#repeater#chronograph#watchrepair In this video, I take on the restoration of a Henry Sandoz minute repeater chronograph pocket watch, which is a beautifully made, century-old movement that recently took a fall and hasn’t been the same since. The hands are frozen, the repeater doesn't chime the correct time, the movement is wound tight, and I suspect at least one jewel didn’t survive the impact. From disassembly and inspection to jewel replacement, pivot burnishing, and full reassembly, follow along as I attempt to bring this complicated mechanical watch back to working order.
Henry Sandoz was a Swiss watchmaker known for producing high-quality mechanical watches in the early 20th century. While not as well-known today as some of the major brands, Sandoz pieces (especially those with complications like chronographs and repeaters) were considered to be of higher quality. This example, with its minute repeater and mono-pusher chronograph, is a rare and challenging piece that shows the ingenuity of early Swiss horology.
Whether you're a seasoned watch enthusiast or simply curious about the world of horology, this video offers a captivating glimpse into how an amateur like me is trying to master the art of watchmaking.
This is a Henry Sandoz pocket watch and it's been through a lot.
It's about 100 years old. It's packed with a minute repeater,
a chronograph, and enough tiny springs to make reassembly a minor act of faith.
And recently it lost a fight with gravity and it's been holding a grudge ever since.
It's the, I'd say it's the kind of fall that leaves you hoping the damage is just cosmetic,
but let's be honest, we know better.
The watch is wound tight, the hands won't budge, and I suspect the jewel situation is,
well, let's just say I won't be surprised to find one or two casualties.
The watch, from the movement to the 14 caracal case it's housed in,
quite beautifully made, deceptively complex, and it does deserve a second chance.
So let's see what we're up against.
That's the sweep second hand.
Do the sub-seconds hand and then these two guys.
I could probably just do both of these at the same time.
Yeah, hmm, quite a bit of oil splatter on the inside of this guy.
What I found with repeaters is the gongs are installed and uninstalled
while the movement is still cased.
And with the gongs out, I can now see the case screw right here.
And there's no obvious way to release the crown other than this seems to be acting
like a setting lever holding the crown and stem in place.
So I'm wondering if I loosen up this little screw, it can pop right out.
Maybe.
There it goes.
And the pusher for the repeater needs to be removed as well.
Oh, look who woke up.
I fixed it.
All done.
Eh, not quite.
Another nice, actually convenient, aspect of repeaters that I've come to expect
is the press-on dial.
They're not held on by any kind of screws because there would be no place to put screws here.
And you want to be able to put the dial on when the movement's in the case
because under this dial are adjustment screws.
To adjust the repeater, which you would want to do when it's cased.
So you wouldn't want rim screws that are inaccessible when the movement's in the case.
So we simply just find a way to lever this off.
All right, how awesome is it going to look under here?
It's kind of grimy.
I guess the easy stuff can come off.
There's the dial washer, the arrow wheel.
Now the cannon pinion seems to be mounted to the snail where the repeater will hit this
and it'll actually detect how many chimes.
Yeah, I think that's all for now on this side.
This lower balance jewel.
Yeah, that looks pretty suspicious.
I don't know if that's stock.
Everything else looks so beautiful, relatively.
It looks like someone took a stone out of my eight-year-old's gem mining set.
That could be one explanation for the low amplitude.
The top side is beautifully finished.
What does this say here?
July 5th, 1929, I assume.
Service mark right on a plate.
Nice.
Well, they did things differently back then.
I think that's 100-year-old hair.
Servicing and repairing a repeater is no different than any other mechanical watch.
You start by removing the balance to protect the most delicate part of the watch.
And following this, we figure out a way to disarm the mainspring.
Come on, roller.
There you go.
And the next thing I like to do is separate the balance stud
so that this bridge can be stored separately from the balance.
And the pivots look pretty good.
Can't quite tell if that's just dirt or if they're chewed up at all.
We'll have to re-inspect after cleaning and then make a determination whether burnishing
is going to be required.
And the jewel, kind of about the same comment here.
Really doesn't look cracked.
I think there's just really old stuck oils in there.
Now I'm going to re-insert the stem for the purposes of letting down the
remaining power in the mainspring.
Okay, so now at least we know this movement's not a grenade.
The core movement is going to be disassembled last and all the complications
as early as possible.
