WE REMOVED THE BRAKE DRUMS, THE SHAFTS WERE OUT AND HAD TO GRIND OF THE BEARINGS ON THE BOAT CAR
After breaking down last week, this week we have been full on busy stripping down the brake system of the boat car. After removing the wheels, brakes, brake drums, shafts and grinding of the bearings, we had to locate all the parts, this was a task in itself, because at the moment there is a shortage of car parts in the UK. After literally tearing our hair our, calling about hundred motor parts suppliers and surfing the internet for over 200 hours, we finally located what we needed. However, the parts are yet to come, so fingers crossed we will have them this week and refitted to hit the road/ waterways next week.
Thank you so much for joining us this week and don't forget to hit the SUBSCRIBE button and leave a like.
Thanks to Epidemic Sounds for a great selection of song
That's Mari. That's Vanessa. That's Ava. That's me. And that's Chris.
We're the family, traveling a million miles in our boat car. We hope you enjoy our journey.
Hey guys. Ni hao ma. What is it with you and this language thing?
I don't know. I'm getting ready to go traveling I suppose.
Right, so you saw yesterday, well it was actually a couple of days now,
we had to take, I think, a couple of days just to get over the trauma of that journey.
And the journey was just, I think, the most traumatic we've had, right?
Yeah.
We had to call out the breakdown service twice.
Twice.
We got told in the end. And then obviously we're going to start stripping it down.
Yeah. So that's going to be interesting.
And seeing what's wrong with it.
Yeah. So what is it going to be doing to it?
Setting the light.
I'm joking.
I'm going to strip it all down and take the wheels off, take the drums off.
And my guess is, I think the wheel bearing has seized up.
Right.
I've also got a brake problem I need to look at.
Yeah. Which you've had for a little while.
A little while. But before we fixed it, I had it fixed and it's happened again.
So I've got to get that done. So we're going to order some new parts, aren't we?
So what are you going to be ordering?
Probably brake pads. I've got a suspicion one wheel bearing's gone, but we'll do two.
And if it's associated with the braking system.
Yeah.
Because I don't know yet until I take it apart.
Oh my God. And probably do the diff oil at the same time?
Yeah, I've got to do that. I've got to drain the diff oil.
Right.
And make sure that's new.
I think what I'll do is just leave you to it, right?
No.
Get out of the way.
You need to help.
Oh my God.
Obviously last time I had issues with the car, Elaine helped.
But this time it involves grease. It's not going to happen.
No.
This is the oil remover, sump remover tool, multi-tool.
And I've already pre-done it. I'm just going to loosen it off a bit more.
Get this underneath.
And if you haven't got an oil pan, just get a five litre bottle and cut it in half.
No need to spend loads of money getting an oil drain pan if you don't need one.
Let's see what happens. See what colour this is.
Yep.
That's definitely water. Look at that.
Can you put seals on that though?
I did, but I'll be honest with you, I was a bit lazy.
I didn't change the seals properly.
So that is no good. That is water, look.
I'm glad it drained for a while, so it's all come out of there.
So Chris got straight to work.
First, he removed the wheels.
Then he removed the wheel hubs.
All right, guys.
Right, I'm back underneath the car.
I've managed to strip this out.
As you can see, it is a complete state.
So while this is off, I'm going to take the opportunity to clean all this up.
Probably paint it, protect it from the salt.
But already, that does not look good.
Anyway, so I've removed the brake drum from the back.
There's disc brakes on the front and also a drum on the rear.
So I'll use these bolts here.
I'm not sure if these bolts are the same in every car,
but I'll use the bolts to push the drum off.
It's hard doing this with one hand and holding the camera as well.
There you go.
Come back around.
I've been having a bit of handbrake problems with this for a while,
so I'm going to take the opportunity to make a few modifications while I've got this off.
That is tight on there, guys.
This just came out of there.
Right, that just came out of my brake drum.
So yeah, that's the retaining pin for the brake shoes.
That explains why that isn't working.
Can I just show you?
Took all the bits out of the brakes.
Took all of this out and what I notice is this is broken.
That is supposed to be straight
and this bit here should be the same length as this part here.
It's completely broken off.
So I need a new one of them.
Everything else in here looks okay.
The main problem is this thing here, the bearing.
But while we're doing the other one, I might as well do them both together
because this one had a brake problem anyway on this side.
Right, okay.
So I'm going to continue to take all this off.
I've got to take the handbrake cable out from the back
and then I'm going to take, pull this out.
And what I normally do is pull this out
and then bolt the wheels up with a couple of bolts,
put the wheel on and then slide the wheel off with the whole shaft in it.
Everything should come out at the same time.
I've got the bolt cast stripped down after the little events with breaking down
and it wasn't very good.
Bits of the wheel bearing and seal everywhere.
It's a bit dark at the moment, I keep working in the dark
but bits of debris in there and there's still, I can't see very well,
there's still little bits you can probably see the rub
which I need to clean out in there.
So I've stripped it all down.
It does need some work.
I mean some of these bushes look like they're past it now.
Generally in good condition but yeah this is the problem.
The wheel bearing sits in there completely, yeah it's completely gone
and I think the seal gave way and let a lot of water in.
I'm at the stages now with these wheel hops.
I've taken that, I've taken them off the vehicle
and I'm just putting some some coating on there
to protect it from the salt water as the grain water
and I'm using tetra seal.
Okay something you don't classic cars underneath.
This car's not fully submerged in the water all the time.
It's only when I go in the water so this would be more enough
where if it was constantly in the water I use something like anti-foul
or something like that which you'd have to paint on every single year.
It could be an option in the future, I don't know.
Try my hardest to, what I've got to do, I've got to cut this off
and completely grind this off.
