The TRUTH About Boost Leaks: Find Out How Much HP You're REALLY Losing! (Suprising Results!)
May 16, 2024
We all know boost leaks are bad and can wreak havoc on any forced induction system, but at what point will you start to see a measurable power loss. In Todays video we answer an age old question, what happens when you have a boost leak in your charge system? We tested it and the results were so interesting!
hey guys in today's video we are
answering an age-old question what
happens when you have Boost leaks in
your charge system and where exactly do
you start to see the power lost we
tested it so you don't have to
[Music]
[Music]
[Music]
now for today's video we have a Toyota
2JZ mounted on here you might have seen
this exact setup before when we did the
6870 comparison video the only change
now is that we have the Precision 6670
turbocharger and the Boost is being
controlled through these two tile
wastegates now Wilson over here is
having a pretty good day little smiley
face we're going to have him turn into
this guy right here with a frowny face
and we'll be doing gradually larger
holes throughout each run uh we should
be starting around an eighth of an inch
and hopefully go all the way up to about
an inch of a hole and I think that we're
going to see a big change somewhere
around half an inch but I want you guys
to let us know in the comment section
below what your guess will be obviously
it's going to make less power at some
point or we might see the turbocharger
speed start to increase dramatically to
try try to keep that exact same boost
Target of 15 psi so without further Ado
let's go ahead and do a baseline run of
15 psi see what this engine makes see
what the turbo shaft speed is like and
um see what we start working with let's
check it out
[Applause]
[Music]
[Music]
[Applause]
that was pretty on the money so we were
targeting 15 lbs of boost you can see
across the whole RPM range it's on that
15 lb Target and if we look a little
closer in the ECU software the log for
that pass the turbo speed was at 86
[Music]
that we're comparing everything to these
numbers right there so how much power
was that right there Brian let's take a
look okay so Peak power of 694
horsepower and
465 lbs of torque so once again more
Baseline numbers let's go ahead and
start doing the first control leak and
uh let's rip out the drill see what we
can do to the poral Wilson on that
charge pipe
[Music]
all right so Wilson's going from a
closed mouth smile to an openmouth smile
because he likes to show his teeth
unfortunately for Wilson he doesn't
really go to the dentist often so he's
got a little cavity and that cavity is
about to be poked out dentist Brian
Fields pull the whole tooth out so this
right here we're starting with an eighth
of an inch right roughly yep little
cavity this will also bece educational
video for children kids don't want to go
to the dentist are you ready to go to
Disneyland
yeah make sure to go to the dentist
[Music]
kids it's like if you're purging nitrous
[Music]
okay so this is like we said our first
controlled leak test um before anything
we have to get back up to operating
temperature we always Target the exact
same oil temperature the density
altitude everything is monitored through
our superflow engine Dyno and it's the
data that we've collected and shown in
previous videos like the 6870 versus
test all of that stuff can be combed
through and make sure that we have no
variable or as least variables as
possible to make sure our actual test is
reflecting true data so right now 8 in
hole is what we're working with right
Brian what do you think's going to
happen with it I don't think anything's
going to make a differ no change okay I
think if anything we might see a little
more turbo speed but I feel like it's
still going to make the same amount of
boost and very very similar power
[Music]
[Applause]
man that's really close so the red line
is the new run the blue one is the first
run it switches over the newest run
turns red how much power is there any
power difference in there Brian let's
take a
look so very very close shaft speed uh
we're looking at
86,500 so that's slightly more than our
last run I believe it was 86,2 so that's
pretty close the turbocharger speed was
very very close to the previous run uh
within a couple hundred RPM and the
Boost itself was right on the money
Brian what do you think yeah that didn't
make much difference let's go up to a
quarter inch hole let's make the hole
[Music]
bigger the
off ASMR
definitely go to the
dentist so once again we're going back
through the warm-up procedure getting it
to that same operating temperature I
think we'll start to see a little bit
more of a change here Ryan not much
we'll see I think half in will notice a
big difference once it's big enough for
you to stick a finger in it I think it's
going to really really start affecting
power just so you guys are a little more
familiar with our engine Dyno on the
right hand side we have a table that
uses a fuel cell we have a level sensor
on the side of it we run one ethanol R
which is the fuel for all of our tests
here and it's um a very nice consistent
fuel we just enjoy using something
that's easy to grab off the shelf and
put it in the engine have no questions
of if it'll run right cuz we know that
it's already set up for that but
everything else should be good we're
almost at operating temperature we're
getting ready to do the second or
actually third run this one with a/ Quin
hole rather than an e/ in hole I still
think that's going to be very very
similar I don't think we're going to see
