How To Install Trex Composite Decking

QYR
32 followers
12 Video ViewsยทOct 25, 2022
Welcome back to the channel guys, in today's video I'm going to show you how to install
trex decking and if you're new to this channel my name is Josh, this channel is all about
building your own house saving a ton of money so be sure to subscribe if you're into that
and smash that like button if you find value in this video.
So the first thing we got to do is chalk a line because we want that first piece of trex
nice and straight so let's get to it.
Trex is five and a half inches wide so I want a half inch overhang so what I did, I went
to the far end of the deck here, pulled over five inches, put a nail, hooked my chalk line
to it, came over here, marked five inches and now I'm going to pull the chalk line really
tight and snap a line so that way it gives me a half inch overhang.
Alright so this is the first piece that we're going to be starting with, this is the square
edge trex, you don't want to use the grooved edge for the first piece because you need
to be able to have a flat surface here instead of that groove showing, that doesn't look
good.
So first thing we do, we had to cut each end, not this end because it's butt in the house,
didn't really matter, but the far end of this board.
Make sure you cut it square first because these boards do not come square, just so you
know.
Okay, so now I'm just going to line it up on my chalk line I made and I got about a
quarter inch gap here from the house because you don't want to butt it tight and that looks
good and now I just take an eighth inch bit, stay about three quarters inch from the edge
here or so and we're going to pre-drill a hole here and then over here.
All right, that looks good and now I got these deck screws that are made for composite decking
and if you need to know how to build a deck like this, go ahead and check out the link
above, it'll show you how to build this exact deck.
All right, so now I'm going to go ahead and tack a screw here and these screws, like I
said, are meant for composite and you just want to countersink it flush with the top
of the decking board.
All right, now that we got our first one started, all you got to do is line the board up with
the chalk line that we made and then put two screws in each joist.
Let's get to it.
All right, so I already installed the next board that goes up against the one we started
and I wanted to show you that you need to leave a really fine gap here, about an eighth
inch.
Now, it's got a random piece of metal here and so before I butted this one up to this,
I went ahead and put this in between, put it tight and then put two screws here.
So now, our starter board is done and now we got to put brackets to get ready for the
grooved boards.
So the easiest way I found to install these first brackets that go on, just go ahead and
get a shim that's the same thickness of the gap that you're going to need.
Go ahead and place the bracket right up against it, take a little eighth inch drill bit and
just so you can start the screw, okay, and then place your screw in that hole and then
drive it tight.
All right, now it's spaced out a perfect quarter inch and all these are ready to go.
Now our next board, you just slide right up into it and that groove catches it and then
we can continue using our regular bits or screws and it's going to be the ones we use
after this.
So you cannot use these to begin with because there's no groove in this starter piece for
this to go into.
You got to use these brackets.
Okay, so as you can see, I got the brackets on every joist going across here and now it's
time to install this one and now this one, you want to make sure you cut so that way
you have a square edge because these do not come square out of the factory and you simply
just slide it into these brackets and then make sure you push the board so it's square
against the other board, okay, and then come back over to this one and make sure you got
just a thin gap here between the two joints.
So something about like that, that looks really good and now all you got to do is push your
board tight into this bracket and then take this fastener, slide it into the groove and
tighten it down.
All right, so it should go a little something like this.
We have it slid into those brackets.
I'm going to push with my leg here and take this fastener, slide it into the groove, make
sure you're really tight.
That looks good.
Here we go and now come to your next one and do the same thing, going clear across the
whole board.
All right, so after you get those brackets on, I'm going to show you the system I found
that works best for me.
I went ahead and cut these two boards and I have them spaced quarter inch from the house
on each side and I'm right here at the joint and the joint looks like what we want.
So now what I'm going to do is go ahead and place this board into the slots and I'm going
to show you the best way to set the hidden fastener.
All right, so after you have this board slid into the existing brackets that you have holding,
just take a hammer and this is where you got to be real careful.
Don't smack the board really hard.
Just get a slight peck, just barely tapping it, it should slide right into those fasteners.
Again, don't hit it hard, very easy because you will damage that board's edge.
All right, so I got that tacked into place.
So once you have this tapped in tight to the other bracket, go ahead and get a hidden fastener
and place it into the slot here and go ahead and snug it down.
Do not tighten these brackets down when you go to hold it.
So you want to snug it down.
Go ahead and do about two or three in a section.
Again after a trial and error I found out for this to be the best way to go about this,
especially when you're working by yourself.
Again, don't tighten these down yet.
Just snug them up.
