Beast Mode – NVIDIA RTX 4090 Review

Abrine ß X
49 followers
9 Video Views·Oct 21, 2022
So let's finally talk about the performance
of this thing right here, the RTX 4090.
And yeah, it is truly insane.
Like the kind of frames that this thing is pushing out
at like 4K max graphics.
Yeah, you won't believe the numbers until you see them.
So we've already gone over the exterior design
and how this is different and talk about the specs
and everything like that.
Today we are solely focusing on the performance
and the benchmarks.
Now the first benchmark that I ran for the 4090
was this right here.
Forza Horizon 5 running 4K completely maxed out.
And I mean, I had to double check
that I wasn't running lower settings
or mess something up here, but no, this is real.
This is the new 4090 literally doubling the performance
of the 3090.
This is also without any ray tracing, DLSS
or anything like that, just pure rendering output
and it's pretty insane.
Then I switched over to God of War,
also 4K here at the highest possible settings.
And again, no ray tracing or DLSS just yet.
We'll get to that in just a minute.
But I mean, just look at the brute output of this GPU.
It's so much higher than I expected
without those RTX effects enabled.
Here we're looking at about an 80% increase
over the RTX 3090 and it's not far off
triple the performance of a 2080 Ti,
which is still a strong GPU by today's standards.
Games that might've been previously demanding at 4K
even on last gen flagship GPUs,
they're just not even remotely challenging for the 4090.
Dying Light 2, for example, the 2080 Ti does struggle a bit.
You'd probably need to lower some settings
and the 3090 just delivers a 60 FPS plus experience.
The new RTX 4090 though, I mean,
it's kind of almost laughable at how fast it actually is.
Now, if that wasn't ridiculous enough,
here's the new Overwatch 2 running at 4K
with medium settings.
And there are multiple times here where the 4090
hits the in-game frame rate limit of 600 FPS.
Again, that's at 4K.
Now, of course, those kinds of frame rates,
they're possible at lower resolutions
with weaker GPUs and lower settings.
But again, just to flex the raw rendering power of the 4090,
it's pretty nuts.
Nvidia are always kind of secretive
about the gains of rasterization only performance
when they announce these GPUs.
And that causes people to kind of speculate
that the performance gains aren't that much.
But as you can see, they are still pretty substantial
without even factoring in ray tracing or DLSS.
So in the end,
when we're looking at pure rasterization output,
we're averaging close to double the performance
of the RTX 3090 at 4K.
That means that most of the time
you're actually hitting over 150 FPS
with maxed out settings.
And in some cases,
you're actually going beyond
what the fastest 4K monitors are possible of displaying.
So yeah, I really meant it
when I said this thing is insane.
Like you just won't actually believe the benchmarks
until you actually see them.
And they're just mind-boggling to see 4K
running at those kinds of frame rates,
especially with maxed out settings.
Talking about settings,
let's now talk about ray tracing and DLSS.
And the thing about these features
is they're no longer really considered
niche or special features.
For one, the amount of games that actually support RTX
and ray tracing and stuff like that
is a huge list of games.
Like most modern games coming out
will have these features implemented.
And secondly, I've also seen some games
have these settings enabled by default.
Like if you go and select high or ultra high,
you will actually have to intervene
and turn off ray tracing
because that's what the developer has put in
as an ultra high setting.
So as you'd expect with more RT cores
and Tensor cores on the 4090,
as well as just being more powerful in general,
switching on RTX leaves the 4090
with a much more capable experience.
Here we're looking at control running at 4K,
everything maxed out, including ray tracing,
and also with DLSS set to the balanced mode.
The RTX 4090 has a new trick though,
and that's a DLSS 3 feature called frame generation.
In a nutshell, what this is doing
is comparing two frames that have already been rendered,
and it uses AI to make a completely new one in between them.
Essentially, it's artificially increasing your frame rate
by inserting AI fake generated frames.
And as you can see, the frame rate increases by doing this,
even over the increase by using DLSS in performance mode
is really, really strong.
In the end, it's about a 50% bump here in Cyberpunk,
which is comfortably running at around 140 FPS.
Now, when you take a look at how much frame rate cheating
is kind of happening here, it's pretty insane.
With max settings and ray tracing enabled
over on the left there,
you can get a grasp for how demanding graphically
these settings actually are
without any AI generated frames or AI upscaling techniques.
With DLSS and the new frame generation though,
you're effectively getting over triple the frame rate.
One of the coolest parts about this though
is that you can kind of cheat your way past CPU bottlenecks.