much power loss at all if any and uh
maybe turbo speed continues to go up to
try to compensate for that but I don't
know I think it's pretty good what do
you think I think once we get to that/
inch Mark we'll see some change right
once it's a lot bigger so without
further Ado we're a few degrees off
let's kick it and do a pull
[Music]
okay so once again like we mentioned
before the the latest run is that red
line right there
so looks like it's making more back
pressure that's an interesting point
right there um the Boost looks very very
similar to the other ones but the back
pressure really stands out I can't
believe that it's that much higher so
yeah so here's our power from all three
pools you can see there are all very
very similar right there so not a whole
lot of change and Power band or Peak
power um they're all very very close to
each other let's see the back pressure
is the thing that stood out to me the
most more back pressure with this latest
pool looking at the daph now you'll
notice that there is an increase of back
pressure versus the Boost staying very
similar if not a little bit lower than
the initial test why exactly is it doing
that the turbo is now having to do more
work to achieve the same or similar
boost and the turbine speed is
increasing that's going to create more
back pressure and it's not going to
create more boost since obviously we
have a big hole in the charge
[Music]
P I think you're only holding 4 lbs
right now that's it yeah what now you're
at
five let's just hold it let it fill up a
little now you're at eight it it'll pop
really good
now
ready wa
[Music]
let's see red line being the most recent
once it updates back pressure up and
boost down oh yeah proof is in the
pudding all right let's check out this
turbo speed 88,000 okay so 88,500 let's
see the
power oh it's way down look at that oh
wow so these are the previous runs
overlaid our control then our two
controlled leaks and now this is our
third leak half an inch you can
definitely see a decline in power and
torque across the whole Power Band and
looks like for Boost we lost what about
a pound pound and a half yeah if not
more that's that that last one right
there half about yeah so that's pretty
substantial and the back pressure is way
up right there compared to before that's
a perfect indication of why you want to
monitor these things at the racetrack
you want to be able to check things like
your back pressure your turbo speed and
if you're racing a car that doesn't have
a lot of changes often you can look at
these two numbers uh well actually three
the the Boost the back pressure and the
turbo speed to have a control for your
normal race environment once you start
to see some change there maybe you're
down some M an hour you're trying to
figure out what's going on having these
tools and having the ability to look at
this data is so important in any race
program so that's awesome let's go
bigger on this hole let's see what it
does with what's next a full inch um
let's do 3/4 3/4 inch okay yeah let's go
for that and then um hopefully we see a
huge change but uh right off the bat
it's it's looking real promising for
data for sure this is fun I think a good
comparison is the quarter in hole would
be equivalent to like a blowoff valve
vacuum hose coming off and a half-in
hole would be equivalent to like a brake
booster hose coming off so that's a cool
test what do you think uh 3/4 in hole is
going to be equivalent to uh your idle
air control motor falling that's a good
comparison all right okay let's go ahead
and drill that bad boy
[Applause]
out I'm interested to see there's a
visual representation very scientific
method right here that we can see of
this boost
[Applause]
[Music]
leak 13 and change
13 we're were up on back pressure there
wonder by how much
whoa okay so 21 almost 21 and 12 PBS of
back
pressure down on
[Music]
Boost so that's pretty significant right
there yeah and see those two numbers
just continue to drift apart from
everything else so let's see the she the
speed oh man we hit 90,000 on the
turbocharger speed so that's up from the
original
86,2 I believe was the Baseline run and
and 90,000 that's it's just getting
bigger and bigger it's going faster and
faster power L is
yeah oh wow where's that
roughly where are we at in it's about 50
horsepower from our Baseline yeah that's
a good amount of power loss but it took
that large of a hole to actually show up
I mean those first three runs were so
close together that once you get up to
that
half inch 3/4 inch is when it really
starts to shine so just like you were
saying a a a brake booster line or a
couple vacuum lines all together really
does do an effect that's interesting
what's super cool though is the the
shaft speed that's interesting to see it
keep on growing and growing so the
computer is doing its best to try to
still make that 15 lb of boost Target
but there's only so much that it's
allowed to do and so much that it can do
so it's very interesting I think we up
it one more and try to go for the full
inure sure let's do the full inure let's
do
[Music]
it oh Wilson
now I think this should be our final
pool for terms of getting the width of
the hole bigger yep I predict that in
this case we're going to see not only
about 50 horsepower loss like we did
previously but we're also going to see
the back pressure go way up trying to do
its thing but turbo speed will go up
continue to go up I mean we've seen that
it's kind of a trend at this point
definitely don't do this at home if
you're trying to make Power don't drill
