Make a Bonsai Bench/Traditional architecture of countries

Traditional architecture of countries
159 followers
36 Video Views·Oct 8, 2022
See how to build a cost-effective bonsai bench, using off-cuts of pressure-treated timber. Subscribe for more Japanese garden updates.
Tools used to make the bonsai bench:
- Mitre saw
- 6mm wood screws
- 3x2in, 2x2in & 2x1in wood
Cre: The Japanese Garden
A couple of years ago I made this garden shed in the style of a Japanese tea house and you can see
there's a bit of an area there for seating with friends, a bit of a garden shed off the side of
that where I keep the lawnmower, garden tools, all the rest of it, but inevitably when you're
working on a project like this you will get a bit of waste in terms of the wood used.
Slate roof, that's fine, I ordered that pretty much to perfection actually,
it worked out quite well, but wood offcuts inevitably are going to be a bit of waste,
so I don't like waste so I'm going to put all of the wooden offcuts I've got
left over from this project to good use and make a bonsai bench on the cheap and I'm going to
explain how I'm going to do that right now, so let's get started and head over to the workbench.
There's a miter saw here which is great for cutting 90 degree and 45 degree angles just
to make sure that they're all accurate and precise, I've got two cordless drills,
one set up with a four millimetre or five millimetre diameter bit just to counter to
produce a little pilot hole for the screws so that we don't split the wood and then there's
a countersink bit there that you can see as well just to make sure that the screw heads are nice
and flush and timber, choice of timber, we've got some western redwood cedar here and now obviously
this is a very dense hardwood and it's a little bit left over from when I was doing the the fence
posts a couple of years ago so I won't be using that because I've got enough of it, this is
pressure treated timber, this is a copper sulfate bath which is put under high pressure and forced
into the timber when they produce this and it makes it quite weather resistant which is great,
it's just ordinary pine but it makes it last a little bit longer outdoors so that's advisable
if you're going to choose a particular type of lumber and I've got some untreated timber here,
this is left over from an old airing cupboard that used to be inside the house, so I'll be
using these and cutting them up for the laths for the top for the table, so there you go that's a
little selection of different types of material that you can encounter, if you can go for hardwood
go for it but obviously it's going to cost you more but in any case I'd advise you stain it and
weatherproof it just to make sure that it's weather resistant, so let's get cracking.
So this is where I'm at so far, this is the amount of timber that I've had spare so that's
going to be the limiting factor in making the bench, it's four foot in width, in length rather
and just over two and a half feet high and in width the base is just 19 inches so one of the
things you've got to think about when you're making a bench is it's got to be sturdy because
obviously the bonsai parts you don't want them falling off in the wind so the width, if I could
have gone a few extra inches I would have done but that's just been the limiting factor on the timber
it's got cross bracing just to make sure that it's all strong
and the tops again just come from that airing cupboard, this is the non-pressurized untreated
timber so I'm going to make sure that it's got plenty of wax coating on it to make sure it's
protected and I'm just cutting these down in length from the sort of 70 or so centimetres
that they were down to two foot in width just to prevent it from overhanging and toppling over, so
I'm going to get screwing those down but I'm going to get screwing them down with some screws from
this box, now I'm just going to show you something over here, you just bring the camera in over here
and I'll just show you the contents of this box, so this was bought at an auction place
for about 20 quid and that's all of the screws that you see inside the box,
nuts and bolts there excepted because that's different that's from a car project and left
over but these boxes of screws traditionally if you went over the counter they would cost
anywhere in the region of six or seven quid just for a box especially these wide diameter ones,
these are six millimetre threads on these and there's literally boxes and boxes of screws that
I got, I'll put the link in the description below but this is how you can save money on a project
quite easily and these are all yellow zinc passivated so this is a better treated surface
than the just plain zinc but obviously you're going to stain it anyway to make sure that it
doesn't rust, if you can get hold of some stainless fasteners like these for instance
that's even better, the copper sulfate can have a tendency to rob the zinc plating from your
steel screws a little bit faster outdoors so if you can use stainless fasteners that's even better
but obviously they cost more than your standard fasteners that you find but it just goes to show
that if you hunt around for a good bargain you can get some good deals out there, hearing protection
required, these are the old nails that need removing and there's a bit of rot in the wood
there so we'll just get rid of that to start with, 50 inches so we'll mark it off 20 inches
at the end and then we'll mark off whilst we've got the tape measure out we'll mark off the
halfway mark at 10 inches as well, that's the one we're going to use to align them on the bench
and the next stage obviously is the sanding of the wood, I want to get rid of all of this old
surface where there's been a little bit of weathering on it because it's been under the
bench and the best sander is really a belt sander, they're quite aggressive but in terms of cleaning
off wood back to a clean surface there's nothing better really so I'm going to stick this upside
down in a vise later on and just belt sand all of these one at a time and I'll just show you
that process later on. Okay so it's time to stain the bench now and I'm going to talk through the
different types of stain that you can probably encounter, I'm not teaching you how to suck eggs
here but it's just from experience really, this one is a solvent-based one, this one is a water-based
one, the water-based one is cheaper than the solvent-based one and I always find from experience
that the solvent-based one lasts a lot longer on the timber than the water-based one, so if you
want to go in bulk and you don't mind repainting your fence every year or whatever you're making
you can go for the water-based one but for longevity I always prefer the solvent-based one.
This one is a teak colour from Sadeline, a good brand and I tend to use it just to play with an
old brush, this is a one and a half inch brush, it's seen a bit of wear but it'll do for the job
so let's get staining. So there you go the bench is now complete, I think it must have cost about
five pounds in total in terms of materials. If you've made a bonsai bench before then perhaps
you'd like to let me know how you made yours in the comment section below and if you want to see
how I made this tea house then feel free to click the subscribe button and you'll get a
notification when it goes live. Until next time, take care.