So if we think through what the complications are,
one of them is this kind of monopusher chronograph.
We've got the reset hammer here.
It's a column wheel chronograph.
Love the feel of column wheels.
And then the various springs that lean against the levers.
You've got the drive wheels.
The drive wheels kind of transfer the power from the running movement.
And you can see the teeth on them are super tiny,
but once they touch it moves the runner wheel,
which drives that sweep seconds hand nicely around the dial of the watch.
That's the chronograph runner with the long extended pivot
that the sweep seconds hand attaches to.
Underneath you can see how the driver wheel sits within the bridge.
There you go.
Now let's go ahead and take that spring off.
Now the several springs that work against the column wheel of the chronograph.
This one seems to be the spring that indexes it.
All right, this would be the hammer spring.
So when the movement's in reset mode,
this hammer spring ensures that the hammer stays firmly planted against the runner heart.
This seems like it's part of the control arm.
And I'm just guessing here,
just I have a little bit of experience with chronographs.
This is my first time working on this caliber.
So forgive me if my terms are not 100% accurate,
but the fundamentals are the same.
The hammer just lifts off.
Now this can also then be removed in the column wheel.
I mean that's pretty much it for the chronograph.
It's a mono pusher.
It's a single sweep hand.
There's really nothing crazy.
Let me go for the repeater next.
This is a centrifugal repeater.
The centrifugal repeater uses a weighted spinning arm
to control the speed at which the gongs are chimed.
And some of these, the distribution of that weight is kind of adjustable
so you can control that speed to some extent.
All right, now I need to unhook and disarm the repeater mainspring,
which is preloaded using this mechanism here.
All right, and then that would be this guy.
And this rack piece.
But I don't think I need to take this rack piece off quite yet.
Oh wow, that jewel is so cooked.
These are the wheels of the repeater train.
That was the arbor.
And for some reason, this doesn't actually want to come out quite yet.
So I'm gonna have to do more work on the other side for that.
These are the two gong hammers.
And I'll leave them in place for now.
Let's see if I could replace this with a modern white alloy spring.
I know it's a lot shorter than a typical mainspring,
and it's got this little interesting curve on the tail.
So I'm gonna have to modify whatever I decide to replace it with.
Now I'm going to switch gears a little bit
and disassemble the core movement beginning with the pallet fork.
And then the small cock that is over the fourth wheel and the escape wheel.
I don't see any cracks anywhere.
This is the escape wheel.
And the fourth wheel with the extended drive wheel.
But I'm going to need to remove that other wheel in order to remove this wheel.
So that'll sit there for the time being.
This ratchet wheel seems to have an interesting...
Instead of being screwed, it's got this square nut over a threaded arbor.
It's kind of an interesting design.
Never seen that before.
It's kind of tedious.
I wonder why they did it this way.
Okay, now is this going to be normally threaded or reverse threaded?
Reverse threaded.
Interesting.
I love it.
This of course is the crown wheel.
And the...
I'm going to do the click spring first.
Now the click.
And then the bridge can be removed.
Now I can remove these wheels.
This one of course has the cannon pinion.
Attached to the bottom of it so I can't remove it yet.
I won't be able to remove the barrel for that same reason.
But the winding pinion and the sliding clutch can be removed.
Yeah, and then this operating lever.
There's no reason that needs to stay.
That's the other side.
More of the repeater hardware is over here.
This is now the minute wheel.
A stubborn minute wheel.
How about the setting gear?
Oh, she's tight.
That's pretty cool.
Interesting.
One of the many springs for the repeater.
I'm going to release that tension first.
I don't want this to go flying and lose the screw.
I mean, I can make screws but it's more annoying if I really don't have to.
All right.
Now this arm can be lifted off.
Oh, what's next?
Now this one looks promising.
Release the tension of this spring.
All right, this could be part of the minute rack.
It's based on how many teeth I'm seeing up here.
Yeah, I count 15 so it can chime and indicate how many minutes past the quarter.
And then this one that I'm removing now is the hours and the quarters rack.
So this will chime the number of hours and the number of quarters past the hour.
To be clear, it's not actually the thing doing the chiming.
Yeah, I think the cannon pinion is going to come off first before I can lift that away.