So I'm going to try and find my grinder, cut this off, get this bearing off,
get some new ones ordered because I haven't ordered them yet
and then I just wanted to see how bad it was.
But apart from that everything looks okay.
But I would say I've got an opportunity at the moment while this is out
to probably put a flushing kit into this back plate.
So basically when I go or collect the water especially the sea
I can then put a nose pipe on and flush water through the brake system
to stop it seizing up because that's a problem I've been having.
All right so I'm going to get back to what I was doing.
Carry on taking this out but as you can see completely gone
and I'm sure the other side's going to be the same.
That's what's left of the back plate of the bearing.
Seal, whatever you want to call it, it's completely gone.
There's no rubber left in there at all.
I believe that's it.
I'll take this bearing out and it doesn't come off very easily
and I believe that's the retaining ring.
If I can take this off gently I can probably use it
just in case I don't get another one.
It's the one you don't get with a kit.
So I'll take that off.
That's off.
I can probably use that one and put it back on.
So guys that's it.
I've got this bearing off and just talking to myself there.
And now we need to try and get these parts.
Bearing, spacer and we've got this flange here which it sits on.
So I don't want to lose that because this is the bit apparently you don't get with
kits and some people cut them off and unfortunately I've damaged that one.
But yeah.
Can you get it with the other one?
I think you can.
I think it does come in three parts if I remember rightly.
Yeah it's hard to get them off without cutting it.
What about the other one?
Did you cut the other one?
No.
No but I think it does come with all the bits anyway.
Comes with the kit.
Right guys I'm going to go and see where Chris has got to with this car
because we must get out ASAP.
Go find him.
I had to see just how far Chris has got with getting the parts changed
because we needed to get this car back on the road.
I've got one problem.
What?
And I bet you're thinking this anyway.
What?
I've taken all the springs out of the brake pads.
And you don't know how it goes back in there?
Really the problem is I took this out and I stripped it all down
and there's lots of springs everywhere.
I know.
And someone told me, a very wise man told me before this was a mechanic
who said make sure I take a picture of everything before I strip it down.
I was so eager to get this off and I've just got a load of brings and springs.
Brings?
Springs.
And loads of stuff here.
Brake pad.
I know what they are.
I just don't know where all of them go.
A few of the things I do but I didn't realise that rear drape drums can be so complicated.
I've never done drape drums before.
I've always done calipers.
Brake drums.
You said drape drums.
Yeah I've always done calipers.
Yeah.
And who told me there'd be a lot of springs and stuff coming out of it?
And it took me ages to get out as well
but I didn't make a mental note of which one they came out of.
Not happy.
Anyway.
That's another story.
That's going to be another bit of content for you guys.
You're making an adjustment aren't you?
Adjustment?
Yeah so a modification.
I won't make an adjustment on finding springs.
I know I don't see that.
That's an adjustment.
Right yeah so what it is.
I used to have a boat trailer and I'll say we used to have a boat trailer
and we used to have a flushing kit so when we come out the water
we can flush the brakes out and that hopefully especially salt water
helps keep things all nice.
Get salt out of there before we get back on the road.
Unfortunately this vehicle was never made with that
and it's something which really worries me.
When you go a long distance like we do away from our base
then we think well we'll flush the water.
How do we get the brakes clean?
So research has been shown and it's actually proven
if you flush the system out as much as you can
it will lengthen the life of your braking system
which means there won't be as much corrosion or seized up parts
because you're putting fresh water for it
almost immediately after you come out the water.
So I've decided, I should really decided to work out where these springs go
but I've decided to create a flush system myself.
So I bought some nozzles there
and I'm going to basically drill a hole within the plate
and then the nozzle come out which the hose pipe will attach to the back
and then I'll be able to put a hose pipe connector onto a main inlet
and flush both wheels out at the same time.
That's the plan anyway, that's what I'm hoping will happen.
In the meantime I've cleaned all this up
I've put some car underbody paint on here
because it's not going to be submerged in the water permanently
it's going to be in and out
we'll go for a drive or cruise
we'll come out at some point at the end of the day
so I'm not going to use anti-foul and stuff
because that's continuous painting and stuff
so I'm just going to give it some general underbody protection.
It's worked really well since we've had it
so there's not hardly barely any rust underneath there
which I'm very surprised with the amount of water
attached to it during this
so that's clearly working
and I'm going to put that in there
so it will basically be inside
not actually
that bit will be sticking out through the bottom
and then water will spout
hold on I'll show you
water will spout through here
and both sides and flush the water and the system out
cool
that's what's supposed to happen
well first let's um try and find these springs eh?
well yeah a few of them are missing
if not I'm gonna have to order a new set
oh don't say that
I'm hoping they come with instructions
they probably don't
um they'll come with a bag of springs
but if not I'm gonna have to go online
and see how everyone else does it
right it's daytime for once
because I've been filming the night time
trying to get this work done
and um that is what I've done
it doesn't look much
I've fitted two jet wash nozzles
I'll say
I'll call them that for now
which are near the brake server
which is that
this bit is whilst you press the brake
that opens it outwards
and pushes the brake pads out
and I've put a connector on there
which I'll put pipes
which I'll do another video
and show you how I'm going to connect these up
so basically this will be
where the water comes through
to flush the brake system out
which will be inside like that
okay so um that's one modification
I or we decided to do
when the car came off the road
because I need to do it anyway
and um I'm just doing this one now
I've cut the holes out
and that's I'm gonna start
obviously sealing these bits of rusty bits up
and then I'll connect that up as well
that's gonna be the other one done
but clearly that's gonna be on the back
and so what else we're waiting for
wait for wheel bearings
we're still waiting on the brake adjusters
we need to get this car back on the road
so with any luck
the parts will arrive tomorrow
and we'll see you back on the road
or the water next week
thank you so much for watching