holes in your intake cuz this will
happen y inefficient
[Music]
[Applause]
way down on power
there look at that that is a crazy
difference I mean that's what we
expected obviously it's going to
continue to drop more and more power
that's just over 550 so like 570 is
right there when when we started it was
nearly 700 so that's a a huge spread
right there uh turbo speed got up to
93,471 so the turbo's definitely working
overtime trying to make it happen back
pressure 24 lb of back pressure and the
Boost was what 13 almost 13 125 yeah
about
12 through the so literally double the
back pressure to try to still
[Music]
survive at that so wow that's
uh that sucks that does suck it's not a
good day the back pressure is double of
what we started from on our Baseline so
yeah so this is our first graph uh which
is our Mainline graph you can see it
crossed over and on our newest pole our
back pressure was always above our boost
which is really cool to see right yeah
and never never overlapped yeah so
typically on a car that's running well
you'll see that somewhere in the higher
RPMs right you'll you'll have the brake
the the back pressure overcome the the
Boost whereas right here it never even
got to that point so that's that's
definitely interesting to see good uh
good eye on pointing that out it's very
cool so for that last pool we only made
about 12 PSI so what we're doing now we
want to have the computer adjust the
Boost settings so that we're able to hit
that 15 psi Target um we did some
adjustments here I think that this
should achieve that obviously it's still
going to have more back pressure it's
it's still going to run the turbo harder
but let's see exactly by how much so
let's hope that this one hits 15 lbs
around that Mark yep turbo shaft speed
is should really increased increase
let's check this
[Music]
[Applause]
[Music]
out wow so it looks like shaft spe got
up to
102,000 RPM which is it's pretty crazy
if you ask me like I said guys this was
us making the computer add more to be
able to try to hit that original 15 lb
Target it's going to be extremely
difficult to do that with a giant hole
in your charge pipe so you you can't ask
it to be right on the money like it was
originally but it's it's very
interesting to see just like on the
previous runs with the large hole the
back pressure is always and continuously
way above the boost
pressure and what did it make for power
right there same PSI but obviously a lot
less air wow so that's way down from
high 600s to yeah 620 is that 630 80 80
pound uh 80 horsepower difference same
PSI wow that's interesting and the back
pressure when you look it's 2 to one
compared to the Boost yeah which is
literally dou compared to before it's
not even one and a half to one right so
which on on Turbo Chargers when you're
pushing them super super hard you'll
start to see that back pressure
naturally happen with large amounts of
boost but this turbocharger wouldn't
react like that as you saw under normal
circumstances so really interesting
level yeah yeah yeah okay so now that
we're done with the testing there are a
few things that we want to actually
touch on about the information that we
were presenting and why we actually did
this test it's very obvious you don't
want holes in your charge pipe system
this is more of a what would happen
scenario so some of you guys with a very
good eye might have noticed the Run
orders are a little different towards
the beginning and the end of the test if
you go very closely to the top of the
dino graphs you'll see the Run order
number and at the very beginning the
first test that we did was 11 and then
the first controlled leak was 13 what
happened to 12 if we ever abort a run or
we don't find the data to be clean for
us to present it to you guys then we'll
just redo the run and it'll log to the
next number at the end of the test we
finished at 17 and we were trying a
whole bunch of funky stuff to try to get
that boost back to 15 which is nearly
impossible when you think about it we
have an inch diameter hole in the charge
pipe so how are you going to still try
to manipulate the ECU to make that 15
psi Target so from that 17 run we had to
do a couple things and we tried a couple
methods to finally get it to that close
15 psi Mark and we ended up doing that
at run number 21 obviously this ended up
just being a really fun video that we
can mess around with the engine Dyno a
little bit more I think being able to
approach this whole engine Dyno series
with the open mentality of I have this
opinion of how something works let's see
if it's actually true is going to give
us a lot of valuable information to be
able to provide the community with me
personally I've always thought that if
you had this hairline boost leak or if
you had a gasket that wasn't perfectly
sealed it would be this giant problem in
any system now obviously it's not a good
thing to have Boost leaks but now we
know that it's not a huge problem until
you get to that larger diameter hole
like we saw today I'm not advocating for
Boost leaks please fix your system you
don't want to show up to a Dyno
appointment and have issues but if
you're at the racetrack and you start
having little issues you don't have to
break your head over it I want to hear
what you guys would like to see us test
next on the engine Dyno there's a lot of
age-old myths that we might have heard
from Generations before us and we would
love to test more things like that
thanks for watching guys like always and
we'll see you on the next video we're
happy to do stuff like this and we can't
wait to do more
[Music]

