Today, on Workshop Edits, I'm showing how I built my 7-sided "Heptagon" arbor that I used at my wedding. My fiancé wanted something unique, and so she got it!
📲 Check me out on SOCIAL MEDIA! INSTAGRAM: instagram.com/workshopedits FACEBOOK: facebook.com/workshopedits
Thanks for watching! Zach
Today I want to show you how I built this seven-sided heptagon arbor for my wedding. I started
off this project by measuring and cutting down four 4x4s that I got from my local lumberyard.
I wasn't sure really how big I ultimately wanted this thing to be but decided that cutting each
side to be 40 inches would be sufficient. That would give me a maximum width of 7 feet which
seemed big enough for a wedding arbor but not so big that it was impossible to transport or just
look kind of funky with us standing under it. 4x4 lumber can be kind of rough. I did my best to find
the best quality stuff but ultimately it wasn't great looking on the surface. I ended up running
all four sides through the planer a few times. It was almost enough to get rid of the rounded edges
on each corner and then I carefully selected the best face of each piece to represent the front
face of the arbor. Next up was cutting the angles on each piece. Now seven sides is probably the
trickiest shape you could make because unlike something that has five, six, or eight sides,
seven doesn't divide evenly into 360 degrees. I needed to cut angles at about 25.7 degrees on each
piece so that when you added up all 14 sides it completed the heptagon. Now I did my best here but
it definitely was not perfect even with a miter saw and I'm not sure why I chose to cut the miters
this way. I should have just kept the saw perpendicular to the cutting surface and just
angled it. Only after did I realize how much more difficult this method was. Now after cutting all
14 angles I laid out the piece and decided which of the seven sides I wanted my base to be. Then I
went around and labeled each piece and made markings of how much more material I needed to remove to
refine the angles so that everything in each joint matched up perfectly. In reality I should have
just gone back to the miter saw to refine this but instead used the stationary sander which worked
but it was a bit more time consuming. Now I wanted to use dowels for this project to connect things.
These would provide strength as well as help align everything when assembling and ultimately I wasn't
sure if just the dowels would be enough to hold things together but I went for it anyways. Using
a $20 doweling jig and a clamp I cut half inch dowels into each of the mitered corners and then
cut out half inch dowels and rounded down the edges. And I did a test fit to make sure things
were good and then could begin assembling each side. This was actually really tricky to clamp
and there really wasn't a good way to do it by myself. I tried using this angled clamp from
Rockler and they were pretty helpful actually as the dowels would help keep things aligned
while I clamp things down but ultimately I ended up using two to three three inch wood screws on
each end and that not only really strengthened this thing but it really helped pull everything
together. Now we wanted the base to be pretty simple as we didn't want it to distract from the
beauty of the arbor. Something built just from two by fours with tapered edges. I broke down a two
by four that I had into two pieces that were about 40 inches and then planed it down to clean up the
sides. I then made arbitrary tapers on the front and back of the piece and the only direction I
followed for myself was to make the front taper about two thirds as long as the taper in the back.
Again just going for minimalism on the entire base. Then I used my taper jig to make repeat
cuts on the table saw to get even tapers. Now my plan all along was to use half lap joints on the
base to attach the legs. I thought it would look kind of fancy and ultimately it would just look
clean. I carefully marked out and measured where each leg would go and then took my four by four
over the table saw to begin cutting the dados. Using a cross cut sled for this made it really
really easy to make all the cuts equally and safely. I then went and repeated a similar process
with the legs, again just cutting dados so that they would marry the dados in the base that I had
just cut. To assemble, I measured, marked, and drilled a few countersunk holes in the base so
that the screws could be recessed up from under the legs. And I also drilled pilot holes to avoid
splitting the wood. Now I have never used a router table before this project but I finally got one
and I thought it would look neat and subtle on the base to add a small bevel to all of the edges.
So I went over to the table and routed those out. Again, it wasn't necessary but to me it
made a really big difference in the subtlety of the design. Last up was sanding each piece,
lots of it. Mostly the joints and the edges as they were no longer rounded pieces of stock
and rounding over all of the corners at the joints really made everything come together
smoothly and almost hid all of the mistakes that I had made due to the angles being so complicated.
After sanding, I assembled the base. I added glue, fitted in each base piece to its matching dado,
and then drove in my screws and it felt rock solid. Now we ultimately wanted this wood to
look like cedar. Now I live in Southern California and cedar wood is near impossible to come by so I
ended up using some red chestnut stain to bring out that look that I wanted. And in my opinion,
it was exactly what I wanted and had envisioned for the project. One thing I didn't mention is
that I ended up making this so that the arbor could break down into three pieces. Those being
the two sides that were three edge pieces each and then the base. And I just kept the dowels in
the pieces that way it could be transported and then easily lined up and assembled again at the
venue. And for me this was a necessary step as I had to transport this thing about 250 miles and
there was no way I was going to be able to fit this thing even with a trailer with it being over
seven feet wide. And now that I was finally finished with this thing, it was time to pack
it all up in the trailer with the rest of our stuff and head up north for the week of our
wedding. And it only took about five minutes at the venue to set up with an impact driver once we
got there. And once that was done there wasn't much else to do but enjoy the big day. And here's
just a quick teaser of how it played out. Zach, give me a kiss your bride. And I'd say it was easily
the best day of both of our lives mostly because this thing didn't tip over and fall on us mid
ceremony.