this video helps you in successfully changing the microphone in the iPhone 7. Smartphone repair do it yourself DIY is the way to go.
http://ebay.to/2i3Xk6t here is the best place I found to get a new microphone. It's the same part as the charging port flex since it's built into the same part.
http://amzn.to/2gwN1Gp here is a premium tool kit in the $28 price range that I recommend that is very well put together and has most everything you need"
Hey guys, so today I wanted to make a video to show you how to change the microphone in the iPhone 7.
So first you want to make sure your device is powered off. Next I'm going to use a screwdriver
size 0.8. It's a pentalobe size 0.8. And we're going to need to remove these two screws in the
bottom of the phone right here. So go ahead and remove those screws. Alright guys, so the next
thing I wanted to show you in this kit is a suction cup. You want to press down. Make sure
that it's sealed good. You want to stay close to the home button but not over the home button
because it will break the suction. So what we're going to do also is this really thin pry tool
comes in the toolkit. And what we're going to do is try to get right above this speaker right here.
We're going to try to slip in right here very carefully in between the frame and the screen
right here. As you can see it's starting to separate a little bit. Then we're going to use
like this guitar pick or something thin that you have that you can pry around all the way around.
I wanted to talk about there's a waterproof adhesive that goes all along the edge right here
and by doing this repair it could affect how waterproof your iPhone 7 is just to give you a
heads up. They're not readily available yet but there is some waterproof adhesive. I don't have
any right now to show you but I'll link to it in the video description that you can put back on
here when you put your iPhone back together and it should retain that waterproof seal. Like I said
they're not readily available yet. They're hard to come by but they'll become more readily available
as time goes on I'm sure. So I just wanted to give that heads up that it could affect the
waterproof of your iPhone 7. So next what we're going to do, I'm going to put a little upward
tension on this right here and I'm going to slip in right beside this thing here. I'll try to turn
it this way to show you and we're just going to carefully slide along here. We can remove this
thing once we got it started and we're going to cut through the adhesive here. Just come to this
top corner here. Then we're going to go and we're going to slide along this side here and now you
don't want to stick in too far right here because there's some cables right here where the iPhone 7
screen is attached. So you want to just slide up through there. It's starting to separate here as
you can see. So what we're going to do is we're going to remove this suction cup now and what you
want to do you can see is starting to separate like this. Now the top has some tabs that stick
under here so we don't want to just pry straight up. Also unlike other generations of the iPhone 7
the screen comes off and it tips like this. Like a book it doesn't tip up like it used to in previous
generations. It tips this way. So just to give you a heads up about that. But what we're going to try
to do is we want to bring this up a little bit and if possible we want to cut this adhesive in here
like this with this guitar pick or whatever you'd use. As you can see it's starting to separate
there and there's that tab I was talking about. So you get it down far enough where you can tip
it up like this. Then I'll set it like this so you can see. Then we should be able to just carefully
tip it up like that. Now next while you're holding the screen up like this just past the 90 degrees
you don't want to put too much tension on these cables to tear these cables here. And we're going
to use this screwdriver with a bit it's called tri-point size 0.8. Now sometimes the manufacturers
vary on the sizes but in this kit mine's called 0.8. So Apple just kind of had to throw us for a
loop and use a different kind of screw in this. So basically we're going to remove these four in
this shield right here. So go ahead and remove those fours. Now make sure to keep them in the
right order because they're different size you don't want to mix them up. So next after you
remove those screws just I'm going to use the tweezers. You can use your fingers for this
and just grab this shield and set it off to the side with your screws. Next I'm going to use a
plastic pry tool. You don't want to use anything metal for this. You can use a plastic pry tool.
Let's go ahead and remove that connector. Remove that connector and while we're at it let's go
ahead and disconnect the battery. Get that up out of there. So next under this shield right here
there's two screws we're going to need to remove as well. It's holding this cable in here down and
this is a phillips size 000. So you want to go ahead and remove those two phillips screws. Next
we're going to use the tweezers and remove this shield right here. Set it off with your screws.
Next you want to grab your plastic pry tool and you can go right under this corner right here.
Just carefully pry up that connector and the whole screen comes out just like that. Now since
we pulled the screen off here if you look on the edge here there's some adhesive residue here.
We'll want to go ahead and use the tweezers or something and get that all off of there. Once
you get it started it should peel right off. If this video was helpful to you I would appreciate
if you would give it a thumbs up and subscribe to my channel. That would help me out a lot.
