1964 Jeep CJ5, Engine Stuck, Will it Run and Drive???

Norman's Architectueral Design
24 followers
20 Video Views·Oct 18, 2022
Hey everybody, welcome back to Diesel Creek. My name is Matt. Today we're going to be getting
back onto a project that a lot of you have been requesting. That's right, underneath of this tarp
is a one-owner barn find 1964 CJ5. Oh, what a sight for sore eyes. Now if you haven't seen the
first video on this Jeep, the link to that video is down in the description and if you take a
gander at it before you watch this one, you'll probably get a lot better understanding of where
we're at and the challenges that we're facing. But just to sum it up for you, I found this thing
sitting in a barn. It had not been touched in probably 20 plus years. Once I was able to drag
it out and drag it home here, I found out the engine was locked up and after some playing around
I was able to get the engine turning again and by the end of the last video I was able to get it to
pop off on some gasoline just poured down the carburetor. But there's a whole host of issues
that we're going to have to tackle before we're able to get this thing really running correctly
on its own again, not to mention driving down the road. But by the end of this video, that's where
I'd like to be. So let's see if we can't breathe some life back into this old thing. Oh, I know the
old Jeep's still a pretty good little ways from driving under her own power but this is one of
two tires that actually hold air out of the five that I have for this thing. So I bought some new
tires because I'm anticipating being able to drive it here very soon. So I'm going to yank the wheels
and tires off right now and I'm going to take them down to the uh the tire shop there and we're
going to get working on the rest of this thing. I almost forgot, driver's side is reverse threaded
on these things. One down, three to go. All right, we're back from the tire shop. Ended up going with
these DeStone 503s. I like this old tread pattern here. This is a 7x15 tire and uh yeah I don't know
about this tread pattern. You used to see these on all kind of old vehicles back in the day. Cars,
tractors, everything. I think uh the only thing I don't like is I think we should have gone with
like an 8x15. Seems like the treads here and the tire is kind of pulled out to the rim but
is what it is. That'll be fine. So I've had this thing sitting around here for over a year now
and uh I've never seen it with four inflated tires. Man, I think those tires look sharp on
there too. Like I said, I wish what I wish I'd have gone a size or two wider but uh yeah they
look good. I'm happy with those treads and everything. I originally mounted that front tire
backwards. I didn't realize they were directional until I had three of them on. Well now that we got
some good shoes on our feet, I suppose we should probably spend some time on the engine here.
Tires are no good if the thing won't drive. You can see the mice have been at it again.
A whole bunch of junk falling out of the hood there. Anyways, I think uh I think I'm just going
to go ahead and pull the carburetor off of it right now and we're going to take it home and
let it soak for a little while and then go through it. I have a carb kit and uh yeah then we'll
reinstall it. There we go. Ta-da! There's that guy right there. We're going to uh take this thing
home, clean it up. Got one more screw to pull out here then we can separate the halves of this
carburetor and we're going to put it in the dip. That's right my dear! You guys ready to see how
crusty this carburetor is in here? I've got a feeling like this has maybe potentially never
been opened up from the factory. I have no way to prove that. Wow. I mean it's definitely dirty but
you know what? It's really not that bad all things considered. Wow. Floats, floats stuck.
So that's cool. It's not that bad. I'm gonna let this thing soak overnight and tomorrow we're
gonna rebuild it. Let that drip dry a second. Seems like the float's moving a little more
free today. Pin, float, doesn't have any fuel in it. Not too crusty. Yeah this top half of the
carburetor really doesn't look too bad. I blew it all out really good with the air compressor
there. All the ports are clear. The only thing I think we have to do here is clean off this old
gasket material and this top half's pretty much good to go. All right that's that's pretty much
good to go. Moving on to the bottom portion of the carburetor. This is more the business end here.
This is where all the dirt was and everything. Uh yeah. So this should be our accelerator pump
and it appears to be seized up. This thing should move up and down
yet it does not. So this linkage goes up through the body of the float bowl and everything and
nothing nothing pivots there like I believe it's supposed to. Look at that. That's always one of the
things that I really enjoy about cleaning stuff up like this, this old stuff. You just get to uncover
all the old writing and stuff and you never know what it is. I mean a lot of times it's just casting
numbers like something like that there but Carter YF made in the USA. I like to see that on stuff
but you don't see it too much today unfortunately. So this accelerator pump plunger is seized up
solid in here and I don't think I have any of the replacement parts for this thing in the kit
so I've got to be super delicate and try to get this apart and freed up and working again without
destroying it in the process. These particular parts here that are seized up
are not terribly rusted or anything but they are the only rusty parts that I've seen
so far in this carburetor. Hopefully I can get everything freed up and moving again without too
much trouble here knocking things off. I hope you guys saw how that went together because I'm not
positive but I got an idea. A little tappy tap got her freed up again here. Yeah look at that.
Maybe not quite like the day it was new but
there we go. Tell you what the diaphragm doesn't even look as bad as I thought it
would be. I'm sure it needs replaced. It's definitely cracked up and stuff but
usually these things sitting as long as this thing has they disintegrate.
All right she is done. I am feeling good about that.
