Hyundai Sonata Mechanical Review

The Auto Geek
46 followers
10 Video Views·Oct 18, 2022
Today we're going to take a look inside the Hyundai Sonata to see what's inside and how it works.
Now instead of reviewing the quality of the plastics inside, the infotainment system,
or the size of the cup holders, we're going to be taking a look underneath the car
and under the hood to see what it would be like if you had to own and maintain one of these.
Now we're going to start under the hood where over here on the passenger side
we have Hyundai's 1.6 liter smart stream engine.
It is a turbocharged four-cylinder situated transversely for front wheel drive.
Then over here on the driver's side underneath the battery you have an
eight-speed automatic transmission.
Now this is one of the smaller engine covers I've seen and it's not branded on the top
which means that both Hyundai and Kia can use it in their versions of the vehicle.
Now we're going to start by taking a look at the air intake system on this engine.
You can see fresh air is going to be drawn in from the front of the hood here
and be sent over down to the air box.
Now one thing I like about this air box is it's super easy to change the air filter.
It just slides right out like that and then you can slide it back in,
push these tabs in and put it back down.
Now that filtered air is then going to be sent through this mass air flow sensor
and then through this tube down to the turbocharger at the back.
You can see back here the air is then going to be sent into the turbocharger located over here.
This here is your electronic wastegate which is going to vent off any extra pressure
if you don't need it.
Now this turbocharger is going to use the exhaust flow in order to generate more flow
in the air intake stream and pressurize that.
It's going to send that pressurized air down through the charge pipe
which you can see coming down over here into the air-to-air intercooler.
Now with that air box out of the way,
it's pretty easy to see the size of this air-to-air intercooler.
It just sits by itself.
There's no fan in front of it or behind it.
You just have the big pipe that leads up to it and then the big pipe down at the bottom.
In addition, we have our excess bleed pipe that brings air back in here with a controlled valve.
Now taking a look from underneath, you can see this big charge pipe
that's going to lead up to the air intake to the throttle body.
You can also see back here this is your air-to-air intercooler
that sits on the first third on the driver's side over here.
On this side behind the radiator fan is the second third of the front
which is taken up by the radiator.
Now that pressurized air is then going to get cooled off
and be sent through this drive-by-wire throttle body
through your MAP sensor and then into this air intake manifold
which is made of a composite plastic
before being forced down into the air intake side of the engine head.
Next, taking a look at the Sonata's fuel system,
this is gasoline direct-injected only.
Here you've got the direct-injection pump
which is going to take low-pressure fuel coming from the tank and pressurize it.
Now this pump runs off of the exhaust camshaft on the back of the engine here.
It's then going to send that pressurized fuel down this tube over here.
It's then going to come down over here and go into the fuel rail
located below this intake manifold
before it's injected into the engine at very high pressure
directly into the combustion chamber.
Now of course, directly injecting gasoline down into the combustion chamber
is good for fuel efficiency as well as emissions
but the downside to that is after a while
the intake valves are going to get gummed up with carbon
because on a normal port-injected vehicle
the injectors would sit on top of the airstream here
before it goes down into the intake valves to help clean them off.
Now taking a look at the top of the engine here from the passenger side,
you can see this engine has a double overhead cam.
You get the exhaust camshaft on the back there
that drives the turbocharger
and then the intake camshaft over here
and that's all held underneath this plastic valve cover.
The engine does take 0W-20 weight oil.
Now the ignition coils on the top of this engine are located right on the top here
which is going to make for very easy spark plug changes.
And the dipstick is located right in the middle here, easy to check.
Now looking underneath the Hyundai Sonata
you can see that it has a fairly flat undercarriage here
with a panel that covers up most of the engine and transmission.
There's a metal panel as you get to the back there
and that's to help with the exhaust heat.
Now taking a look at the engine itself from underneath
we do have a stamped steel oil pan instead of say an aluminum one.
Now over here you can see the oil filter module.