Microsoft Flight Simulator, for example,
has a massive CPU bottleneck,
but here it is somehow running at over 200 frames per second.
Now look, it's pure overkill here with the 4090,
like no one needs to be playing this game at 4K
at these frame rates.
But when this feature trickles down to the lower end cards
that aren't as capable at 4K or 1440p,
that's a bit of a game changer for certain games.
For those wondering as well,
it is also possible to run the new frame generation feature
without any form of DLSS upscaling.
And the frame rate boost there by running it alone
is still pretty strong.
So frame generation is pretty interesting
and we'll get to my personal thoughts on it
in just a second.
I did quite a bit of playing with it in Cyberpunk,
but aside from it not giving you perfect frames all the time,
which to be honest, you don't really notice
if you're like playing through the game quite fast,
it's really only something that you notice
if you're like recording gameplay
and then you go back to kind of pixel peep the frames.
Otherwise, if you're just playing through,
you really don't notice those AI generated frames
and that kind of simulation.
The other thing though, which you do definitely notice
with this feature is the increase in input lag.
In Flight Simulator, for example,
there is a massive 46% bump to frame rate as we saw,
but there's also a pretty big jump in latency.
In this case, it's almost double
compared to just enabling DLSS.
Cyberpunk wasn't as bad,
but still a pretty considerable increase,
about plus 12 milliseconds here over just using DLSS.
So although DLSS upscaling provides
both a frame rate increase and latency decrease,
frame generation also gives you a frame rate buff,
but at the same time, increasing latency.
So having this in mind,
I've actually played Cyberpunk for a bit with this feature.
I'd switch between frame generation on versus off,
trying to get an honest feel
for the actual experience differences
with and without the setting,
as opposed to kind of just looking at the numbers.
And yeah, the increase in input lag, you can feel it.
I think it's most noticeable on mouse and keyboard
if you're like intentionally trying to notice it
and you're switching the setting on and off.
If you're playing on controller though,
it's definitely less noticeable.
And I think the style of games
that frame generation is more suited towards,
that kind of makes sense.
The increased latency, it is still there on controller,
but not as bad.
What is way more noticeable in my opinion though,
which is a pretty easy trade-off for me,
is that massive boost in frame rate,
especially in Cyberpunk where without frame generation,
you're kind of sitting below 100 FPS.
And you do notice that smoothness quite a lot.
You know, your inputs will feel slightly heavier
with frame generation on because of the extra input lag,
but the gameplay overall,
I would say at least is improved with this feature.
Now, of course, if you already have a game
that can run at pretty high frame rates,
this is a setting that you should probably
just not worry about,
especially if the gameplay suffers
from that increased latency.
F1.22, for example, is another game
that will support DLSS 3 and frame generation.
Again, pretty decent bump to frame rate here,
but for a precise game like this,
you're just better off lowering
some actual quality settings
if you feel like you need that extra frame rate.
Now, something else that's new with the 40 series GPUs
is the new NVENC encoder setup.
So the 4090 is actually running two
of the new NVENC encoders that can encode in AV1.
As someone who does a bit of streaming on the side,
I was personally pretty interested
to see how much of a buff this would be
compared to the NVENC on the 3090.
In terms of quality,
there's a pretty noticeable difference
between H.264 and the new AV1.
I'll have to pause frames here
so that YouTube compression also doesn't get too involved,
but you can see how much less blocky AV1 looks
compared to H.264.
Both of them here are running 1080p,
8,000 kilobits per second with preset one in OBS,
which basically is the fastest and lowest quality preset.
And this shot here,
you can see how much cleaner AV1 looks.
And it's actually way more noticeable
when you're running lower bit rates.
So preset three here,
which is the fast kind of low to medium quality preset.
And I mean, it's just night and day
between H.264 and AV1.
Even at just 4,000 kilobits per second,
somehow AV1 just doesn't have
that same kind of blocking compression,
like at all.
It also seems extremely good
at recognizing visual elements
like shapes, outlines, texts, icons,
and stuff like that,
rather than just compressing it all
into the same kind of muddy mess.
Now, if you feed H.264 enough bit rate
and also use the highest quality preset,
which would be P7,
it can look pretty good.
It's just that AV1 still does look a lot better.
Even with a high quality preset,
H.264 can still be prone to that blocking
and square compression that we're all familiar with.
But to be honest,
I just never saw that at all on AV1.
Now, I also did some quick performance testing here too.