Just to give you a heads up the charging port which is located right here. In order to replace
that we're going to need to remove this whole logic board here which is quite a process and
to get to this charging port here because there's a connector that runs under the logic board and
connects right here and that's why we need to remove the whole logic board to get to the
charging port. So it is quite a process but it can be done. So now to change out this whole logic
board motherboard right here. It starts here and goes up around. We're going to need to remove a
lot of different kinds of screws so we're going to just take it one step at a time and show you
how to do this. So let's get started. First of all we're going to need a phillips screwdriver
size 000. Also on some screwdrivers it's called 1.5 by 45. What we're going to do is remove this
screw right here and this screw right here on the opposite corners of this rear camera. So go ahead
and remove those. Now that you've removed those screws let's slide under this here. Get this shield
off of here and set it off with your screws. Next we're going to use a plastic pry tool or your
fingernail or something. Nothing metal for this. And slide under this connector right here and pop
it up. You gently pull up and the rear camera will pop out just like that. Next we're going to
use a phillips screwdriver and remove these two screws in this part right here. This phillips
screw right here and there's another one right here that we have to come in like this to get
and we need to remove that screw as well. So go ahead and remove those four screws. So now that
you've removed those four screws you can just grab this set it off to the side with your screws. Next
we will need to remove this screw and this screw. Then we can just grab this part set it off to the
side with our screws. Next we're going to remove this little clip right here with the foam piece
attached. Go under there and unclip this part. So make sure that's unclipped and out of the way.
Then you can use your phillips screwdriver and remove that screw in there as well. Next we need
to use our tri-point screwdriver size 0.8 tip and we're going to need to remove these two screws
right here. Next you can grab this shield and set it off to the side with your screws. Next we're
going to turn this sideways. Get in here to this connector. Gently pry this connector up. Now we
need to unhook these two antenna wires right here. So we're just going to unclip them by gently
prying up on them. Then we can slide them out from behind this clip right here so they're loose. Now
we're going to use a little flat screwdriver for this. Mine is size 2.0. Yours may vary a little
bit in size. And we need to remove this screw right here and this screw right here. So go ahead and
remove those four. Now next we're going to use our sim eject tool and we're going to remove the sim
card tray. Now next we need to remove this connector right here. So unclip that out of the
way. Now we're ready to lift this board out of here. We need to watch a few things. We need to
be very careful. So I'm going to use something plastic for this. You can just gently use your
finger or something. So we want to carefully pry up here and you want to watch this connector here
so it gets past there. Then as we're tipping this up we can kind of get it up past this right here
and then the whole board is free to come right out. So Apple designed this charging port in such a way
where we have to remove everything to get to the charging port. In generations past you didn't have
to remove the motherboard because the connector stopped down here but this they decided to run
it under the motherboard. That's why we have to remove the whole board to get to this because you
risk damaging things if you don't remove it all the way. So next we're going to use our Phillips
screwdriver. We're going to remove these two screws here, these two in the bottom of this,
and remove these three screws in this thing, and these two screws in this plastic thing for now.
We're going to leave a few of these in here for now. Go ahead and remove them out of this, this,
and this for now. And be sure to keep the screws all separate so you know how they go back together.
Now that you've got all those screws out, first we're going to just grab this plastic thing,
that part out of there. Set it with your screws. Next we're going to use our plastic pry tool here.
We're going to pry up on this connector right here. Then we'll grab this part and get it out of there.
Then we need to use something and pry up under this tape right here. We have to be careful not
to damage this. And you peel this tape up right here. Then you can just grab the loudspeaker,
pull up here a little bit, tip it forward, and as it comes out watch this antenna wire right here.
It's in this channel right here. You want to pop it out of this groove right here. Then this
whole speaker comes out. Then you want to go ahead and remove the rest of these screws right in here.
So now I'm going to turn this upside down so it's easy for you to see. So now we're just going to
carefully peel up on this. If you have to you can use something to pry with as you go. You want to
loosen the adhesive all the way. So next now that you've got this adhesive loosened pretty good,
right in here and right in here there's a Phillips screw that we're going to need to remove.
Next we need to unclip this little microphone right here and you have to unpeel this one.