It is a cartridge style filter which I don't like
because these are a little bit messier
and the fact that it's made of plastic
means that it could potentially crack and leak after a little while.
I don't really like these and I prefer the metal ones.
It actually extends back up here to the oil cooler
which is going to exchange heat from the oil with the coolant.
Now here's something also embarrassing.
This car only has a thousand kilometers
and we've also got an oil leak on the oil pan.
That means it hasn't even reached its first oil change yet
so it's not like this drain plug's not tightened.
The leak is actually coming from up here at the oil pan.
That's not looking good for Hyundai.
Over here on the side of the engine we have the timing cover
and underneath that timing cover we luckily have a timing chain
which means that you don't have to do belt replacements every so often.
Over here you have dual variable valve timing.
You can see these are your variable force actuators over here
and these are going to apply an oil pressure to the cam phases
in order to vary valve timing.
Now further down in front of that timing chain cover
we have our drive belt setup which is a little bit interesting here.
You can see down over here is where your crank pulley is.
Up at the top here is where your alternator is.
It's got this unique belt tensioner on here
which is what's going to tension the belt.
You just have to put a wrench down over here in order to get the belt off.
Now further down inside of here those bolts there are your water pump pulley.
While it is pretty tight to work inside of there
once you get the pulley off it's pretty easy to service the water pump.
Then finally down at the bottom over here is where your AC compressor is located
mostly accessed from down below.
Overall however it's pretty easy to access the alternator.
It's right over here and it's just held on by two bolts
and easy to remove and replace if required.
Here's a look at that AC compressor from underneath.
You can see most of it would be accessed from underneath
and you'd have to pull it down this way.
I'll drop a comment down below if you know what this thing does.
It's driven off of the intake camshaft and it's got one electrical connector to it
and I don't see any hoses here.
Now we're going to have a listen to the engine.
Now taking a look at some of the electronics and parts under the hood here.
This is a newer Hyundai which means that you do have your fair share of
plastics under the hood here.
A lot of the wiring components tend to have a lot of plastic on them than they used to.
At least the fuse box which is located right here is very easy to get to
right at the top here and everything is clearly labeled.
Now the engine computer is located under the hood for a short wiring harness
but I like that it's pushed back not far from the firewall
as opposed to being right in front of the engine
where it could get easily damaged in a collision.
In case you were wondering the unique line that runs up the hood
for the daytime running lights is a separate piece from the headlights here.
It starts over here and then it runs up the side and stops halfway up.
I wish they actually continue it along the belt line of the vehicle.
I think that would look pretty cool
but it's just a single piece over here with the electrical plug.
Now here we are on the driver's side just underneath the front bumper
in front of the front wheel
and you can see they've actually put in some sort of a computer over here
so if you do get into a minor fender bender or hit a sign or something
and this bumper caves in
well you're also going to be taking out a very expensive module of some sort.
Now taking a look at the exhaust setup in the Hyundai Sonata
it starts over here we've got an integrated exhaust manifold into the head
that's going to bring all four ports down to one port over here
where this turbocharger is going to mount to.
Now the turbocharger is responsible for increasing the airflow
in the intake coming in over here
and that's going to pressurize it it's also going to heat it up
that's why we have that air-to-air intercooler.
That pressurized air is going to get forced into the engine through the intake side
and that can make a smaller engine have more power.
Now the exhaust gases are then going to travel over here
you can see we've got our air fuel mixture sensor over here
and then down into the catalytic converter
a little difficult to see down at the bottom here
and then out over here to the flex pipe at the back here
and then down through the center of the vehicle to the muffler.
Now I like however that they've put the turbocharger on the back side of the vehicle
near the firewall
makes for a very easy exhaust routing to go underneath the vehicle
after the turbocharger
as opposed to having it in the front here
and then running it down underneath the engine.
Now looking at the back of the engine here just above the drive axle
you can see we do have an EGR system
this here is your EGR cooler and valve assembly
which is going to take those exhaust gases
and send them back through the intake to get reburned for pollution.
