【彫刻刀の研ぎ方】 丸刀編 初心者向け 砥石を使っての刃物研ぎ 【手砥ぎ】

Japanese Woodcarving TAKABA
5 followers
砥石を使った丸刀の研ぎ方を動画で解説していきます。
彫刻用の刃物は同じサイズ同じ形の刃物であっても用途によって様々な砥ぎ方をします。今回は木彫に必須の丸刀を砥ぎます。
丸刀はプロも機械を使って研ぐ事が多いですが砥石でも勿論研げます。しかし平刀と違い納得のいく確立された研ぎ方がなく、実際私の研ぎ方も誰かに教えてもらったものではなく思考と実践を繰り返して自身で作りました(現在も思考と実践を繰り返しています)。
そのノウハウをこの動画でお伝え出来たらなと思います。
*音と滑舌は悪いです💧
ホームページ→https://mokuchotakaba.com
Twitter→https://twitter.com/BachinM
#woodcarving #woodworking #woodart #art #彫刻 #木彫り お問い合わせは [email protected] まで。Credit: Japanese Woodcarving TAKABA
In this video, I would like to sharpen a round blade with a sharpening stone.
Professionals often sharpen a round blade with a buff, but a sharpening stone can also be used, so this time I would like to make a video of how to sharpen a round blade with a sharpening stone.
In my case, I use a flat sharpening stone because it is difficult to sharpen a round blade with a burr.
The most important thing when sharpening a round blade or a flat blade is the feeling that the sharpening stone and the blade are closely attached.
If you don't have this feeling, it's not a good way to sharpen a round blade.
Sometimes it's easy to sharpen a round blade, so I dare to sharpen a round blade, but this time it's basic, so I'd like to practice straight sharpening.
Hold the edge of the blade with your right hand as close as possible to reduce the burr, and press the edge of the blade with your left index finger to the sharpening stone.
If you don't have this feeling, it's not a good way to sharpen a round blade.
Basically, the way to sharpen a round blade is the same as that of a flat blade.
I also made a video of sharpening a flat blade, so if you haven't seen it yet, please refer to it.
In particular, when sharpening a round blade, the sharpening stone and the blade are closely attached at the pin point, so it is very easy to mess up the sharpening surface.
Therefore, I think it is better to reattach each blade.
By the way, the blade I'm sharpening now is not actually a carving knife, but a small tool.
This small tool is a blade that is in the middle of a carving knife and a chisel.
Basically, it is used for finishing as well as a carving knife, but it is not very common, so I wrote it as a carving knife in the title and description column.
In the video of sharpening a knife, it is often seen that it is done by pushing and pulling, pushing and pulling.
In my case, I only do it when I push.
Push and let go of the sharpening stone.
By doing this, you can reduce the blur between pushing and pulling, so it will be easier to sharpen straight.
However, in the case of pushing and pulling, it can be sharpened when pushing and when pulling, so it takes time to shorten.
However, if you only push, it will take a long time to sharpen, so I will start sharpening from 800.
This completes the sharpening in 800.
Next is 1000.
I think that sharpening is the most important thing when sharpening a knife.
As I mentioned earlier, when sharpening a chisel, it is common to sharpen with a chisel with a groove.
However, if there is a groove, it will be difficult to sharpen the surface straight, so I sharpen with a flat chisel like a chisel.
By using a flat chisel, you can easily sharpen the surface using a diamond chisel or a re-attached chisel.
The reason why I use a flat chisel is that the blade is rough, so there are many scratches on the blade.
I use a flat chisel to remove those scratches.
The flat chisel is a little harder than the diamond chisel, so it is possible to fix it.
Since the blade is attached to the chisel, you don't have to sharpen it so much.
Sharpen with a flat chisel as well.
This is the same as in 1000 and 800.
It is very important that the surface is flat, so I will fix it.
This chisel is a natural chisel, but I bought it in Kyoto.
It is a little hard chisel, so it is difficult to sharpen.
Therefore, I use a chisel called Nagura to rub the surface and sharpen it.
The amount of water should be enough to prevent it from drying.
This is a chisel for sharpening the back of the blade.
This is also a chisel that can be sharpened and distorted, so I use it appropriately.
This chisel can be sold in this state, or you can cut a natural chisel that you bought normally and use it.
Use a chisel for sharpening the back of the blade.
After sharpening the back of the blade, sharpen the front of the blade.
When it comes to the stage of sharpening the back of the blade, it is more important to sharpen the back of the blade than the surface, so the number of times to sharpen will decrease little by little.
Even in the finishing stage, sharpen the back of the blade with the feeling that it is close to the center.
When sharpening the back of the blade, sharpen it straight so that it does not become slanted.
When sharpening the back of the blade, sharpen it three times on the front, three times on the back, and three times on the front.
If there is still sharpening left, sharpen it a little bit.
Make sure that the sharpening is not clean, and sharpen it while looking at the front and back of the blade.
This completes the sharpening of the whole blade.