All right, and after you got a section of them done, in this case it's three, now you
tighten the ones back behind here snug.
Well more than snug, tight, as if it was going to be there forever.
All right, so now this section here is in place and it's going to stay there forever.
All right, just to recap, these are the three I just put in and I went ahead and put these
in.
You can still almost wiggle these a little bit because you don't want those too tight
because the next word slides into here, it's going to be hard to line up right.
And you just want to make sure as you go, tighten those up back here all the way.
So the system is again, go ahead and put it tight against these, hold your bracket up,
snug it up, snug it up, snug it up, and then come back through, tighten, tighten, tighten.
And then just do that throughout the whole length of the board.
All right, now we got that 16-foot board fastened, now we need to go ahead and butt this one
up correctly.
Okay, so to space this correctly, take your spacer, slide it into place, and go ahead
and slide your board into the existing hidden fasteners.
That looks good.
And now, make sure you're spaced correctly still, that looks pretty good.
Double check.
Yep.
All right.
Now, take your hidden fastener here and make sure we're back all the way, looks good, and
just snug it up.
All right, looks good, not super tight, that's what you want for these, and then tighten
one back behind it all the way.
All right, and then so on and so forth until you got this whole 8-foot board on, all the
way to the wall.
All right, and once we get to the end, we need to put two screws here, so what I do
is pre-drill with an 1-1โ8-inch drill bit first, okay, and then you take your composite
decking screws, so then you put a spacer here to make sure you're spaced correctly.
Go ahead and start your screw and just countersink it into the Trex a little bit, just so it's
flush on top, and then remove your spacer.
All right, and now that's how you finish the ends of the Trex.
So a little tip that's gonna help you be quicker, get two drivers, one for your decking screws
and then the other for your hidden fastener, that way you don't have to switch the ends
in and out all the time, and then have a third tool, which is gonna be your 1โ8-inch drill
bit ready to go at all times because you use those three items frequently, and if you're
wondering what these hidden fasteners look like, that's what they look like up close.
That end slides into the grooved part of the Trex, and then this end here acts as a spacer,
so it's a pretty nice little fastener.
They're expensive, to be honest with you, but it gives you a nice-looking job when you're
done.
So those are my tips.
Okay, I'm gonna get back to putting down decking boards.
So what you wanna do to make sure your Trex is running true, go ahead and measure from
the house up to it, and be sure that it's still running straight.
So right there, we got 100 inches, and then over here, go ahead and get in the middle
of the deck somewhere and pull another measurement, and that way, when you get up to the house,
you have a straight line going, so it's not crooked.
Just make sure when you started it, it should've been straight to begin with, but just in case
you start running off a little bit, it's always smart to double-check.
So just a little tip.
All right, I ran out of Trex, but I wanna show you what you do when you get to the end
here.
I gotta order some more Trex.
It'll be here in like a week, but what you do is, let's say you need half of a piece
to finish in a strip here at the end of it, what you do is leave it about a quarter-inch
shy and then put a screw wherever your joist is, but a quarter-inch from the edge.
So that way, when you put your siding on, your J-channel's about an inch thick, it'll
cover up that screw in the back, and that's how you're gonna finish up your decking.
So if you're wondering what saw I was using to cut the Trex, I'm using this double-bevel
sliding DeWalt saw, but any brand saw clearly is fine.
But make sure you have a finer-tooth blade on it for trim.
This is a 60-count blade.
But if you come over here, make sure you get a stand that has these arms on it because
this stuff's really flimsy, the Trex that is, and these arms will definitely be used
to support it.
You could always set up a workbench or a saw horse to handle the end of the Trex, but that's
what I'm using is just this saw.
But if you look at this saw, check this out.
Has this shadow line.
Instead of using a laser, it uses a shadow.
I love it.
Here is what the ends ended up looking like, and there is nothing wrong with that.
We have a nice expansion gap.
It's hard to see in the video, but there's a good quarter-inch there for expansion.
And if you come over here, if you look at our joints, these joints turned out really
nice and uniform.
Can't complain there.
Now, I noticed this stuff gets pretty warm when the sun hits it.
So all in all, can't complain about it.
Like I said, I've got to wait a week to get everything to finish up this section that's
left, but I got pretty far on it.
Cannot complain.
All right, guys, I've got to go get my girl off the bus, so I've got to run.
But I just want to say thanks a lot for watching.
Be sure to subscribe and smash that like button.
And again, my name's Josh, and I appreciate you watching, and I'll see you in the next
video.
Peace.