And this little interesting bit of kit here, as you're aware,
is there's like some hidden levers under here that allow the watch to kind of
manage whether there's an extra chime at the turn of the hour.
So there's some protection in here for a little bit more robustness
on how the repeater works at the turn of the hour.
Now I'll just go ahead and lift this off.
I mean, it's cool, but not as cool as the dragon rack that we saw in the Goliath watch.
These small teeth represent the hours.
And these larger teeth represent how many quarters past the hour.
This is a little index for the hour star.
And underneath the hour star is the hour snail.
So the repeater can detect how many hours passed.
Get these out of the way.
And so this is really the plunger that starts the repeater, winds it up,
and then upon releasing it, the repeater is let go and chimes whatever it needs to chime.
I don't think I need to remove this.
This is really just some modular plates.
There's really nothing under it that needs to get cleaned.
But now, yeah, we got a bunch more springs here.
Fun's not over yet.
Decisions, decisions.
I gotta remember how all this goes back together.
All right, and this is facing the camera, not me, so that adds to the fun.
So I'm going to work from my left to right, starting with whatever this spring is.
Oh, and then actually, that might have just been the yoke spring,
and then this here is the yoke.
Kind of your basic, typical yoke-yoke spring combination.
Of course, this is a, they call it a pin set watch.
Oh, this looks super delicate.
I'm going to now just go ahead and remove the rest of this repeater driver barrel,
wheel, whatever you want to call it.
That dropped through the other side, so there's a little internal click there as well.
All right, the rest of these springs are for the two hammers.
A set over here and a set on the other side.
And with all the springs out of the way, the hammers themselves can simply be lifted off.
I am just doing the pre-inspection to all the jewels on this plate.
A little dirty and some stuff stuck to them.
But again, this lower balance jewel, I don't know what the heck's going on here.
It looks like a piece of metal instead of a cap jewel.
Very crude.
Oh yeah, that is not...
It's a piece of mainspring, look at that.
Nice.
I guess that's one way to do it.
The whole jewel looks fine though.
Organized chaos.
This is the barrel arbor.
Just walk it out of the barrel.
What do we have here?
Replace this.
Worst case, I need to make a new one of these.
But in the spirit of preservation, I'm going to see if I could just ream it out
and fit a friction style cap jewel.
Let's start with you.
And I'm just going to work my way up one or two sizes until I end up with a nice round hole.
Just have to pump out this broken jewel.
There we go.
And then ream it to size so I can fit a replacement friction jewel in.
As before, you just have to press the jewel into place.
Now this upper balance pivot doesn't look too healthy.
It's not bad, but it's a little bit chewed up.
And you see how the...
Feel closely the very, very tip of it.
It's got like a little hat.
They call it a mushroom.
And see how the lower pivot looks a lot nicer.
So we're going to burnish these pivots and see if we can't make them look the same.
The first step to doing this is to gently lever off the hairspring.
You can't have the hairspring on during the burnishing process.
Yeah, you see there's a little speck of rust on the hairspring too.
So much we can do about that.
Now the pivot's a size 12, so I need to exchange the runner with one that has the right size.
I'm going to put my bow on it.
On the headstock, this is what I'll use to spin the wheel as I'm burnishing.
And mount the balance wheel.
And the working end of the balance wheel goes on the tailstock runner.
And so that's fixed in place.
Now this burnisher has been lightly oiled.
One of the sides is a little bit rounded.
And that'll allow me to kind of keep a safe edge against the conical shoulder of
the balance staff pivot.
Let's inspect.
Yeah, that's 100% better.
Look how smooth that is.
See, now it's even better than the bottom one.
The bottom one was looking really good.
So I'm going to go ahead and do the same for the bottom, and then we'll put the hairspring
back on.
Now I'm just restoring the hairspring to its original orientation using a reference mark
that was on the balance.
This is this little mark here that corresponds to where the stud needs to go.
So I'll just go ahead and make sure that's rotated around properly before I stake it
down.
I have to do that with a little screwdriver off the side.
Oh, and by the way, I'm pretty sure this was just a little surface corrosion on the
balance spring here.
I don't think that's going to be a major issue.
So now the goal is to scrub all of the jewel holes with a piece of pegwood to get rid of
any old or really stubborn stuck-on oils.
That'll help jumpstart the cleaning process.
