Well.. It's In At Least! // 2UZ V8 1974 Celica

ThrottleStream
1 follower
1 Video View·Jul 19, 2024
Quality Car Builds Don't happen Overnight!
Support This Channel❤️
⭐️Merch: https://shop.sarahntuned.com
Patreon: https://www.patreon.com/sarahntuned
Amazon Store: https://www.amazon.com/shop/sarah-n-tuned
Website: https://www.sarahntuned.com
Instagram: sarahntuned
Facebook: sarahntuned
X/Twitter: sarahntuned
Special Thanks to my Patreon Support!
Britt F.
Chad B.
Col. L.
Curtis S.
Daniel F.
Darren M.
Dave
David L.
Jeffrey P.
Josh H.
Kevin C.
Mark L.
Meghan "in Seattle"
Nenad R.
Ray I.
Terry S.
Todd C.
hello fellow peoples watching videos
about cars on the other side of a screen
welcome to this my 1974 ra21 Toyota Cela
ST which will soon be powered by the
engine from my dad's old Toyota Tundra
if you're new and you'd like to get
caught up on why ham sandwiches don't
taste as good underwater up above my
head is uh my MR2 which is also code for
a link to the last video where I worked
on it today's Mission includes the
following steps I laid out here on my
maintenance board two of you in the past
video picked up on the fact that I
measured the routing of this custom belt
incorrectly so it has to go up around
this guy then Loop down to the
alternator if this is right right off
the first try I'm going to be so happy
in case you're new the reason why it's a
custom belt is the fact that I deleted
the AC compressor which all to U engines
came with yeah I got a Billet pulley set
for this thing sorry the Billet that's
the Billet that's Billet I'm got to hold
that oh I don't have a socket like that
see if I can hold it still with the belt
aha it worked 110 Newt
M there you go ouch that's worse than
kneeling in Legos kneeling in fresh
bolts so I had measured just over 1540
mm I went down to a 1535 I just bought a
cheap quality belt for this testing
purposes if this actually fits I'm going
to order a high grade better quality one
yeah so that's maxed out tensioner right
there and then when it's tight ah it's
got a little bit more inflection than
I'd like so like I previously mentioned
you can see that's correctly routed now
around the alternator a 1530 or 1525
will be perfect just in case you're not
tracking the 6pk represents six rib belt
and 1535 is 1535 mm of length this guy
transition antenna is oh I need
that Dusty this has got some good
brackets and Hardware on it so I'm going
to take
[Music]
it I just hauled this out of the storage
unit I'm going to be amazed if that tube
would work I mean it's a pretty ugly
intake tube but at least I can use it
for
Dimensions I knew I didn't throw it away
this stuff was way more organized when I
started but cuz I'm running out of Parts
they're kind of ending up everywhere
don't worry about what's holding that P
on right now just know that it was good
enough to measure 39 newm and the other
one is 54 okay this is critical because
this is on a bearing and you definitely
don't want to get the torque wrong on
this or else you're going to just wear
out that bearing or it's going to be
loose yep that's good one down that many
left to go I want my stuff matchy matchy
keep all my wire colors the same which
makes electrical troubleshooting very
simple so I I got a green right here I
got a red with
blue I can make it all the same color
why do this thing weigh 10 million
lb oh jeez yay my favorite part crawling
under a dash I need 5 volt reference
circuit and I need a ground from the ECU
this should be plenty it'll look a lot
cleaner by the plug too rather than just
having a little Loop go from ground to
ground and 5 Vol to 5 volt having just
individual ones running all the way back
to the main source my hands are sweaty
and
disgusting oh this smells like uncooked
macaroni noodles with little robot butt
plugs on they like it kinky too if
you're ordering a kit to do a plug like
this order double as many terminals as
you think you're going to need give
these all a test pull I was really
hoping denzo did the right thing and
labeled the number for the terminal
inside here now this doesn't have the
numbers printed on it but generally you
read it from the plug face left to right
so it be 1 2 3 4 5 6 so here's my
schematic for a Lexus LS430 accelerator
position sensor my ep2 and ep1 those are
the grounds so one and three so one and
three are my ground now my vcp1 and vcp2
those are the 5vt references and then
four and six are my 5vt reference
circuit vpa 1 VP pa2 those are the
actual signals from the ECU these are
two analog voltage circuits yellow green
white and red that's five and
six white and
red now I got to try to soer all the way
up inside
here actually those came out pretty good
for how tight that was mission complete
