Ford Bronco Sport Mechanical Review

The Auto Geek
46 followers
29 Video Views·Oct 18, 2022
Today we're going to be reviewing the Ford Bronco Sport. Now unlike other car reviewers that would
battle this thing off-road, we're going to be taking a look under the hood and underneath the
new Bronco Sport to see what's inside and how it works. Now we know that the Ford Bronco Sport is
the one that's based on the Ford Escape and it's not the real Bronco. Now I've already reviewed the
Ford Escape and things are going to be pretty similar to this one so if you want to check out
that review click the link above. Now we're going to start under the hood where we have a three
cylinder turbocharged engine situated transversely for front wheel drive and then just underneath
the battery over there it's paired to an 8-speed automatic transmission that feeds an all-wheel
drive system. Now some of the other components under the hood on this side are your coolant
reservoirs, you've got your brake master cylinder over there, your battery, air box and ECU computer
off to the side. Now we'll start by taking a look at the air intake system where fresh air is drawn
in off the front of the vehicle here and it then heads down to this air box. It's then going to get
filtered out, passed through the mass airflow sensor and then sent down the back of the engine
to where the turbocharger is. So that air pipe is going to continue down over this way and then go
down towards the turbocharger which runs off the back of the exhaust of the engine here. It'll then
get pressurized and sent through this charge pipe located down at the bottom here. Now this black
charge pipe is going to come off the turbocharger with pressurized air and then come down to the
front of the engine here to this air-to-air intercooler. Now the air-to-air intercooler
is in front of the radiator on this vehicle and sits on the bottom half. It's going to cool off
some of that pressurized air and then send it back through this black tube up towards the throttle
body. Now that pressurized air is going to head up through this pipe here into this little drive-by
wire throttle body and then into this plastic intake plenum before going into the head to get
burned. Now looking at the fuel system on the Bronco Sport it has both port and direct injection.
Here we've got the high pressure fuel pump that's going to bring in fuel from the tank. It's then
going to pressurize it through this tube here and send it down to the injectors. There's going to be
three of them located down inside of here that are going to directly inject it into the combustion
chamber. Now teeing off of that we've got regular low pressure fuel that's going to head over to
this fuel rail over here for your three port injectors that are going to inject it down behind
the valves on the engine. Now of course the advantage to having a dual injection setup is
that you get the benefits of direct injection with better fuel economy and more power with the
advantage of port injection which will allow you to clean off the back of the intake valves so you
don't have to deal with any carbon buildup issues as the mileage adds up. Now looking at the ignition
system on this 1.5 liter three-cylinder engine you have your three ignition coils located right at
the top here which is fairly easy to access once you remove all of these cables so you can easily
do a spark plug change. Now also on the top of the engine you've got a metal valve cover. Most of the
vehicles have moved to a composite plastic valve cover. Now this here is your oil separator which
is going to ventilate crankcase through the pcv valve back into the air intake to get re-burned.
Now servicing the air filter on one of these isn't too difficult. Just two tabs here
and you pull it up and then I can remove the air filter. Now with the air filter box removed it
really clears up a lot of space on top of the transmission. Here you can see we've got the
that goes down to the turbocharger and here is the throttle body with its boost pressure sensor.
Now the Bronco Sport's got three main engine mounts. This one here on the passenger side which
is actually part of the timing chain cover. The other main engine mount is on the passenger side
here with the transmission and it mounts to the body. And from underneath you've got the third
engine mount. It's more of a control rod to prevent the assembly from rocking back and forth.