Now from underneath here you can see this is the bottom of the catalytic converter
it's then going to bring the exhaust gases down over through this way here
and then into a flex pipe
that's then going to head underneath this subframe
and then out the middle of the car.
Now from the back here looking at the exhaust
you can see from that center muffler
you've just got a single pipe that leads all the way back here
with an integrated muffler
and a single dual outlet over here.
Now of course on the N models you're going to have the exhaust split up
and come to another muffler over here to fill up this empty cavity
in the rear bumper for dual exhaust.
They even label the sport model's rear bumper with sports underneath here
so you can't mix them up.
And now we'll have a listen to the exhaust.
Now with the airbox out of the way
it's easy to see where the transmission is located
underneath the battery over here on the driver's side.
You can see this big module over here is actually the electric motor
that's going to select park, reverse, neutral, or drive
and that's because this has a shift by wire setup
it's all electronic
there's no cable that runs to your parking pump.
Now just next to the shift motor are the cooling lines
that go down to the transmission cooler and warmer assembly
located on the front over here.
You also see that there's a plastic transmission pan
located on the front of the engine
that's because the valve body sits up and down
in the front of the transmission
as opposed to underneath like traditional transmission.
Now this transmission does not come with a dipstick
but luckily we do have a fill port located over here
when you do want to change out the fluid.
Now the starter on the transmission is pretty easy to access
it's down below the intake over here
seems like you got enough room to get inside of here
there's two bolts holding it on
along with electrical connector
and you can get it out through this part over here.
Now taking a look underneath here from the transmission
we've got our drain plug located over there
and our fill check plug located over here.
Now here we've got the drive axle for the passenger side
you'll notice that it's actually a big hollow piece
and if you compare that to the drive axle for the driver's side
this is actually a solid smaller piece.
Now I notice a lot of these markings on the transmission
mention things like two-wheel drive
so I wonder if there's an all-wheel drive version of this car coming.
Come to think of it there is a lot of room behind the oil pan here
for a transfer case
and it is directly in line with the transmission tunnel
all you got to do is move that exhaust out of the way
and you could send a drive shaft going down the back.
I do wonder if there is an all-wheel drive setup that's coming down the works
given that the Camry also had an all-wheel drive.
Now here's something a little interesting
you can see this is the transmission cooler
and this is the transmission fill drain plug over here
it slightly overlaps the cooler
and the manual actually calls for you to remove the cooler
in order to access that plug
when you're doing a transmission fluid change
I find like it's an unnecessary step
they could have just trimmed it or made it a little bit better.
Now what's more embarrassing
this car is brand new and only has a thousand kilometers on it
they haven't even threaded this bolt in properly
it looks like it went in twisted
and it's not tightened compared to this one here which is fully tight.
Not sure what's up with Hyundai's quality control
they did put a QC marker dot here though.
Now looking at the steering setup here
you can see the steering shaft coming down to the steering rack
which is going to go to either side
there is no rack mounted steering motor here
the steering motor is actually mounted on the column.
Now one thing I do appreciate that Hyundai has done under here
although they're using a stamped steel subframe
it goes all the way around the vehicle to the front
you can see that that piece carries up to the front here
and then it goes over to the front over this way
and crosses over to the other side in a fully boxed frame.
Now in other Hyundai Kia products
they just stop the subframe over where the control arms are
and the front is left to just crush
with a plastic radiator cradle in case you hit something
at least here you got a bit of structure
and you got some points to jack up on
rather than going all the way underneath the back of the vehicle.
Additionally you can see they are using aluminum front bumper rebars.
Now looking at the front suspension on the Hyundai Sonata
you can see things are pretty straightforward down here
you got your sway bar over here
down inside of here we do have aluminum knuckles
now additionally we do have a ball joint here
that has a pinch bolt that pulls into the knuckle
I don't usually like that
because sometimes they get stuck and rusty in there
especially if you've got dissimilar metals
you do have an integrated ball joint
so there is no bolted on style ball joint
that you could change separately
instead you have to change the entire control arm.
