The Unorthodox Method that Holds My Cake Stand Together

Artistic ceramics
10 followers
1 Video View·Nov 13, 2026
AI Generated·May contain errors
I love making cake stands
but the process has been feeling a little like a recipe that
I haven't quite refined.
However I've been experimenting with an unorthodox method.
Have I finally mastered the cake plate?
I'm using 1.5 kilos for the cake plate
and I'll need another half a kilo for the stand.
I start by making the plate and I centre.
I'm using a fine earthenware clay.
I want to fire my piece at quite a low temperature
to give my pieces a better chance of staying flat.
So why are cake stands so tricky? Well you have a
large area of plate sitting atop a small stand
with very little support. This makes the plate
prone to warping, slumping and cracking.
Once I've centered the clay I flatten the clay.
To just a little under the diameter of the plate.
I've tried some different ways of making cake
stands and I've found that I've had the least misshaping
by making my cake stand in one piece
but this always hasn't been the most aesthetically pleasing
and I'm hoping to remedy this. Once I
flatten the clay I open out just a little enough to form a rim
and I compress the clay.
First outwards and then back inwards.
This really does help prevent flatware from cracking.
I pull up the rim. Nearly all my one piece cake plates had a flat top.
After all what you put on
the plate can just slide right off.
So this method allows me to make a proper plate with a generous
rim. I trim around the foot and then I wire through
and set aside to dry to leather hard.
Now for the stand. I take half a kilo of clay and I center.
I have found that making the stand
separately gives me a lighter and more elegant stand
but I've also encountered warping when I
join the stand to the plate.
Sometimes it doesn't emerge till the final firing
and a cake stand on a lean is not a very useful cake stand.
So once I've centered the clay I
I flatten the top.
Then I can push down into the clay
And I can open up and pull up the walls.
I pull up the walls
to the final height.
So I'm hoping this method makes the leany problem a thing of the past.
And then I can start to shape the stand.
I bring the rim, which will be the foot of the cake stand,
out into a curve.
I'm going to make sure that that rim is flat.
And I make sure to leave that rim a bit chunky and rounded.
I trim around the base and then I wire through
and set aside to dry to leather
hard. It's time to trim.
I'm happy with the shape of the stand so I just make
sure that the surface is smooth but I do need to trim the plate.
I use some pieces
of cork to support the plate while trimming.
These are actually cork pot
holders that I can stack to get the right height.
They're soft but firm and don't leave marks on the inside of the plate.
While I trim be sure that you're subscribed to our channel so you don't
miss any of our experiments and projects and of course like and
comment below. It's much appreciated. So I trim across
the surface of the plate and around the
outer edge. I just want to create a gentle
rounded profile and then I just smooth the surface.
I use a flexible rib.
Up until now it's pretty standard for two pieces
that get joined together but as I mentioned
I'm not going to join these pieces together.
I'm going to bisque fire them separately
but I do want to cut an indent in the plate that
will fit with the base.
So after marking out a measurement for the base I trim into the plate.
It only needs to be maybe five mil deep.
So as I've mentioned I'm not going to join these two parts together
but I will end up with a single
cake stand. What I'm hoping to do is allow
the glaze to fuse these two pieces together so the
indent for the base is really to make sure
that the plate doesn't slide around as the glaze melts.
It will make sure that the plate stays right
on top of the stand and after checking for fit,
I set aside
to dry fully before bisque firing.
Then it's time to glaze.
I'll glaze the plate in
a wide basin but the stand I just dip
into my bucket of turquoise glaze.
Once dry I can wipe the foot.
I really want to get an even coat of glaze on both pieces
and now I can glaze the plate.
I start by pouring my glaze into a wide basin
and then I dip my plate. I use tongs
and I allow the glaze to run off the plate.
I wait till it's dry to set it down. Now I
take the base and carefully set it on the plate
and then I set it on a kiln shelf.
I'll load it into the kiln on the shelf
and then I fire to an earthenware temperature.
The glaze has fused the two pieces together fully
and there's no warping, cracking or slumping.
The pieces fit together really well.
So here's some key points when making this project.
Stick with an earthenware firing. Make sure the height of the stand
is even. Support your plate when trimming it so it doesn't miss shape.
Make sure that the top of your stand
and the indent in your plate are both flat.
Make sure you get an even coat of glaze on both pieces.
And make sure that the plate doesn't move
when you're loading into your kiln.
For more cake plate functionality, check out my cake plate with a lid.
And happy potting!
