This Colonial Williamsburg film, which premiered in 1973, depicts a master blacksmith and his assistants in Williamsburg, Virginia, as they forge and repair the community’s tools, farm implements, and firearms. The film’s name comes from the epitaph of Williamsburg blacksmith Hugh Orr, who rose to become a prominent businessman in the city, but whose tombstone remembers him simply as a “hammer Man.” The film features master blacksmith John Allgood, who worked at the Colonial Williamsburg Foundation for more than 30 years.
Produced by Arthur L. Smith, the head of Colonial Williamsburg's audiovisual department, "The Hammerman in Williamsburg" was one of dozens of educational films produced for use in schools, museums, libraries, and television broadcasts.
The Colonial Williamsburg Foundation is a not-for-profit 501(c)3 educational institution and the largest U.S. history museum in the world.
What do we do?
Oh, this is a pretty mess.
Of all the places that a chain could break.
Perhaps we can use the broken link to mend it.
No, son.
That would only bend the other link.
I fear there's nothing for it,
but the chain must go to the blacksmith in the morning.
I'm
a
blacksmith.
I've been for 37 years.
Dave Burcham's my journeyman.
He's been with me for 10 years.
Bill's my helper.
He's been with me for four years.
Both very good workers,
and I believe we can make most any iron item that you would need.
Start something, go ahead and finish it.
That's for your own good.
If you start something, every time someone
will walk in and want something done,
if you stop, it takes you some time to get started back on it again.
So finish whatever you started, and then work for him.
Hey,
son,
what
can
I
do
for
you?
We broke our chain pulling stumps.
Pa says we have to get that field clear today.
Well, I think we can mend it for you.
I'll go fetch it.
Broken
link.
All right, we'll make you a new one. We won't use the old one,
and we'll have to open this up a little bit right here.
Bill, help
me here.
That'll
work.
I think that's
the first thing
a blacksmith has got
to learn is his heat.
Not get too hot, or not
to work it too cold.
And if you've got a lot of shaping to do,
you've got to keep the material hot.
If you don't, you're not accomplishing anything.
Now, if you've got the item almost to the shape that you want it in,
a good low heat is good for smoothing up, dressing up.
It goes out a lot better when it isn't quite so hot.
But for shaping, you gotta have a good hot temperature
there
all
the
time.
I'm
ashamed,
eh?
In forge welding, to get a good weld,
you're supposed to heat your material slowly,
so the heat will penetrate all the way through.
It's got to be just as hot inside as it is on the outside.
So you gotta have a good, clean fire,
you've got to have a flux,
you've got to have a slow rise in temperature
when
you're
welding.
After you hit this a few licks,
you done done all the welding you're gonna do.
Because it began to cool us off.
If you already got it welded, and you're just shaping it up,
you can work that till it gets cold.
There
you
are,
that's
good
as
new.
We're much obliged to you.
Yeah.
I brought some other things to be fixed,
but Posse's is no hurry about that.
I'll go fetch it.
Much
obliged.
Very much.
The secret
for twisting
a piece of iron
is to have
a uniform heat.
A piece of material that's natural
is going to twist in the hottest place.
If you've got one end of it hotter than the other piece where you want
to twist, you're going to have to start your twist, put it back
in the fire and heat it where it ain't twisting fast enough.
You can take water and pour it in a hot place a little bit
and stop that from twisting and keep on.
But it's a little bit easier if it ain't too big a piece
of material to always put back in the fire and run the heat on it.
The
most
difficult
thing
is
to
learn
how
to
use
a
hammer.
Throw in your hand, raise your hand sideways to make the blow count.
If you're drawing out a piece of material,
you can hit it flat, kind of a push and lick, you might say.
If you're spreading, you've got to come from the corners, you know,
spreading this out, and then work the center that pushes it out.
There's a lot of difference in spreading a piece
of material than it is drawing it out in length, making it width.
You've got to do this through experience.
You just can't stand and watch somebody else do it.
You've got to do it yourself.
You get the fundamentals for standing there watching,
but to get a good job, you've got to try it.
It's
a
very
useful
tool.
Especially when you're working on something
that has to have a smooth surface,
because that's used for smoothing up, finishing up.
The flatter is the biggest portion, and would have a big, wide face,
and then you're hitting it with a great big sledgehammer,
8, 10, or 12-pound sledgehammer.
It's so much faster than trying to smooth it up with a hand hammer
and does a much better job.
Making
a lap well,
when you
first
hit it,
you always
hit it in
the center,
and then you'll have a lap on both sides.
Then you run a heat, get one lap,
then you can run a heat and get the other lap.
Like that, you're trying to hide all the laps where it won't be seen.
But if you know you've got a good weld and you lap two pieces together,
you don't have to worry about the seam
on each side because it won't break.