Let's go install this thing into the Jeep. Oh I'm missing a screw. There it is. Now it's done.
Let's install a carburetor. Tell you what before I try to pull that old gasket off of there I'm
going to take the compressor and blow the whole top of this engine off like I should have done
before I even removed the carburetor but better late than never eh? Now we're ready to put this
thing on. There we go. So there's two control cables that come out here. This top one is for
our choke. The bottom one is just a throttle control so you could kind of use it kind of
a cruise control but you shouldn't do that but you could just kind of hold the throttle at a
steady rpm. They're both frozen up so we're just going to ignore those for right now. I just put
them on there so they're tied up nice and tight and not bouncing around in here. Now a modern
vehicle we would have a paper type air filter element that would go straight on top of this
thing and the paper element filters out all the dirt and the paper element would filter out all
the dirt and contaminants from the atmosphere but in this old girl we have what is known as an
oil bath air filter so basically how this thing works is it sucks in air around here draws it
down through and this bottom bowl here which I'll pull off in a second this bottom bowl is full of
oil about up this high and it pulls all the air through the oil and then up into the carburetor
that actually works very well at pulling out all the contaminants from the air the downside of
these things is that they're a little bit messy you can see how you can see how greasy this one is
and it also has to be changed pretty regularly it's a lot of maintenance you're supposed to
change the oil in these things like every like 15 hours in dusty conditions something like that so
it might be more for something that's on the road but I know heavy equipment it's supposed to be
like 10 to 15 hours yeah so we can see how black that nasty old oil is there we're going to dump
this out and put some fresh stuff in it before we try to uh start this thing up oh man yeah this
thing is dirty all right I got this thing all cleaned out nice and you can see right there it
says oil level so you basically just dump oil in it until it fills up that line and reinstall it
I usually put straight 30 weight oil in these things but as far as I know any engine oil should
be fine all right now as you can see I left the fuel line off here and that's because the entire
fuel tank and the fuel pump and the fuel lines in between them all really need cleaned out very well
before I try to pump this carburetor full of dirt so I'm going to try to run this thing off of a
temporary tank today and uh if everything goes well then I'll spend the time and effort cleaning
out the rest of this fuel system all right we are getting pretty close to where we could try
to start this thing now before I do that though I want to change the oil on this thing now now
usually I'm an advocate of even on something old like this with really old oil in it as long as
there's no contamination in the oil I prefer to run the engine with the old oil get it warm and
then drain it this time I'm not doing that because if you remember in the first video when
the engine was locked up I got it to break free by using some rust remover chemicals that I dumped
down inside of the cylinder and I believe probably most of that stuff wound up in the oil pan so I
have no idea what that would do to the oil or any of the other stuff in the pan so I'm going to go
ahead and drain this thing I should have done it last year to be completely honest with you
but uh better late than never so I'm going to drain that out put some fresh 1540 in this thing
and then we're one step closer well the good news is the oil actually looks pretty good
I don't see any obvious contamination in it doesn't smell like it's full of gas or anything
yeah I like it I have hopes for this engine this uh this oil filter seems like it's going to be a
mess no matter how we do it holy crap is that thing on there too
look at that it wasn't nearly as messy as I thought it would be all right got that all topped
off I think we're getting ready to go here I don't see any antifreeze in this thing or water at all
and the radiator's definitely seen better days I'm gonna put a gallon of water in here and see
what happens see if we're leaking anywhere hmm well the good news is I don't see it leaking
anywhere well I just reminded myself that in the last video that solenoid on the starter there
dead shorted and now when you try to connect the battery to it it uh it just tries to arc out but
it doesn't spin the starter so uh luckily I have one of those solenoids just laying around here on
the shelf so I think I have to pull the starter to change that out unfortunately I can't get to
the screw on the back side so there we go we got the new solenoid put on there and if you'll recall
in the first video on this jeep we could never get the engine to crank over using the key switch
but since the solenoid's replaced and now now the key works so I'm gonna rig up a temporary
tank on this thing and I think we're gonna go for it man that's a dirty windshield huh
figured I'd clean that up first because I'm gonna hang the fuel tank right here
a little easier to clean beforehand all right I wasn't gonna do this right now but it's bugging
me I have to I think being able to fill up your fuel tank from the passenger seat is a great idea
with all that done I think we are finally down to the moment of truth here will this thing fire up
and actually run and idle this time in the last video we did get it to pop off for just a few
seconds dumping some gas down the carb but uh really didn't get it to run for more than I don't
know five seconds it was it was nothing substantial so first start run and idle and then if it idles
good we're gonna tune the carburetor in a little bit and uh yeah we'll finally get to drive this
thing that's the part I'm really excited for we didn't think it'd be that easy did you
it's dumping fuel out the bottom of the carburetor there what I think is happening is the bowl is
overrunning and it's coming down through that little lever that has a pass through through
the carburetor I reset the float again I've actually got it adjusted a little bit higher
than I think it should be so yeah hopefully it works this time I went a little higher
because I already had it where I thought it should have been when I put it together the last time