Now over here on the passenger side of this engine underneath this metal cover is a timing chain
which is good because you don't have to service it over the life of the vehicle. Now this is a
overhead cam engine with the intake on this side and the exhaust on this side and it has variable
valve timing. You can see the two variable valve timing oil control actuators over here. Furthermore
this engine also has cylinder deactivation so as if three cylinders weren't enough it can also
deactivate one of these cylinders. Now its solenoid is located underneath this little foam piece
inside of here. Now perhaps a little difficult to see in front of that timing chain are your
accessory belts. We've got the crankshaft at the back there and then the water pump located over
here. Now from the wheel well you can see the accessory drive belt a little bit better it's
easier to access. One thing you'll notice is there's actually no tension around this one that's
because this is a stretch belt design and you'll need a special wedge tool in order to get the belt
on and off. Now just above that water pump is where the alternator is located. Luckily removing and
servicing the alternator is pretty easy just got two bolts holding it in after you remove all these
wires in front of it. Now from underneath here we can also see the AC compressor which is pretty
easy to access. There's just a couple of bolts up at the front here and this actually drops down the
bottom. Now this engine does use 5w20 weight oil with a really small fill hole here and the dipstick
located right here. Unfortunately in order to do an oil change on a Bronco you've got to remove over
a dozen of these fasteners which are actually torx head and will probably get a lot of dirt and
corrosion in them over time in order to get this entire panel off. Look at the amount of dirt under
here anyways not like it really shielded it from anything. Now the oil pan is made of a stamped
steel design you got your drain plug over here and your oil filter located up here and just behind
that oil filter is an oil cooler that ties into the cooling system. And now we'll have a listen to
the engine startup. Now one thing about three-cylinder engines that's hard to get away from
is the fact that they're not very refined and they're very unbalanced and noisy and this one
is no exception. Right away you can definitely hear the injector clicking sounds as well as a
lot of vibration going on inside of the engine. Now I don't know if you could see that but this
engine is definitely vibrating a lot even at idle. Now all that vibration travels right through the
seat and into the cabin especially when you put it into drive. I can feel vibrations in the steering
wheel as well as in the seat. Now unfortunately there's a couple of things on here that really
reminds you that this is a Ford product. For example you can see here all of these cables
and wires and hoses are barely held in by these little foam fasteners here. Over here you can see
this is the fuel line which should be pretty dangerous if it ruptures or if it moves and it's
barely held in by this little nugget over here inside of this foam piece and you've got foam
just holding everything down. Everything in general is just so loose and I feel like these
wires could easily break because they're just not secure enough. Like on a lot of Japanese cars you
got proper clips that hold this thing down and you have to undo them with a screwdriver in order to
just get them free so you can change your spark plugs. You've also got these bare wires that are
just kind of hanging off here. I feel like this should all be enclosed in a proper conduit. You
also have to remember that this is a turbocharged engine so when it comes time for maintenance
you're going to have a lot more lines to deal with in terms of vacuum lines, coolant lines,
and some electronics running around especially on the intake side of this engine because it's
going to be a little bit more complex to work on. Another thing I also noticed as well as with the
escape is this is where your strut tower is located and this is where the outside of the
fender is located. There's a huge distance between these two where there's just an empty gap. There's
no closed out panel or anything and the edge of this fender is pretty sharp so if you are bending
over here to work on something it is going to kind of hurt you and there's a big void inside
of here. There's nothing really taking up space here. On this side they've chosen to put the washer
tank in this space however over here on the driver's side it's just left open and empty
and the splash guard isn't really preventing any mud from getting in here. As you can see whoever
had this vehicle before probably took it off-road and it's so messy under here. Now besides the
wiring mess there's actually not too much more electronics under the hood that are serviceable.
There aren't any fuse boxes under here you just got your battery and this ECU that's it. Oh yeah
and if you happen to drop this ECU you have to scrap it. Now one thing I do appreciate is this
Ford is actually using a fully stamped steel subframe and not only do they just end it right
at the control arms but they've also got these extensions here that go up to this steel bar that
comes across the front so in fact the bottom part of the radiator support is made of metal.
The radiator support at the top however is made of plastic. Now a lot of other manufacturers just
stop the steel subframe right at the control arms and the rest all Ford is just plastic which is
easy to crack in small collisions. Now from underneath here you can see the Bronco Sports
lower control arm it has a unitized ball joint which means you can't change it out you got to
change the whole control arm when it does wear out. It also uses a pinch bolt design with a
torx fastener like more German cars. Now one thing I don't like about that especially going
into the steel knuckle is that it could sometimes get stuck and be difficult to separate. Now the
knuckle itself is made of steel but that also means that you don't get bolted on bearings you
actually have to get a press in order to change front wheel bearing. Now taking a look at the
front suspension on the Ford Bronco Sport things are a little bit disappointing especially for this
being marketed as an off-road vehicle. Now we all know that this is based on the Ford Escape so the
suspension setup here is very similar. You've got your McPherson strut suspension that ties into
the steel steering knuckle. Now looking at the back here you've got your sway bar which is going
to connect to the stabilizer bar link which connects up to the strut suspension. You've got
a magnesium alloy lower control arm here which is a good thing for weight savings and then you've
got your inner and outer tie rod. One thing Ford is moving to is a lot of disposable fasteners
and a lot of the repair manuals they ask for any structural component that has to be disassembled
that you remove that hardware and discard it and get brand new hardware so that's an additional
expense that you have to account for when working on these vehicles. Now this one here being a
nylock nut once that nylon is threaded through you're not supposed to reuse it because there's
no more retaining torque. Now servicing this is going to be a little interesting the lower
control arm bolt at the back here is pretty easy to get to but the one at the front here is kind
of encased into the subframe. As a matter of fact it unbolts from the front here but you've got this
other subframe piece at the front here that you've got to remove first. The problem is in order to
remove that subframe piece you've got to come all the way up at the front here where that piece ends
and remove the bolts from the front here but that's actually tucked underneath the bumper skin
so now you've got to remove the entire front bumper clip in order to change a lower controller.