In other words,
how much performance or frame rate do we lose
when we encode with either preset?
And the results aren't too conclusive.
There seems to be about the same drop-off
in frame rate between the two.
And similar, in fact,
on the previous NVENC setup with the 3090.
I'll probably test this a little bit more,
but regardless,
same performance drop-off at higher quality
seems to be a pretty fair trade to me.
AV1 encoding can also be leveraged in video editing.
So here we're looking at DaVinci Resolve Studio
and the gains there are good.
You know, they're not as extreme
as the frame rates that we saw earlier
or the frame generation DLSS3,
but overall you're looking at about 30% of time saved
when it comes to video exporting,
which for big projects is a lot of time saved.
The gains in 3D rendering though are more impressive.
Twice the rendering speed here of the 3090 in Blender
and almost four times faster than the 2080 Ti.
Those gains carry right over to V-Ray,
where we see just monster performance again,
both in the RTX benchmark and when using CUDA.
But what about that huge power increase?
I mean, 450 Watts, that's 100 Watts more than a 3090,
which is already quite insane.
Like, yeah, it's faster,
but it's kind of getting a bit ridiculous now
for a consumer GPU.
But here's where I was pleasantly surprised.
In gaming, you'd be pretty hard pressed
to get this thing pulling the entirety of its TDP,
which personally, I just expected it would
because every other Nvidia GPU does that.
But most of the time I saw it hovering
between 360 and 390 Watts.
Sometimes it did tip over that 400 Watt mark,
you know, depending on the game, if it was demanding enough.
It was only really in Furmark
that I could get it going above that.
And even still, it didn't pull the full 450 Watts.
So that's pretty unexpected.
What's also unexpected is after running 30 minutes
of Furmark, the card stayed under 70 degrees C.
Also, I'll note the memory temperatures
have been kind of fixed on the Founders Edition cards.
Previously, they were around the 90 to 100 C mark,
but now they're sitting around 80.
This is all with an ambient room temperature of 22 degrees.
And here's an idea of what the card sounds like
at full load.
Now, some quick notes on overclocking.
I did manage to get the 4090 close
to the three gigahertz mark, which is pretty insane.
Plus 220 on the core here,
but ultimately that wasn't fully stable.
So I lowered it to plus 200 and that was absolutely fine.
Somehow I also managed plus 1700 on the memory,
which makes for the fastest GDDRX speeds that I've ever seen.
And in the end, it's about a 9% bump
to gaming performance here in God of War.
Of course, not really a GPU that you'd need to overclock,
but I mean, there's a bit more room in the tank than usual,
which is always nice to see.
Now it's important to note that a lot of the kind
of new features that we've talked about today,
like the DLSS three frame generation
and the new AV1 dual NVENC encoders,
that stuff will also trickle down to the, you know,
4080s that have already been announced
and the 4070 when that will come out
and, you know, potentially the 4060
when that comes out down the road as well.
So don't be pressured to buy the 4090
if those are just the kind of features
that you're interested in,
especially when the 4090 is just so brutally overkill
for 99% of setups out there.
Like I really had to stop myself laughing
at how ridiculous some of those numbers were
at, you know, 4K maxed out graphics.
Now, in terms of pricing,
I'm going to say something that's maybe
a little bit unpopular,
but I really can't see it any other way.
And that's what the 4090 isn't really an overpriced GPU.
Now, of course, the 4080 16 gig and the 12 gig,
those are absolutely very overpriced, you know,
just looking at how that pricing compares
to the previous generation.
But the 4090, you know, compared to the $1,500 3090,
which was realistically a lot more expensive than that,
and the $1,200 2080 Ti,
compare the performance of those GPUs,
spending $100 more than the 3090,
you're actually getting an insanely more powerful product.
I mean, the kind of performance jump
from the 3090 to the 4090,
again, I'll just say it, it is absolutely insane.
And of course, goes without saying,
it's brutally overkill for 99% of the setups out there.
Like if you don't have a 4K 144 Hertz monitor
or a 1440p 360 Hertz monitor that's coming out,
yeah, don't even take a second look at this GPU.
Of course, if you want to use it for content creation,
production workloads and stuff like that,
it is definitely suitable for that stuff too.
But exclusively looking at gaming performance,
yeah, you need a very, very high-end gaming monitor
to even display the amount of frames
that this thing is pushing out.
Otherwise, I'll leave some links down below
for those interested.
As always, a huge thanks for watching
and stay tuned for a lot more content
coming up on these GPUs.
And I'll see you all in the next one.