But you don't find too many iron items that's welded together
that you don't see some kind of a little seam there,
which don't necessarily mean anything.
You can punch a hole much quicker than you can drill it.
It might not be as accurate,
but you can punch any size hole or any shape hole that you want.
If you've got a pretty good size hole, we find that you take
the coal dust and put in the hole after you want to start.
That seems to form a gas that keeps your punch from sticking
and it keeps it from getting too hot.
But if you don't do that, your punch,
the biggest majority of the time, will stick.
You're in trouble then.
A lot of times you may have to cut it off because you can't get it out.
If you done already turned it over, punch through.
You can get your punch out pretty easy.
Never get
nothing
done today.
Morning, Mr. Allgood.
Good morning, sir.
I got about half a ton of iron out there for you.
All right, let's take a look at it.
Looks
all
right.
Let's get in.
Now, Williamsburg is fairly bustling.
You been busy?
Busy enough.
You know, I have always been of the opinion
that you are the best blacksmith I ever met.
You know me too well, don't you?
But what I have in mind is...
Oh, you see, my eldest son has his birthday next week.
He'll be 14 years old.
A fine lad.
I've been puzzling about what to get him.
And I think that he is ready for his own axe.
John, when are you going to mend this fireplace crane?
When I get around to it, I'll just lay it aside.
He's not a big boy, except for his dear mother.
And most of the axes I've seen of late have
been perhaps a little too large or perhaps too heavy.
I thought that perhaps you could make him one
a little smaller than usual.
That would be no problem.
Oh, I should like that. When could you do it?
Right now.
save another trip
Fine.
Making
the axe,
you would
pull it
down
on each
side of
the head
to keep the thickness of the head.
Then you would draw one side of the blade out then,
you draw the other side out,
and then you would bend the two together so you could weld.
Two people hammering a piece of iron,
that's double striking.
I'm using a small hammer, my striker's using a heavy hammer.
He's supposed to hit the exact spot that I hit.
That's where I want him to hit all the time,
because I'm watching the iron,
and he's more or less just watching just exactly where I hit.
Well, you have a signal, if you want him to stop,
you just drop your hammer over to the side.
You don't come back up. He knows to stop.
If I want him to hit it light, I'll start hitting real light.
If I want him to hit it harder, I'll hit harder.
And you have to stay in time.
If you didn't, you would hit each other's hammer
when you were coming up and him coming down.
For a good job, you've got
to have a good anvil.
You've got to have a good hammer.
And most of all, a good pair of tongs.
You've got to have all different size
of tongs to hold different iron items.
Flat, round, square, so forth.
If you've got a lot of this work to do,
you're going to have different shape of tongs for everything.
Very important.
You've got
to have
your
plucks in
there for
welding.
Anything that will melt and run is a good flux.
Anything that will cut the oxidation
from forming between the two pieces of material.
Sand is very good if you get a good,
fine white sand where you don't have too much grit in it.
In fact, I just assumed I had the sand
as the other type that I'm using now,
which is just borax and iron filings.
And a lot of times you can just use borax alone up there
on the iron filings all the time.
It
stays
tight.
If you rivet it on hot, it will loosen up.
You'll have to tighten it up again after it's finished.
Of course, the material expands when it's hot.
You can keep it straight. It won't bend.
In making a frame for a sign, it has to be very accurate.
It has to fit the sign.
You
can't
temper
iron,
so you
weld a
piece
of
steel
on
so you can temper it for cutting.
With a good fire, you don't have too much problem.
You have to be very accurate with your heat,
because the iron will take
a little bit more temper to it than your steel.
The town this morning, many lost his shoe.
You suppose you could put it back on again?
Yes, sir.
Much obliged.
Talking about your horseshoe,
you'd be surprised to know how many blacksmiths
probably never seen a horseshoe on.
They're not horseshoes.
You've got the ferrule.
That's all he does is shoe horses.
He's not going to forge it.
He don't get out and do ironwork.
But he knows enough about ironwork
that he can forge out a shoe.
But don't necessarily mean he knows
how to do the other ironwork.
The last
thing
you do
with an
axe is to,
uh...
Smooth it down real smooth and clean, and then you will grind it
to a sharp edge, and then you will temper it.
You want to keep it hard enough to hold an edge, but not too hard,
because it takes a lot of punishment, a lot of hard blows an axe takes.
So you'd rather see the axe to bend a little bit,
or mash just a little bit, than to be too hard and it would break.
When you cool the blade off at the point where you're tempering,
it's always hot back behind,
and the heat is actually going back into the blade down there.
You've got to have it shiny so you can see the colors.
You're going to see a light, bright color.
That's just as hard as you can get it when you put it in the water.
A straw will be a little bit softer than the shiny part.
And it'll be a dark straw, then the blue will come on.