And I even like to touch on any kind of bearing surface, including where the barrel arbor
goes.
Especially important for the underside of a lot of these bearing surfaces.
That usually will have some good kind of sticky oils right there.
That's good to get off, not just the inside of the surfaces, but also on the underside
as well.
I won't show all of them here, but you get the idea.
All right, and I know I said I would reassemble things in the reverse order that I took them
apart, but while I was disassembling, I kind of realized that there was some awkward things
that I did with the order of those operations.
So I'm going to take things a little bit differently during reassembly.
There's a notch on the barrel on the inside to catch the tail.
Just a couple drops of HP 1300.
Now I bought this spring based on its specifications, and unfortunately it's not...
It doesn't have the exact width, so I can't just press it into the barrel like you're
really supposed to do with these.
So I'm going to have to unwind it out of here and use a mainspring winder instead.
Oh well.
Now notice the difference in how strong this mainspring is and how wide it coils compared
to this old one.
This is what they call tired.
All right, now it can be just shot right into the barrel and a little bit along the bearing
surface.
Finally this arbor can be fitted, and then the cap or the lid.
So like I said, I'm going to do things a little bit differently this time.
I'm going to start by seeing if I could just reassemble the core movement first,
get that running, and then work on the repeater, and then finally the chronograph.
Before any of the wheels go in, I'm just inspecting them under the microscope to make
sure all the teeth are clean, there's no debris left in there, all the pinion leaves are shiny,
none of the pivots are going to need any kind of burnishing.
We can address that if we need to.
I just go ahead and do this for each one right before replacing the movement.
It's really just kind of one last double check to make sure everything's clean.
Yeah, the escape wheel as well.
Look how tiny those pivots are.
I had to repivot one of these before.
Not fun.
And finally the big old center wheel.
The fourth wheel with the extended pivot for the seconds hand will go in first.
And of course this is the one that has the mounted drive wheel on top for the chronograph.
And then I'll go ahead and just slide in the third wheel.
And then for the center wheel, I usually like to put a little bit of HP1300 within the bearing
before it gets put in because it doesn't have the same kind of oil sink that the other pivots
would have.
Before that barrel bridge is installed, I'm just going to lightly lubricate the barrel arbor here
and make sure the pivots are seated.
Looks like they are.
It's really just the second wheel and the third wheel here.
Now the escape wheel that's right next to that fourth wheel.
And as is tradition, I always inspect the jewels as well for any kind of
contamination that didn't come out in the wash.
This thing's kind of awkward.
All right, this fourth wheel pivot's seated.
I'm not sure about the escape wheel yet.
I think I got it.
All right, now it's time to reinstall the ratchet wheel.
And if you recall, the ratchet wheel is secured by this interesting square nut.
And then the crown wheel.
And this is reverse threaded.
Oh, and while I'm here, I'll do the click.
And finally the click spring.
As I'm approaching the final steps of the core movement assembly,
I'm going to go ahead and oil these pivots.
I do like doing this under the microscope because you can see
precisely how much oil is getting sucked into the oil sink.
When it comes to oiling these pivots, less is more.
Now a little bit of grease to go on the tips of these pallet fork stones.
And now to reinstall the fork into the movement.
And it's going to be really important to make sure that top pivot is seated.
There we go.
I'm just putting a little bit of this Mobius blue grease.
I also put a tiny little grease here on the sliding clutch where the yoke will ride.
And the winding pinion will go here.
And the sliding clutch right in front of it.
Here is the yoke.
And this part of the yoke is what's activated by the pin set lever.
When you press that little pin on the case to set the time.
Let's get that screw mostly home and then slide that spring over.
And finish the screw off the rest of the way.
So with the winding pinion and sliding clutch in place,
I can now at least attempt to wind the watch a little bit.
Just get a little bit of wind in place with just a couple of turns here.
That's really all I'm going to do.
A bit of 9010 on this new capsule.
This will be where the lower balance pivot rides against.
This is the regulator arm and this is the capsule for the upper balance pivot.
And the regulator arm is fixed to the balance cock by way of the screws that go into that jewel setting.
So as shown, the balance bridge goes right up on there.
Just have to line up the holes.
Now to deposit some OBS 9010 oil using the automatic oiler.
That triangular shaped balance spring stud needs to go in here and I'll have to tighten this screw down.