there's physically a throttle pedal
hooked up to the engine and ECU now
[Music]
now it's the second day in this video I
got a major job
ahead why don't gyms incorporate this
this is an excellent arm
workout this is going to majorly suck
these little guide pins are a nightmare
because even just on the bell housing by
itself it doesn't want to slide over
these very easily
ah there was a couple little burs in
here that's why it was a pain the whole
purpose of these guide doel pins is just
to help align the transmission during
installation
9.75 and kind of keeps it in place as
well 9.9 no wonder it didn't fit I want
this to be nice and smooth I don't want
it to be a struggle when I have a 100 lb
transmission above my
head that's 10 mil right there this guy
is 9.9 I know some people have been fine
with just ramming it or using a pry bar
or Hammer but why when you can make it
precise shifter case Celica but
first little bit de
[Music]
Greaser make sure the surface is clean
yes
get this stupid
thing 20 minutes later I did a couple
times that's good nice and fresh I can't
put dirty Hardware on here even if no
one's going to see it
ever Lube this
up got to be able to get this thing
through the floor so the shifter has to
come
out stuff that keep dirt out I really
don't trust this Jack this thing's so
old and janky but I don't have one of my
own so I had to borrow one
[Music]
no safety disclaimer for those of you
that are not safe be safe I don't know
how I don't know how I'm going to do
this I might literally have to bolt the
engine to the transmission and raise
it
ouch that's as far as I'm able to tip
the engine back it's such tight
tolerances that literally these lines
are the difference between getting this
thing past and up in there and not
without hacking this car car into an
absolute show I can't massage the
firewall anymore because my gas pedal
mounts right here and my pedal box goes
all the way to the very last tip on the
other side and right above this area is
the actual heater core itself and the
plastic parts of the dashboard that I
would have to destroy the interior of
this car to make more clearance there
the easiest fix would just be to cut the
hard lines back for the fuel feed and
return and then just put a union where I
can connect an and end fitting right
there so that way when I install and
remove the transmission I just
disconnect those fuel lines drip them
out of the way and easy as
that although I had this assembled once
before I have never had it fully
assembled with all the autra mons
attached at the same time so it's a bit
of a learning
experience that's what's different also
I didn't have this on last
time yeah I'm pretty sure I can drop it
down a couple inches and not worry about
anything I want to elevate my subframe
so it's not resting on the oil pan
actually this should bring it about the
same height it's situations like this
where I look forward to having a robotic
personal assistant one day let's try not
to break
[Music]
anything I want it that way so I have
these super long bolts right here where
the 886 subframe connects to the TA
chassis and that allows for me to drop
the subframe without having to fully
disconnect it I can't lower it all the
way cuz I don't think the valve covers
clear the frame rails if they do it's by
literally a millimeter per side if I
disconnect the lower control arm from
the subframe and I should allow more
range of motion I didn't think I was
going to have to drop it that much but
[Music]
I didn't really give me the clearance I
was expecting it to uh do I have enough
room
I don't know how to push and lift
at the same time I don't have five arms
[Music]
maybe can't tell if the input shaft is
in it's like robot sex there I go as low
as I
can oh man it's like literally almost
there that's as far up as I can go
though oh
wait no way I think I got it to start
face I got
it reposition the camera here so uh you
can see all these upper bolts are not
fun I'm sorry for the lack of camera
angles I can't do two things at once
here thankfully the two upper bolts on
the top of the transmission are
accessible like many other transmissions
when you remove them with an array of
Ratchet extensions I don't know why is
this so much more difficult this time
around because I've had this all up in
there a couple times that's what he said
to test fit and it fit this is just the
first start I'm not trying to drive the
car so I don't need to have every one of
the bolts in there I'm going to have my
10 and two bolts missing yeah it's just
the one by the throttle pedal I can't
get to but I think I can get to it from
the
side engine go back up
[Music]
that's supported now I had a feeling
this might be an issue and this is why I
