How To Install Soffit And Fascia

QYR
32 followers
237 Video Views·Oct 25, 2022
Welcome back to the channel guys.
In today's video, I'm going to show you how to install a soffit and fascia like a pro.
So my goal is by the end of this video, you can do your own project with these.
If you're new to this channel, my name is Josh.
This channel is all about building your own house and saving a ton of money.
So be sure to subscribe, smash that like button, and ring the bell so you get a notification
every time I release a new video.
So if you see the house here behind me, we're going to install the soffit and fascia across
here and install the fascia across the top of that gable.
So let's get started.
So the first thing we need to do before we install the soffit is install what's called
F-channel.
F-channel is what holds the soffit to the house.
It's just more or less a track it just slides into.
So in order to get the height of this F-channel, you simply just take your framing square,
slide it against the house until it butts against your fascia board, boom.
So that tells me I'm on the same level as this fascia board.
So you just mark the top of your square and that's going to be the top of our soffit where
it hits the house.
So in order for this F-channel to work out right, you need to understand that the top
of the soffit is going to be the top of this track, not the bottom.
So when it goes across, it's going to be same level from here to here, not from the bottom
but from here.
So go ahead and make a mark and then we're going to hook our chalk line to it and go
down about 12 foot and snap a line so that way it gives us a level mark to go across
of to install our F-channel.
So I wanted to show you this up close.
Here is my chalk line going across.
That is the same plane as this sub-fascia board and right here is the F-channel I have
installed over my porch here.
So if you can see this F-channel now, it's flipped kind of upside down because this is
a finished exposed edge.
Now as you run this where there's going to be siding, you're going to want to flip it
like this.
If that makes sense, you'll understand better.
I'll show you a close-up of what this looks like on the other side of the porch here so
you better understand it.
But when you install this F-channel, you simply line the top of this to the chalk line.
So it's going to look something like that.
So you better understand the transition.
If you look closely there, you'll see from the porch beam, it transitions to the regular
part of the house and the F-channel is flipped on different sides where it's nailed.
So now that we've got our F-channel installed, we've got to get the length for our soffit
and in order to do that, all you've got to do is slide your tape measure into the F-channel,
go tight against the back of it, measure to the very end of the sub-fascia and in this
case we've got 12 inches.
So after you get your measurement from the edge to the inside of the F-channel, subtract
a quarter inch.
So we had 12 inches as our actual measurement.
We need to cut the pieces 11 and three quarter.
Let's go cut some.
So after you know the length of the soffit you need, you're going to have to cut it into
sections like this.
In order to do that, there's three very common ways I'm going to show you each way.
One's going from the most basic using the most basic tools to more complex ways using
more complex tools but it will cut it much faster.
So it goes from DIYing for a small project up to a big project for a professional.
So let's get started.
So I'm going to show you the most common way first.
It involves a framing square and a pair of 10 snips and all you've got to do is just
cut it like a regular board.
So first thing you would do is just go ahead and make a measurement, say 11 and three quarter
in this case and you would go ahead and just take your framing square just like you were
going to cut a board, lay it against a straight edge and then slide it up to your mark and
that way it's going to give you a nice square line and then you simply just take your 10
snips and cut along that line like so and this stuff cuts relatively easy and the colder
it is, the more brittle it is so you need to be very careful not to crack it.
So just trace that or cut along that line and then boom, you've got an 11 and three
quarter inch piece.
This is not the method I use on my jobs, I typically use another method that's much faster
so let me show you that one.
The second method that I like to use involves a soffit jig and if you need to know how to
make one of these, I'll put a link up here to a video I made on how to make this exact
jig.
So this involves a circular saw, in this case a battery circular saw with the blade turned
backwards so that way it doesn't damage the soffit as it cuts because it's too aggressive
if you have it turned around the regular way and it involves wearing ear protection because
it's super loud.
So if you need to use a circular saw, I recommend using a jig like this and this soffit comes
in 12 foot sheets so you can get 24 pieces by the time you double up the soffit because
there's two sheets laying here so each cut gets you two foot of soffit.
So it's very fast and portable so this is one I like to use so I'm going to show you
how to do it.
All you've got to do is go ahead and you can either measure onto the soffit of the
length you need so you can just measure over let's say 11 and three quarter and make a
mark or you can have a reference line on your soffit jig like I do for every couple inches
so that way you can just use it as a reference but either way works well.
So that looks pretty good right there and then what's very nice is there's no skill
in the cutting this you simply just lay it into the track and just run your blade right
down it and then voila you have two pieces of soffit and you can just simply if you have
a mark on your jig line it up to that mark and run it down it.
All right let's move on to the third way which is probably the most common way other than
using a soffit jig to cut it fast.
Let's do it.