Now taking a look at the Sonata's front suspension
you can see we've got a McPherson strut
which is nice and simple here
now that's going to bolt over here
to an aluminum steering knuckle
and then we've got our inner and outer tire rods over here
now just in front of that strut
we have a long stabilizer link
that goes down to the sway bar
in front of the wheel center here.
Now taking a look at the control arm
you can see that it's going to bolt up to the subframe
right here and here
pretty easy bolts to get to
nothing in the way
as well as the back control arm bolt over here
so replacing the control arm
isn't going to be too difficult
it is made of aluminum
which is good to see that
they've actually spent some money
on developing these parts.
The only thing I really don't like
is that this ball joint is not really replaceable
you have to replace this entire control arm
if your ball joint tends to wear out
and for those who want to swap sway bars
with maybe the N-Line model
the two bolts for the sway bar
is located right here
I'm surprised it's actually pretty easy to access
overall though I think a McPherson strut
front suspension suits the class of this vehicle
being just an economy mid-sized car
and it's going to be pretty easy
to replace parts down the road
when they do wear out.
Now you've got clearly a very nose-heavy car here
you can see the back wheel
is just as much off the ground as the front wheel
but I've got the jack underneath the mirror
right up to the front here
so that's where your center of gravity is
pretty far forward.
Now taking a look at the rear suspension
on the Hyundai Sonata
you can see we have a multi-link suspension back here
like many other mid-sized sedans and SUVs.
Now over here at the bottom
you can see we have a stamp steel
bed pan control arm that holds the coil spring
you can also see the tiny little stabilizer link back here
and the shock absorber
that also mounts to this control arm.
Now from the top here
you can see the stamp steel
again upper control arm
that's mounted to this aluminum knuckle.
Now replacing the shock absorber
should be pretty straightforward
you just got two bolts at the top here
and then of course one bolt down
at the lower control arm.
Now at the front here
we have a control blade style trailing arm
that's going to connect up with the body over here
and then over here to your aluminum knuckle
using these couple of bolts here.
Then finally we've got another lower control arm
in the front over here
that's going to control the toe.
Now in case you're wondering
the front lower control arm
has a camber bolt on it
to control the toe
and the rear lower control arm
has a cam bolt on it
to control the camber.
Now if you did want to replace the sway bar
for an N-line model one
it's pretty easy to get to
there's just two bolts that hold it to this subframe.
It is a very thin sway bar
and can definitely use some upgrading back here
along with this really small sway bar link over here
it's got a bushing on the bottom here
and a ball joint on the top here.
Now looking from behind here
at that aluminum steering knuckle
you can see you've got some bolts here
and this is the ABS wire
that go to the hub
which means that if you do need to replace this bearing
you don't need a press to change it out.
Now looking back here
Hyundai's kind of cheaped out
and went with a stamped steel rear end here
all the subframe components
and all of the suspension components
with the exception of the knuckle itself
are made of stamped steel.
Now they especially did that to save costs.
Now one thing I don't like
is that they've changed from the steel pipe
right to the rubber pipe
for the fill hose that goes down to the gasoline tank.
Now this area has the wheel
that's spinning at high speed
if something were to be kicked up
it could easily slice that hose
or if you get something sitting on the suspension
and it bottoms out
it could also damage that hose
they should have covered it a little bit better.
Now the brake setup on the Hyundai Sonata is very simple
just like many new cars today
it still has a vacuum assisted brake booster
and a simple master cylinder
there's no electric unit over here
if you follow that line
it goes down to your vacuum pump
and that's driven off the exhaust camshaft of this engine.
Now those brake lines are going to travel across the firewall
from the master cylinder over here to your ABS module
which is what's going to be responsible
for your stability, traction control
and any autonomous safety features
that your vehicle has.