clearly not all right I think I got the float adjusted right this time I must have bent it I
guess when I reinstalled it before because it's just a hair lower than I had it at reassembly
and it appears to be working now that means we're ready to fire this thing up or at least
try to all right well it's the moment of truth here close off that choke see if this baby's
going to fire ready contact might have something here and contact I just noticed that the throttle
was stuck wide open all right I just pulled a plug out to check and make sure we're getting
not seeing any spark that could be our problem just got to pop this cover off and clean the
points again real quick we did it last year but apparently they oxidized up again it's a
little hard for you guys to see this but all I'm doing getting this file in between these
two contact points go back and forth until we get that cleaned up all right so we definitely
have spark now I am uh feeling pretty confident that this thing is going to fire up now you guys
ready dying down well she stumbled and died there but man it ran that's the longest I've heard it
that's exciting try this again
why are you not running now
can't tell if it's getting too much fuel or not enough
she's a smoky mess but I figured it would be
I'm so tickled to see this thing actually sitting here running
this is awesome well it runs it's time to see if this baby's gonna drive I'm so freaking excited
uh the driver's seat has seen some better days she's plush having a little mud flat can't fix
yeah oh this thing is sweet all right first drive in who knows how long
or at least first attempt at driving where's first we got over and back is first oh it went in
oh it wants to go
it moves
look at all the crap that we blew out of the exhaust
plowsers man for the first time and the good lord only knows how long
driving around under its own power I've got that rag wedged under the hood there so we don't pinch
off the fuel line but it it really sounds good and it's clearing up it's already gotten a lot
less smoky let's take this thing for a little rip just chugging along in high range there's
the first sign of not good I can smell antifreeze I think that might be confirming what I suspected
from the beginning was there's a head gas control uh-oh we got trouble hurry up and
get it back over to the shop smelling antifreeze big time now oh yeah I thought I was smelling
antifreeze she spoiled over on us maybe I'm wrong maybe it does better shut her down
I had this thing full up to the top with water and you can't see any water in it now
I mean obviously there's still some but uh I'm thinking it probably burnt a good bit of it it's
probably sucking it in and yeah we're gonna need to do a head gasket but it seems to be worth doing
the thing actually runs really good the smoke all but cleared up there at the end I was wanting to
get more driving around footage with it but uh I don't think that's probably too smart since we're
overheating it and but I don't think that's probably too smart since we're clearly overheating
I'm gonna let this cool down for a minute I'm gonna go ahead and let this thing cool off for a
little bit and put my tools away and after it cools down a bit I'm gonna go ahead and fill the
water back up and I'm gonna run it and we're gonna watch and see if we see any compression bubbles
coming up through the coolant and I'm pretty sure that's what we're gonna see but the carburetor
seems to be dialed in just right but the carburetor seems to be dialed in just right so I'm quite
happy about all that all right well I let this thing cool down for about a half an hour here I
put three quarters of a gallon of water in it because that's all I had yeah doesn't look like
you guys can see there we go so I'm gonna fire it up now and we're gonna watch and see if we get any
bubbles up through the radiator contact oh yeah yeah she needs a head gasket yeah so we're getting
a lot of bubbles up through the radiator hopefully it just needs a head gasket and there's nothing
cracked like the head or the block so that means we still have some work ahead of us but man
it is there and it wants to run I am so freaking excited about this thing I know I keep saying it
well I'm gonna have to close the hood on this video for right now there's plenty of work left
to do on the old jeep but the the concept is there the thing runs it actually seems like the smoke's
cleared up awful well the more I run it I'm sure the better the smoke is going to get what happens
when an engine gets stuck is usually the ring sees to the cylinder walls well the rings also
seize in place on the piston so they're not filling the entire area of the cylinder wall
so as this thing comes back around the more we run it the more those rings are going to
loosen up and start doing what they're supposed to do which is seal off the gap between the piston
and the cylinder wall and that's going to increase compression as well as keep that smoke to a
minimum so the next video on this old girl we're going to be definitely putting a head gasket in it
well hopefully it's a head gasket hopefully there's not a cracked head or a crack in the
block somewhere that's letting that compression into the cooling system but in the next video
we're going to be looking into that we got to go through the fuel system clean out the fuel tank
maybe seal it up the fuel pump on the engine it has a mechanical fuel pump we got to go through
that thing and make sure it's not letting fuel bypass down into the oil and then we got to tackle
the entire brake system because right now the pedal just goes right to the floor and stays right
there sort of like stepping on a plum even though we got all that work ahead of us I am still super
stoked for how this thing is turning out I'm really excited to be driving this thing for the
first time and I can't wait to drive it again so if you guys want to stick around and see some more
videos on the old jeep make sure you're already subscribed to the channel so you don't miss a
thing if you like the video do me a big favor hit that thumbs up button down below it really lets
me know that I'm doing the right track making the videos that you guys want to see and it helps me
keep doing what I'm doing lastly if you want to help support the channel head on over to diesel
creek.com the link's down in the description pick yourself up a nice hat stylish t-shirt sticker
pack beer koozie what have you and you'll be looking good and helping support the channel
at the same time so thank you guys for watching and I will see you on the next one later