So the third and final way that I've found you can cut soffit fast is using a miter box
like this that slides so you can get these long cuts so cutting 12 inch soffit is easy
with something like this.
So the only reason why I don't like to use this method is because it's hard to kind of
hold the soffit mark it and cut it that's why I found the jig to be much faster but
if you use this method be sure to take your blade off and turn it around backwards preferably
use a trim blade so it's already finer tooth then once you turn around backwards you'll
definitely cut it without breaking the soffit if it isn't too cold.
So yeah I mean this method is fine and like I said you just need an expensive tool like
this to do it so it's probably the least common for me to use I mean if I'm in a pinch and
I don't have my soffit jig then I'll probably resort to this over the standard using the
framing square method so just something to keep in mind but that is the three most common
ways to cut soffit.
So I went ahead and pre-cut about 24 pieces of soffit and the reason why I could is because
I took a measurement every 10 foot down the overhang and my measurements were consistent
so I can pre-cut a bunch of them so I'd recommend you go through take measurements to make sure
you can do the same because fascia the sub fascia has been known to vary within a quarter
inch sometimes so double check that before you pre-cut a bunch just to save you a bunch
of wasted soffit.
All right let's go ahead and install this pile of soffit.
All right we're going to go ahead install this piece of soffit it's very easy to do
you have a nailing flange on this side and then an interlocking channel on this side
so you just take this side lock it into the existing soffit slide it into the F channel
make sure it's nice and snug and make sure it all looks good as far as an expansion gap
that all looks really good go ahead and take a aluminum roofing nail I use an inch and
a quarter galvanized go ahead and nail it into the nailing flange on the sub fascia
and this is something you do nail relatively tight make sure we look nice and square it
looks good and the reason why you nail this stuff tighter than you do sodding is because
sodding you need to leave enough room for it to kind of be movable now this is going
to be solid so by the time you put your fascia up here it's not going anywhere anyways but
so wind don't blow it out for sure always nail it snug and now the next piece is going
to require a soffit vent because I got a bathroom on the other side of this wall so in order
to vent the bathroom I need to come out the soffit so I'm going to show you how to install
that next.
All right so this contraption is called a soffit vent and the idea here is this is under
the soffit and this goes above the soffit and this just sandwiches between the soffit
so what you got to do take a piece of soffit and cut the center out like this and you just
slide the piece together and what you need to do before you slide this together before
you install it you need to put a block up above to nail this to before you install your
soffit but I'm going to go ahead and snap this together so you'll see what it looks
like on the ground so you just slide it in here into your pre-cut piece it's very you
want to cut this relatively tight because you want to make sure bugs can't slide in
between the cracks here so that's pretty important so again slide that in tight as you can see
a nice solid fit looks good and then if you're putting this piece on in this particular model
you want this solid edge on the pointing out so you don't see inside the venting so we
know we're going to snap in like this so we need to put our solid piece pointing out like
that so you simply after you have this installed like that above you just snap this together
like so just going to snap together and it's pretty easy after it's nailed because you'll
have a solid piece to push against so by the time it's said and done you're going to have
something that looks like that hanging so it's pretty pretty sweet contraption sometimes like
said at these bathrooms you can't vent out the side of the house because there's no way to vent
because the way the walls land so just FYI let's go ahead and continue that soffit from below that's
what your soft events going to look like it gives it a nice sleek appearance each piece of soffit
covers a foot so after you get going with this and get your own little system down it moves pretty
quick and if you look at the trees in the background there was a good bit of wind going
on while I was making this video so you will hear some wind noise here and there so just as a little
heads up and after I get this soffit up to the end of that F channel it's time to install the
next piece of F channel and I usually just start in the middle and go ahead and nail it at every
stud I try to hit every stud while I nail this sometimes I miss and I have to put a nail in
the nail but all in all I do hit the studs it does make a much more solid piece of F channel
when you do that and here I am just continuing that run on the new piece of F channel and you
want to make sure as you go across like I said before just put those nails in snug if you want
this process to be a little more efficient you can install the soffit and fascia as you install
the siding if you're using a scaffolding and reason why I say that you see how many times
I got to move the ladder and not only that it's so much easier to work off a scaffolding instead
of a ladder I want to show you what you do when you get to the end here so when you get to the
end of this bird box right here you just got to nail the ends with aluminum fascia nails because
there's no way to have a nailing flange here because when you in the run you're gonna cut
that off to end it so you're gonna have something it looks about like that so the product I'm going
to be installing for the fascia is six inch ribbed aluminum fascia and you got to fasten this using
aluminum nails so I got small white trim nails that are aluminum that's going to blend in with
this fascia and how you install this fascia on this overhang is different compared to how you
install it on a gable end because this gets guttering put on it so you can face nail this
but you can't face nail the gable end and I'll show you how to do that in just a bit so the first