This one's stuck down. So now that those are loose you can go ahead and grab this part and
the whole part comes out just like that. Now this charging port also has microphones built into it
so if people are having trouble hearing you on speaker or off speaker there's a pretty good
chance that this part is bad so you have to replace this whole part. Now you also have to
look if there's anything you need to swap over onto your new part. There's a little clip right
here is the only thing that I could see potentially that you have to swap over. Just check
and make sure if there's anything that is different on your part from the original that you can swap
over to your new part. So next grab your new charging port, set it down in here. Make sure
everything sits in there the way it's supposed to. So you can go ahead and get your microphones
down in place. Make sure they're stuck down the way they're supposed to. This one sticks down,
this one clips on. Make sure this one's tucked underneath the rubber part here. And let's go
ahead and put our two screws back in the very bottom right there. Now that you got your two
screws back in, make sure this is stuck down. Then we're going to grab our loudspeaker and go
ahead and connect this antenna wire in this top one right here where this metal part is. So go
ahead and do that next. Next before we get this loudspeaker down in our way let's go ahead and
put these three screws back in here. Next grab your loudspeaker, set it down in here. Make sure
that it gets tucked in right down here where it needs to go. If you see that your screw holes
line up then you're all set. Then go ahead and put your screws back in the loudspeaker. Now that
you got those four screws back in the loudspeaker, grab your Taptic Engine, set it down in there.
Now excuse my fingers, but we're going to go ahead and reconnect this connector right there.
Make sure it's pushed down in where it goes. Then we'll grab this plastic part and set it down in
there. Then go ahead and put your screws back in this part and this part. So next grab your
motherboard, set it down in here. Make sure to slip in under this thing right here. Now you
want to watch this connector right here so he doesn't get in the way. Watch this connector up
here and watch these antenna wires right here. Gently get them out of the way. Now since it's
setting down in there nice, let's go ahead and put our four flat-headed screws back in there.
So just to double check, one goes down here, one goes here, one goes here, and one in this corner.
So that's where the four flat-headed screws go. Also when you're doing this corner flat screw,
make sure to put that connector that's there underneath the screw, not above the screw. It
has to go on first and then the screw goes through it. Now one thing that I found, if you use your
phillips screwdriver to get them started, if it has a good magnet on it, you can gently get them
started a lot more flat and square with the phillips screwdriver. And then once they're
started then you can tighten them up with the flat-headed screwdriver. That's just a tip that
I've discovered. Next you want to get your antenna wires. You want to get the long one in first and
the short one in front of it tucked into that little holder right there. Then go ahead and
refasten these two. There's no confusing where they go because one's longer than the other. So
go ahead and refasten them. Try to keep them as square as possible and just clip them on there.
Next let's reconnect this connector up here. Now we're going to reconnect this connector right here.
So now that that's clipped in, make sure to leave this one disconnected for now because that's the
battery. Go ahead and put this phillips screw in that goes right there beside that connector.
Now that you got that phillips screw, let's go ahead and reconnect this connector again. It's
kind of awkward to show with my fingers in the way, but you can feel it click in. Next let's set
this shield down on here and put those two screws back in. Next we'll put this thing in the corner
here and put the two screws in there. Next we'll grab this part, set it down in there, and put
those three screws and that one up top in there. Next we'll grab the rear camera, set it down in
there, reconnect that connector, make sure it's good. Then we'll grab our shield, set it on top
of there, and put your two screws back in. Next you can put your SIM card tray and any SIM cards
back in. Now next before you install the LCD screen, this is a time where if you do want to
reapply the waterproof adhesive, then you go ahead and put it around all the way around on the edge
here. So go ahead and do that next. If you're going on without that, then you can skip this step. Next
to reconnect the LCD screen, first we're going to connect this connector right in here, and this can
be kind of a pain. Sometimes it's easier to like turn the screen a little bit, try to line this
connector up the best you can. I would be careful what you stick in here as far as anything metal,
but sometimes if you get it close you can press down with something like this or something to get
it started, and then you can finish it with your finger. It's a little tricky with this camera
right here, so you got to watch that. So now that you got that connected, now we want to reconnect
these two connectors here. So do the shortest one first, and go ahead and connect this connector.
Now we can go ahead and reconnect the battery. So then you can grab this shield and set it down
on top of here. Now this little foam piece that's right here where the camera will make this sit up
for a little bit, but it'll compress once you put your screws in. So go ahead and put those two
screws in. Now that you got your two screws in up here, grab your shield here, set it down on top
of this right here, and go ahead and put those four screws back in. Now that you got both shields all
done and all the screws back in, let's go ahead and gently lay this down. Now as you got it here,
clips right here, we want to get those started in there first. Then you can go ahead and just
gently press that down all the way around. Then go ahead and put your two screws back in the bottom
right there. And hopefully this video helps you. Thanks for watching!