use the w58 this is as close as I could
get to the original hole for the shifter
and I'm off by about an inch or so that
means I got to modify the opening this
is why I waited to paint the engine bay
because even though I had this all test
fit once it's not the same as test
fitting it when it actually goes to
start and
run I'm mildly dizzy I don't know why
okay
face is it ideal that I have to drop the
subframe some to get the transmission in
and out no is it unheard of no there are
some cars from the factory you have to
do that and it's really not that hard
it's only four bolts
so so fourth day on this video my goal
for the end of this video is to have the
car ready to run and I think that that's
actually possible I forgot how this
thing even goes got to make these a
little bit
[Music]
bigger there that'll give you some
movement hopefully enlarging these holes
just a millimeter or so will make the
alignment a little bit easier cuz before
this was a nightmare yeah like right
there the real question is going to be
whether or not I can get the steering
rack back in didn't think about that one
I really hope that I didn't screw up by
not putting this in before I lowered
that
down cuz the clearance is like
nil maybe without the bushing as I sit
here struggling with this I knew fully
what I had to do I was just in denial of
it I got to lower the
steer why the only way to get the
steering rack in there is to lower the
subframe enough to clear it so I need to
keep the engine
up
almost in theory if I just undo these
two engine mount bolts and support the
engine then I can lower the subframe
just like a couple millimeters and I can
slide that steering rack in I think what
is holding you in just come out
almost more almost that's both motor
mount bolts out almost there we go
yeah I'm going to have to modify this a
little
[Music]
bit that just gained me a ton more
clearance now that I know the correct
order of removal and assembly it should
be much easier the next time around
after I paint the engine
[Music]
[Applause]
bay I don't know how this is possible
because when I was sticking the
transmission in this car it seemed like
nothing was going to fit everything was
out of whack it was rubbing in all kinds
of places but now that everything is
tightened down there's clearance
everywhere there is supposed to be
clearance nothing looks like it's going
to rub or vibrate and it all fits you
can see up above the steering rack
there's about 3 or 4 mm between the oil
pan and the bushing there's actually
ample room up here where the fuel lines
are at there's miles of clearance over
here on the side of the transmission by
the tunnel there has to be some luck in
there cuz I suck at math now it's time
to see where the transmission came out
somewhere yep that kind of sucks I
wasn't intending on this self
clearancing itself but I'm not sad that
it did there hey look at that it's
barely off the rubber boot is a little
uh I got to admit that is pretty damn
close considering this thing has a
Tundra V8 and a Toyota Supra
transmission shoved into it for it to
almost line up perfectly man I'm out of
blades for my little finger saw thing so
these little robot utters right here are
for my oil cooler and oil filter I don't
need the oil cooler for first start but
I do need the oil filter I don't have a
ton of room to work with in this area
there are many combinations in which I
can do this but there's only one where
it will actually
work wow that drastically took up space
more than I thought it would I don't
know about this unless I just bount it
upside down kind of like a Subaru and
put it like right here I had these two
EMP 10 threaded holes for where I think
the voltage regulator used to go there
before so I can make a bracket for this
to sit and if it sits at this form of an
angle you can see right there so the oil
will come out of the filter and then
cycle back down to the engine so it'll
empty your filter out that way you don't
make a mess I know I said there is a
possibility I might be able to start the
car in this video but I think anyone
watching right now that isn't smooth
brained understands the complexity of
the task at hand and the fact that I'm
doing this 100% by myself on top of
filming and editing these videos and all
the other crap I have to do to manage
this whole operation so thankfully
though for the next video all I really
have left is fluid related stuff oil oil
cooler transmission fluid and fix a
couple fuel lines and then there's more
things that lots more that I have to
do um okay thank you guys for watching
I'll see you soon with another video bye
if you would like to support what you
see here
uh you can take one of these guys home
link on my website below