thing you got to do is slide this up under your drip edge that's on the roof so you got to overlap
the other piece about a inch or so and then it slides up under the drip edge and sometimes you
got to work it back and forth to get it under the drip edge and this is much easier to do it to
people but I'm one of those that works alone a lot so I choose to save a couple dollars all right
so after you have this thing pushed up under the drip edge you want to make sure your overlap is
no more than an inch and no less than an inch all right so after you get your overlap correct and
it's a little uneven there so push it up all the way and now just put a trim nail here in the center
and push it up tight against the soffit we're just going to face nail right in the center so I always
put two nails every about three foot or so there's no exact science to the nailing but I wouldn't put
it any farther apart than every three foot so now just nail it every three foot then at the joint
we put two in the joint as well so that way it kind of ties all that fascia in together so just
do that till we get to the end where the bird box is and that's where I'm going to show you a certain
way you got to cut around that bird box stay tuned again I can't stress this enough you only face
nail the fascia where you're going to be having guttering screwed to the fascia just keep that
in mind okay so once you get to the end of your fascia do not nail it yet because as you know
already that gets overlapped so you keep that nail free to your next piece overlaps like we did over
there then we nail it all right so in order to finish this run I need a 92 and 3 quarter inch
piece to come from the end here and to overlap an inch on the other piece but I'm going to add
another inch and I'm going to overlap this bird box I'm going to show you why after I wrapped this
whole thing but I'm going to show you how to cut this end piece so we'll cut that then I'll show
you how to wrap the bird box so let's get into the garage and get it cut so here's our piece of fascia
so we know we need a 92 and 3 quarter inch piece exposed on the overhang so we measure 92 and 3
quarter and we make a mark on the piece that overlaps the soffit because we're just going to
make a cut there so go ahead and mark a straight line there I use a speed square it seems to be
the quickest hence the name speed square and then we just go over about an inch then that'd be
perfect so it's roughly an inch and we're going to make a square line going across the face all
right so we're going to cut this come over and cut that and then I'll show you how to bend this to
wrap around that bird box so what I like to do before I cut this is just flip it over and then
score the crease between this line and this line because this is going to allow you to break it
easier instead of trying to cut it with your snips so that's scored very very deeply and then
go ahead and cut this side all right and then sneak on the other side here and cut that side
all right now since we have that side scored that we did it should snap pretty easy so there we go
so lay this scrap to the side and this is our piece we're going to need so flip it over now
we need a straight line from this edge from here scored so we just go ahead and put our speed
square there score it not real deep just kind of lightly and now you just take a block that square
lay it up to where you scored so somewhere around there and I'm going to go ahead and just rescore
it to make sure we're on the right line okay again not real deep this is just so you can bend it
easier and now we just got to bend this end up there we go and this acts as a nice guide to keep
it square and then I'll go ahead and fold it in a little more that needs to be and then fold it out
just a little bit so that way it gives us a nice sharp appearance okay so something like that so
from this side you have a nice square piece that's going to wrap that bird box it's going to look
really sharp when it's done all right so that's the piece finishing up the run and as you can see
here the reason why I bent this metal is because when you put this L piece on the wrap this bird
box this is going to be an exposed edge if you cut it flush but if you wrap it any water hits
that corner and will run down this aluminum instead of touching this wood behind so now we got to wrap
this like I said so all we got to do is get a measurement from here to here and then from here
to back here then we know exactly what we got to bend and then you measure the distance from here
to here to know how wide this has to be to wrap it so we're going to use the remaining piece of
that metal to make this bird box wrap and the first thing we got to do is measure over for our
face so let's go over 11 and 7 8 and then we're going to take our speed square mark a square line
okay and now we're going to go ahead and snip that okay all right and now what we're going to
do is cut a little triangle out of it now I'll show you this up close here in just a second
and that's way with that triangle out of there it'll bend easier if you're wondering why you
gotta do that so that's what it looks like a nice triangle here's a straight cut then a little angle
and then we make our next measurement which is 11 and 3 quarter heavy and I say heavy I just mean
sixteenth more than 11 and 3 quarter that is construction talk all right and now let's go
ahead and square that right and now this one we're going to cut off all the way so we're going to go
ahead and cut that straight line now we're going to put a straight line using our speed square here
and snip that all the way off a good pair of 10 snips are hard to beat for this I wouldn't recommend
buying just any 10 snips I'd buy a good pair all right and now we're going to come back to where
our straight line is here and use our straight edge board we're just going to line up with our
cut mark let's see try and get this to where it sits the best it looks pretty good all right like
I said always score it a little bit before I bend it just gives it a nice line to follow all right
so now just go ahead hold the board tight and bend that metal over okay so now we'll get the
board out of the way and finish bending that all the way over and always like to take my hands and
just go ahead and bend it more than it needs to be okay and then pull it back just a little bit