And whatever hardness you want,
then you put it back into the water at that color.
And that's the hardness you're going to get.
Is this what you had in mind?
Oh, yes.
That ought to be just right.
I'll make a handle for it.
I'm sure he'll be pleased.
Well,
I
think
a
good
blacksmith,
he's
got to
have
a
good
imagination.
He's got to be very interested in what he's doing,
to take his time.
You can tell a good blacksmith when he uses his hammer.
And the heat that he's using, he's got to be pretty well coordinated.
It's the way he hits the material on the anvil,
and not playing around with it, making every lick count.
You can work on a lot of items,
and you're doing pretty good with it, maybe.
And then, just a few bad licks, and you're in trouble again.
You've got to upset, smooth out.
A lot of times, it's too thin. You can't upset.
You have to start over from the beginning.
Or he can have an item practically finished.
You get it too hot in your fire and burn the end off.
You've got to start over.
So I think time, patience, coordination,
that's what it takes to make a good blacksmith.
Some of the
objects
that you
make, you
would take
a file and
knock off
the scale
and smooth
for lamp black and oil finish.
It gives you a life to it.
It's not a completely dead color.
It gives you a very nice color.
That's the object for the lamp black.
I think any man would get a satisfaction out
of doing something a little fancier, a little
bit more decorative, occasionally.
I don't think you'd want to do this all the time.
You'd like to have some stuff that you can hammer out and throw down.
But it's no doubt in my mind, I think every blacksmith
should have wonderful satisfaction out of doing a fancy job,
something you'd be proud of.
Sure, I get a thrill out of doing it.
Good afternoon,
Mr. Burcham.
Good afternoon, sir.
Are my hinges made?
Yes, sir. Right over here.
Please, sir. All right.
It'll be a shilling five pence a pair.
Two and ten?
Yes, sir.
How much are the fire dogs?
Eighteen shilling.
Well done. Here. Compliments of the house.
Thank you.
The English coffee house. Do you like that?
A toast to our new addition.
Oh, I nearly forgot.
Old Jack's
been looking for you.
Thank you. I'll stop by and see what he wants.
There you
be, John.
I've been
looking
for you.
Oh, hello, Jack.
Hello, my friend. I'm glad I found you.
What can I do for you, Jack?
You know that our governor has given a ball tonight.
Oh, yes. I wasn't invited.
Nor was I, as a guest.
I understand that he's opened the Raleigh Tavern
to the public with free liquor for all, huh?
No, Jack, that was last October.
Oh.
Well, he desires to fire salutes
in celebration of the king's birth night.
I was just getting things ready, but I seem to be lacking a worm.
Well, I put some coal to the traveling forge here.
Well, I was intending to mend it myself,
but I seem to be missing some tools.
I must put a new lock on that door.
Well, I think we can make you one in time for the celebration.
Well, let me fetch it.
Mind you, it's got to be done by tonight.
No trouble.
Ah, very good then.
Worm is a very important tool.
It's made like a corkscrew.
And after you fire the cannon,
you would have to put the worm in there
to pick up anything that was left,
burning paper or something.
That would clean it out so you could load and fire again.
I don't know of anything I'd rather do than blacksmith.
Nothing.
I would never make a carp now.
I can't saw a straight line with a saw.
I can't drive nails.
I admire the gunsmith's work and all like that,
but I never would have the patience to do the gunsmith's work.
I don't like filing or grinding on a stone or something.
I like to hammer it out.
And you always feel good after you start to work in blacksmithing.
You get hot, it's hard and it's dirty,
but you can start to work when you're feeling tough in the mornings
and in just a few minutes you're feeling pretty good.
It works it right out of you.
I really don't dislike any part of it.
I don't dislike the hard work, the dirty part.
The heat don't bother me too much.
The only thing that bothers your time
is people bringing the stuff to you to make.
Then they have to sit down and tell you how to make it.
That kind of gets next to you.
You can't say too much to them.
After all, you're doing the job for them.
But you like to make it like you want to make it.
If it comes out to look like he wants it to look.
But I really don't dislike anything about it.
Now, I don't know of anything I'd rather do.
I've always been happy with a blacksmith.
Shut
this
off the
magazine
on your
way
home.
All right.
Good night.
Good night.
Papa.
Hello, Susan.
Mama wants to know if the crane's mended yet.
Uh-oh.
Come on.
We're going back in.
.
All right, we'll mend it.
Good.
Let's go.
Oh, we're going back in.
No no, we're going back in.
We're going back in.
We're going back.
Good.
This is so fun.
What?
Can we go out?
Yes, we can go out.
Oh, make sure everybody is at a distance.
Okay.
Ready?
Okay.
Let's do it.
.
.
You guys go first.
Okay.
Let's go.
.
Good.
You guys go first.
.
Okay.