Speaking of autonomous safety features
at the front here under the grille
we have our radar sensor inside of the emblem
now it sticks out pretty far in the front
it's almost flush with the bumper
there really isn't no bumper in front of it
so if you come up really fast on something
inside of your garage
you could probably crack it and cause some damage
another thing is that this hood
pretty much comes right up to the front of the vehicle
on many vehicles it's set back a little bit
so that you have a little bit of protection
in case you bump something
but in this case you could kink your hood
and damage the radar sensor pretty easily.
For example on this car
the bumper sticks out a little bit more
so you'd first hit that
and then you'd hit the emblem and then the hood.
Now taking a look at the front brake setup
on the Hyundai Sonata
things are very simple
we've got a floating single piston caliper here
that sits on this ventilated disc rotor
as to be expected in this class
the rotor itself though is e-coated
and it does have these stupid rotor screws
that Honda's been using
I really hate those
because they can often get stripped out
and stuck in there when doing a brake job.
Look at the rear brakes on the Hyundai Sonata
nothing special here
we have a solid disc rotor
with a single piston floating caliper
pretty typical for its class and weight of the vehicle.
And for the back here
you can see the electronic power brake modules
just an electric motor here
that's going to clamp these together
when you put the vehicle in park automatically
and its electrical connector up here.
Next we're going to take a look at the cooling system
on the Hyundai Sonata
you do have your coolant tank
located over here off to the side
and that actually forms part of your radiator cap
because this one is pressurized
and the radiator itself is located
underneath this plastic composite radiator support
which I don't really like
I prefer if it's actually metal
because if you do get into a collision
and this cracks
you have to replace the entire thing.
In addition, accessing the radiator itself
does require the front end to be completely removed.
Now the critical cooling component
is going to be your water pump
which is located down underneath the alternator
it is a bit tight to access
but it's possible to get it out
without removing any major components.
We do have your upper radiator hose
that's going to come over here
and go inside of the engine over here
and that feeds the back of the water pump.
In addition, teeing off of that
we do have your oil cooler
which is located right here at the front of the engine
and over here we have the other radiator hose
that's going to come up from the top here
and that's going to be fed into the back of the engine here.
Now what I find interesting
is that this has a thermal control unit
which is this plastic piece
inside of this housing over here
and that's going to house
what's basically an electronically controlled thermostat
there's a plug for it over here
which is what's going to regulate
the amount of coolant flowing through the engine
for more efficient cooling
than the thermostat could provide.
Now while we're talking about the cooling setup
the grill is pretty huge
you can see directly the AC condenser
and the air-to-air intercooler over on this side
but the cutouts are super huge
I can actually push my hand all the way inside of there
so let's say there's a banana flying up on the road
it could fit all the way through this grill
and probably damage your AC condenser pretty good.
Now the Sonata like many front-wheel drive vehicles
has three main engine mounts
you got one underneath the battery here
on the transmission side
which you can't really see
then there's one over here on the passenger side
connected to the engine's timing cover
and then there's one down below.
Now taking a look underneath the vehicle
here you can see the third engine mount
attached to the transmission over to the subframe
this is just a mount to prevent rocking
of the transmission engine assembly
when torque is applied.
And that's pretty much a look under the hood
and underneath the new Hyundai Sonata.
If you ask me I think that this vehicle is well laid out
in terms of things that you'll have to maintain
down the road that will wear out
and it should be pretty easy to work on.
However I think there are some questions to be asked
about the reliability of this
especially with that turbo engine
the durability especially with all those plastics
and the build quality
with some screws unturned underneath
that you'll have to consider
if you want to buy this long term.
Now if you are stuck in getting a Hyundai Sonata
because it is a fairly interesting looking car
you might want to consider the 2.5 liter engine
because it is going to be a little bit more simple underneath
although the Theta engines weren't really known
for their reliability
I do have a teardown video
on one of those engines linked above
if you want to check that out.
Now what do you think about the Hyundai Sonata?
Do you think it's worth buying long term
or would you return it after the lease?
Make sure you follow me on Instagram
to find out what the next car review is going to be
and subscribe for more videos just like this one.