so that way it gives us a nice square edge and as you can see it's a nice sharp crease in there
which that's what we want and now let's go install this piece of metal all right so in order to
install this all I gotta do is place it over the bird box like so push it up snug on each end make
sure it all looks good make sure you're not overhanging too much over here and the corner
looks good everything looks good so now just hold it up into place and the only place you can nail
this for the moment is right up here we're gonna tack a nail in here to hold it all right and now
don't nail this side yet and we can put another tack up in this corner okay put these nails up
high because the soffits going to cover those nails up and you don't put any nails in the face
here and then like I said don't nail this yet because your piece of fascia that comes over this
gable is going to overlap this you don't want nails in the way so we're gonna cut this piece
of metal next I'm going to show you how to cut it and how it nails into this piece so what we
got to do is get a measurement of our overhang here so it looks like we need at least we can
do 14 inches so we're gonna come 14 inches past this with the metal cut it off straight and then
we can fine-tune it after it's overhanging so this doesn't have to be the perfect length because like
said we can cut it off after we install it but just make sure it's long enough to go across this
on a diagonal so let's go cut that all right so grab your piece of fascia lay it face down make
sure you're using the right side depending on what side of the gable you're on let's come back here
measure 14 inches so right here's 14 inches and this is just a rough measurement at this point
because we're gonna fine cut it after it's up I'll show you how to do that in just a moment so go
ahead and square that up okay and now before you cut and break that what we're going to do is score
this several times I want to make sure you have a nice deep score here because it'll make it easier
when you go to bending and cutting or breaking this edge off I should say all right so three or
four good scores should be fine and now take your ten snips cut down the line and now you don't cut
the face obviously because we need this part to overhang so now the best thing to do is bend this
over okay then pull back on it and it'll snap that piece off and now this is going to give us
something to overhang that bird box so let's go get installed all right so in order to install
this you must first slot it up into your drip edge just like you did the other fascia all right
so now as we slide it all the way down make sure we're tight against that bird box that looks
pretty good and now we go ahead and push it up tight we're going to take a trim nail and instead
of nailing the face of it this time we're going to nail it up under into the groove of the soffit
so we'll go ahead and get a nail started here and I'll show you up close after I have this installed
what it looks like and be real easy you don't over nail it because it's easy to over nail that
all right and then every three feet or so put a nail up under it into it make sure you're tight
against the subfacial when you do this because if it's bowed out and you nail it it's gonna be
difficult to get it back all the way if you can all right it's a little breezy today too which
that makes a little more difficult as well so now I'm going to go ahead and show you how to cut
this end off it's very easy but I'm going to show you so you must not forget that this part right
here wasn't nailed yet so you got to make sure it's tight and then hold your piece you just put
on that's overlapping it and just pop a nail right in the middle right here towards the lower end of
this so that's the only spot you should have to face nail on this whole gable for the fascia so
as you can see this doesn't look right right so now that this is sitting where it needs to be all
you got to do take your pencil and scrub from behind where it needs cut off on the front and
back okay and now all you got to do is take your ladder on the other side cut those lines and then
it'll cut right off that's why you don't nail this end yet because you can flex it out to cut
it easier depending on what handing you are it could be easier one hand versus the other right
and that looks pretty good so now as you can see you just got to go back on the other side and put
a couple nails to hold that into place all right I usually come back about a half inch and nail
this edge that way it just seals that end up really nicely so that's how you wrap your bird
box in metal I hope you found that easy so now I'm going to grab the camera and I'm going to
show you underneath where I nailed it so you understand what I meant by nailing into the
soffit groove okay so if you look here there's this soffit is see the nail is into the fascia
and into that groove you don't want to nail here because it'll push this soffit up when you put a
nail in it so you want to make sure you're in that groove and that's what it looks like here
another thing I wanted to show you you can nail right here too because your J channel we're
actually your vinyl corners gonna come up and cover this up so if you stay within about a half
inch three-quarters inch you should be able to cover that up with corners and if you look over
here that's what that looks like and it's up to you if you want to put nails in this drip edge I
do sometimes if it's sticking out a lot but you know some people recommend not doing it in case
they gotta replace your roof and pull that drip edge off and it's nailed to your fascia so that's
kind of your choice but that's what that looks like up close and let me show you what the bottom
looking like you'll probably be happy with it I was happy with it that's what it looks like I was
a long run that was about a 70 foot run of soffit and fascia so turned out all right I cannot complain
about that all right guys I hope you found this video helpful if you have any questions about this
project I just did as far as the fascia soffit anything of that nature go ahead and ask them
in the comments below and I'll get to you as soon as possible and again I want to say thanks a lot
for watching be sure to subscribe smash that like button ring the bell so you get notifications
every time I release a new video and thanks again guys and I'll see you in the next video peace