Overall the McPherson strut suspension is going to be good for long-term use because it's not
going to wear out as fast as a multi-link design however it's not going to be as good off-road.
Now here's a look at the rear suspension from underneath you can see this giant trailing arm
here that connects with the body over here actually comes right up to this point here
and forms part of the knuckle itself with the knuckle also being stamped steel instead of a
cast or forged piece. Now looking further inside of there you can see the bolts for
the bolted on rear bearing so that means you don't need to press to change this one out
unlike the front one. Now here's another look at the rear lower control arm that carries the spring
you can see we've got a cam bolt over here the control arm is made of an aluminum that looks
like it's been hydroformed. And here's a look at the sway bar link which connects to the knuckle
and then out to the sway bar which connects to the sway bar bushings to the subframe. Now not
surprising the subframe itself is made of a stamped steel design so just make sure you get
this car rust-proofed especially if you're going to take it in salt waters off-road. Now here's a
look at the front lower arm it's a really thin small link now all it does it really keeps the
knuckle in tow. Now taking a look at the Bronco Sport's rear suspension design you can see that
we do have a multi-link design here which is somewhat disappointing this being an off-road
vehicle would be cool if you had like a solid axle design but we all know that the Bronco Sport
isn't the real Bronco. Now taking a look at some of the arms here you've got your trailing arm here
you've got another steel arm here that's your upper control arm and then at the back here you
have the rear lower control arm which fetches the weight of the spring as well as the shock absorber
down here. Now a rear multi-link suspension isn't a bad thing to have for a crossover style of SUV
at least servicing it shouldn't be too difficult you've got your two bolts at the top there and
then one bolt at the bottom here for your shock absorber the spring likewise can also be swapped
out especially for those who might want to put a little lift on this your control arms are also
pretty easy to access all the bolts you've got your bolt here for your upper control arm over
here the trailing arm itself is actually integrated into the knuckle as one stamped steel piece look
how much mud is caked up inside of here I wonder if they should have gone with a simple plastic
splash but you could just power wash instead of this furry carpet stuff. Next we're going to take
a look at the eight-speed automatic transmission in the Ford Bronco here you could see we've got
the valve body in front here which is this plastic piece now there is no dipstick to check your fluid
quality or the level instead this is a transmission fluid vent and that's going to become your fill
port when you change the transmission fluid. Also on top of this transmission is your gear selector
which is going to be powered by an electric motor because you do have that dial switch on the
dashboard and that's going to select between park reverse neutral and drive. Now because the Bronco
Sport has this digital dial here to switch gears it's going to need an emergency release to take
it out of park in case it's stuck so you'd have to pull on this little guy here and that will allow
you to pull it out of the mud where this doesn't belong and send it off to the insurance company.
Now while I sometimes complain why the ECU is located under the hood subject to a lot of collision
damage check out where the transmission computer is located down inside here underneath the headlight
where the fog light is located so if you get into a minor collision or you run over a bump in your
Bronco it's probably going to be really easy to damage and really expensive to replace. Here's
another look from down below at those wires that lead up to the transmission computer. Now the
starter motor on the Bronco is located down underneath the intake down inside of here. Luckily
there is enough room to kind of get around here once you do remove all these wiring harnesses
in order to get it out without removing any major components. Now here's a look at the transmission
from underneath you can see we've got our drain port for the transmission fluid here. Now once
your 8-speed automatic transmission has done determined what gear it wants to be in it's then
going to send it out to the front differential out to the front wheels. Now some of that power is
going to be sent over to this transfer case for the all-wheel drive system. Now what the transfer
case is going to do is going to take some of that transverse power and send it down this center drive
shaft which is going to go down to power the rear wheel. Now just above the transfer case you can see
this electric motor which is responsible for activating and deactivating the all-wheel drive
system. Now just next to the drain plug is a transmission warmer and cooler assembly over on
the driver's side. Now that drive shaft is going to send its power out to this rear differential
which is going to distribute it to each wheel. Now on this model it just has a standard differential
but on upgraded models it has a torque vectoring differential which can vary the amount of torque
that goes to each wheels individually to help you to corner better and for better off-road ability.
Now the differential's got a fill plug over here and a drain plug located down here because you
have to replace that oil as well. Here's a look at the drive shaft as it comes into the pinion gear
into the differential and you can see that it comes to this really narrow neck here. Now i'm
wondering if that's an engineering decision to make this neck really small so this becomes your
snapping point instead of something else going in the system that's a little bit more expensive to
replace as if a three-cylinder turbocharged engine has enough torque to snap the rear drive shaft.
