Serger Seam Allowance Explained: You have been lining it up WRONG!

Sewing Tips
238 followers
Nov 17, 2026
0:00 Demystifying Serger Seam Allowances
2:01 Locating Your Stitching Line
5:16 Creating Your Own Custom Guides
7:18 The Ultimate Seam Allowance Test
AI Generated·May contain errors
Video Summary
AI GeneratedThis video explains how to determine and maintain correct seam allowances when using a serger. The core principle is that the seam allowance is always measured from the raw edge of the fabric to the left needle, regardless of the machine's blade or stitch width settings.
Where do you line up your fabric on a serger?
It's the question I hear more than almost any other.
And the answer is simpler than you think.
Today I'm explaining serger seam allowance
so you never have to guess again.
Hey SergerBees, I'm Suki, your serger coach,
and for over 25 years, I've been helping sewists
trade fear for confidence at their serger.
With a blade trimming as you serge,
it's hard to know where your fabric should go, but it's
easier than you think.
By the end of this video,
you'll know exactly where to line up your fabric for any seam
allowance, no matter which serger is sitting in your sewing room.
Let's get started.
Before we dive in, here's what I'm assuming today
so everything makes sense.
We're stitching a 4-thread overlock with the stitch width set to 6mm,
which is a very common default.
And we're talking about
the four most common seam allowances you'll see in patterns.
A quarter of an inch, 3 eighths of an inch,
a half inch, and 5 eighths of an inch.
But the concept is exactly the same
no matter what stitch you're making.
A rolled hem, a five thread with chain stitch and an overlock,
it doesn't matter.
You're always measuring from the needle.
Your measurements might change, but the rules will still apply.
Here's the good news.
A seam allowance on a serger means exactly
the same thing it means on a sewing machine.
It's the distance from the raw edge of your fabric
to your stitching line, and your pattern
pattern is what tells you.
How much it should be. When I design a pattern,
the seam allowance is one of the first decisions
I make. And when I'm making a project
from another designer's pattern, it's one of the
first things that I look for because it tells me exactly where
to line my fabric up. The only
difference on a serger is the blade, which some people call the knife.
It trims away any fabric
As you stitch and that's what makes it feel a little bit of a mystery.
So where is your stitching line?
On a four thread overlock your seam line is your left needle.
That's the stitching that holds your fabric together
and it's the line your seam allowance is measured to.
Everything to the right of that, the right needle,
the loopers wrapping the edge, is finishing the edge of your seam.
Now, let's talk about the blade and the needle
because they're two different measurements.
With our width set to six millimeters,
the distance from your left needle to the blade
is six millimeters, which is about a quarter of an inch.
If you want to be exact, grab a caliper and measure it.
But about a quarter of an inch is close enough for me.
That width is what's inside your seam forever and ever.
And if you change your width.
The blade moves closer to or further from the needle,
so the width changes with it.
That will change the look of the stitch
and honestly that's a conversation for another day.
So there are two things happening at once.
Your pattern gives you the seam allowance
and your serger gives you the width.
So now you're probably wondering, where do I line up my fabric?
Here's the answer, SergerBee.
You line up your seam allowance
with your left needle exactly like you would on a sewing
machine.
For example, let's assume your pattern calls
for a half inch seam allowance.
Grab a scrap of fabric and mark a half inch from the edge.
The distance from the edge of the fabric
to that mark is your seam allowance.
Now line that mark up with your left needle
so the needle sits right over the mark.
And if you don't want to mark your fabric, that's fine too.
Just line up where the mark would be with your left needle.
So how much does the blade cut off?
Whatever extra fabric is left past your width.
Let's walk through all four.
With a quarter of an inch seam allowance,
your width is already a quarter of an inch,
so the blade trims nothing at all.
We'll come back to that one in a minute.
With 3 eighths of an inch seam allowance,
the blade trims about an eighth of an inch.
With a half inch seam allowance,
the blade trims about a quarter of an inch.
With a 5 eighths inch seam allowance,
the blade trims about 3 eighths of an inch.
And in every case, you're left with that same quarter
of an inch of width inside your seam.
Whether your pattern calls for a quarter,
three eighths, a half inch, or five eighths of an inch,
the width stays the same.
Only the amount the blade trims changes. Now many sergers have
markings or guidelines on the throat plate
or presser foot that help you line up your fabric.
And some sergers even come with a seam guide you can set
to the seam allowance you need.
Here's the catch. They're different from machine to machine.
Some are measured from the needle and some are measured from the blade.
So take a look at yours and check your manual
to see what those numbers actually mean on your machine.
So now what if your serger doesn't have
the markings for the seam allowance you need?
No problem, you can make your own.
The easiest way is the one we've already used.
Mark your fabric and line that mark up with your left needle.
You can also measure from your left needle
and add your own guide right on the bed of
your machine using a strip of washi tape or painter's tape.
Just make sure it stays clear of the blade and the feed dogs.
Or a thin acrylic marker if you'd like something more permanent.
And when you're done with it,
a rubbing alcohol wipe takes it right off.
Now, let's talk about your blade.
Your serger was designed to trim as it stitches,
so most of the time, we let it do its job.
I get asked all the time, Suki, should I remove or lower my blade?
And here's my answer.
Unless you really are trying to avoid cutting your stitches,
leave your blade position alone.
The only time I say to lower
or remove the blade is when you're stitching in the round.
That's stitching all the way around a project in one continuous line,
like around the top
of a purse or the edge of a tablecloth.
I like to call it the roundabout.
When you come back to where you started,
it's easy to run into your own stitches and cut them.
And that's the one time you might want to get the blade out of the way.
But even then, I usually leave my blade up
and do my very best to avoid cutting the stitches.
If you do decide to lower or remove it,
just know that on some sergers that's a really quick and easy thing,
and on others it's tricky.
So check your user manual
and only do it if it's an easy thing to do on your serger.
Now, back to our seam allowance.
Sometimes we don't want to trim anything off at all,
like the quarter of an inch seam allowance.
We talked about it earlier.
For that, you still don't need to touch your blade.
Just line up your mark with your left needle
and keep the raw edge just inside the blade
so it isn't trimming anything.
So, how do you know if your seam allowance is right?
Here's my favorite way to be sure, and it works on any serger.
Cut two scraps of fabric, each 4 inches wide.
Line them right sides together
and stitch a seam using the seam allowance you want to test.
Now open it up and measure the total width.
With a half inch seam allowance,
your two 4 inch pieces should now measure 7 inches.
With 3 eighths inch, you'll have 7 and a quarter.
With 5 eighths inch, you'll have 6 and 3 quarters.
And with a quarter inch, you'll have seven and a half.
If your number is off, check with the needle
that you're lining it up with and check your width.
A quick test seam saves you from finding out
the hard way on your real project.
So always test on the scrap first.
So let me know in the comments which seam allowance you use the most.
And if you'd like to keep building your serger skills,
check out this video right here that
teaches you how to master gathers on a serger
with or without a gathering foot.
And until I see you next time, I hope you have a creative day.