Now let's be honest we all know this is pretty much all Ford Escape underneath but for a vehicle
that carries the Bronco name look at the size of how small and tiny these rear axles are it's
almost the size of my wife's old toothbrush. Next take a look at the cooling system of the Bronco
Sport starting here with your expansion tank you've got the radiator cap which is relocated
over to this expansion tank so it's also pressurized and then the lines come down inside
here the radiator and the fan is all located as one assembly in the front here and unfortunately
if you do have to replace your radiator the entire front end of this vehicle including the
headlights and the bumper have to be removed in order to access this as a full assembly. Now just
down below the alternator looking at the mess of coolant hoses here if you follow this coolant hose
it'll actually go to your thermostat housing which houses the thermostat just in and behind the water
pump driven off the pulley you will have to remove the alternator in order to access both the water
pump and the thermostat to replace it. Now the water pump is belt driven located down inside of
here there's a couple of bolts you have to remove the pulley and then you can get it off of the
engine block. Now the Bronco Sport has these active grille shutters that are there to close at high
speed for better aerodynamics and open at low speed to allow mud to sling all over your engine bay.
Here's another look at the active grille shutters on the inside here you can see these flaps that
are going to actively open up and close to cool the engine. Now the Bronco Sport only uses a single
cooling fan behind that radiator. Now in addition to your coolant hoses that are going to come off
the radiator you've also got two extra coolant hoses that are going to go into your heater core
as well as down to the turbocharger to keep it cool as well. Now right next to the oil filters
this auxiliary water pump which is electrically actuated that'll allow you to circulate the coolant
inside to have heat and also to cool it down after the engine has cut off especially on a turbocharged
engine that's pretty important. The only thing I don't like is how this connector is just kind of
exposed ready to be whacked off in case you hit something underneath. Now the exhaust setup on the
Bronco Sport starts at the back of the engine down over here underneath this air intake pipe where
you've got this integrated manifold here that's going to flow directly into the turbocharger
it's then going to flow down into the first catalytic converter. Now from underneath you can't
really see the turbocharger but you could see the back of the catalytic converter over here
which is then going to send exhaust down to a secondary catalytic converter and then to a
front muffler. Now after the front muffler the exhaust is then going to come through this tail
pipe out to this muffler here at the back which has dual outlets one on that side and one on that
side and it's actually surprisingly hidden by the bumper here there's no real effort to bring it out
and make it really throaty and flashy. This car's got only 4,000 kilometers and a lot of soot out
of the exhaust and now we'll have a listen to the exhaust. Now taking a look at the braking system on
the Bronco Sport you have this brake booster actuator assembly inside of here now this is all
one big unit so you've got the brake booster part on this side here that uses an electric motor
there's no vacuum assist anymore in order to press the brakes that's why it kind of has an unnatural
feeling to it. Your master cylinder is all integrated inside of here so this is going to be
pretty expensive to replace because you gotta replace the entire unit if your master cylinder
goes bad and you're also going to need a scan tool to specially bleed this out. Now on this half over
here is your abs actuator you can see the four lines that are going to go out to the wheels
individually there's no separate abs actuator. Now this module is also going to be responsible
for any stability and traction control as well as any safety features such as the pre-collision
system that this vehicle has. Now taking a look at the front brakes on the Bronco it's kind of
disappointing you've only got a single piston floating caliper on a ventilated disc rotor
with a vehicle of this size you probably should expect a dual piston front caliper. Now taking a
look at the rear brakes on the Bronco Sport you do have this solid rotor here and it is coated
which means that it won't rust you've also got a floating caliper here and on the back of it
you've got an electronic parking brake. Now this thing's absolutely coated in mud as a Bronco should
be because it's supposed to be an off-roader but this here is where the gas tank is located
it is a plastic unit and you can see the fill tube for it over here. And that's a wrap on the
mechanicals of the Ford Bronco Sport. Now overall I think it's a good idea in the market to have a
uniquely styled and themed crossover vehicle to separate it from all the other boring ones out
there. Now under the hood of the Bronco Sport just like the Ford Escape I reviewed I think Ford's got
a little bit of work to do in terms of build quality reliability as well as some easy maintenance
items so that someone could actually consider keeping this vehicle long term. Now you tell me
in the comment section down below what do you think of the Ford Bronco Sport? Is it a good addition to
the Bronco lineup or is it really just watering down that brand name so that Ford could pass off
a small size SUV to compete with the Jeep Renegade? Now make sure you follow me on Instagram to find
out what the next car review is going to be and subscribe for more videos just like this one.