The other important thing is to make sure the balance spring made its way into the regulator pins.
Alright, this will be the moment of truth.
Let me get this balance installed and see if it ticks.
Oh, oil wants to come alive.
Balance isn't even in place yet.
That's encouraging.
Gotta find those locator pins.
I think we're in good shape.
Looks like it's running pretty decently as well.
Now I haven't regulated anything yet, but speed error is almost a millisecond.
For a fixed stud carrier, anything under one millisecond is considered acceptable.
You know, I try to strive for maybe half a millisecond, if that.
So I think I'm going to try to just see if I can pull that in just a tad more than where it is right now.
And to do that, you need to rotate the hairspring collet by very minute amounts,
either clockwise or counterclockwise.
So this is very delicate, very delicate work.
You probably barely even saw that, but I moved it just slightly clockwise.
Now I only just did the smallest amount of regulation.
Obviously, 24 hours are really going to have to pass until oils completely settle in,
at which point I can derive a final rate.
But I'm pretty happy with the beat error, very happy with the amplitude.
Okay, so gaining a little bit vertically.
That's probably not unexpected for a watch of this age.
Amplitude's still quite healthy, though.
But it's really important that this watch is performing as it is right now
before I start adding back all the hardware related to the chronograph or the repeater.
Because if there turns out to be an issue,
well, that's going to be a lot to remove to try to debug what's going on with the wheel train.
And as expected, the horizontal positions are going to be its favorite.
Less friction throughout the train, higher amplitude.
Overall, this is pretty good.
I'm satisfied with this result.
Now to reinstall the governor train.
And I went ahead and uninstalled the balance to give myself some room to work.
I'm pretty sure the balance would have gotten in the way here,
or at least made it a little more challenging when it comes to seating these pivots.
And this is one of the hammers, and then the other hammer.
So I have here an old mainspring that happens to be the right height
and the right thickness, in other words, the right strength.
But it's automatic, so I need to essentially kind of shape this
to have that little curve in the tail, just like this one had.
So I can grip onto that little corner.
I did measure the length, and it is kind of...
ends up to be about here, so snippity-snip-snip.
Now the next step is to anneal the end of the spring into this alcohol lamp.
Gently holding it over the flame until it hits a kind of a dull red color.
I don't want it to air harden, so I don't want it to get to that bright red.
But just to kind of wave it back and forth, keep it heated.
And that will allow me to bend it without it breaking.
Last thing we want is it to be too brittle to bend.
And that should be enough.
All right, that'll be sufficient.
All right, so here's the deal.
I don't have a mainspring winder that would necessarily work with this.
The size of the mainspring harbor is too large.
The size of the opening that the spring would be ejected into is too small.
I'll probably do more harm than good trying to force a winder to work in this situation.
Also, there's a very delicate jewel on the other side there,
and I don't feel right about pressing the arbor in after the fact.
So I'm going to gently install the winding arbor on there now,
prior to installing the rest of the spring into the opening.
And then finally the bridge for the repeater, now complete with the new jewel.
So I not only have to seat the three train pivots,
I also have to seat the two hammer pivots.
I might have to do this off camera.
Just oiling these pivots.
Now the centripetal governor.
There's only one direction that this could be installed.
This too also has pivots that get lubricated.
So if we were to put a little wind on here,
then the governor train is really rate limited by the centripetal forces of this governor at
the very end of the train.
So it won't let the spring power be released any faster than this can rotate.
Now the hammers themselves are sprung using this lever that protrudes.
So working on this hammer first,
there's a set of springs that kind of sit against it and sort of govern its motion.
This piece here is actually not a spring,
but more of a backstop that controls the depth of the hammer.
And this here would be the actual spring.
This backstop will require some adjustment.
This is the activator.
This is what essentially presses on it on the hammer.
And similar story with this other hammer.
Shifting over here for a little bit, we have the repeater activating lever.
That's fitted with a shouldered screw which allows the lever to rotate.
And then there's this other sort of piece to that drive rack.
And this is the piece that directly interfaces with the arbor of the repeater main spring.
And this is also fitted with a shouldered screw.
When that activation lever is pressed,
this rack kind of winds up and drives one of the racks around this arbor and
essentially winds it up so that this thing can release its power.
So I need to put a little preload on this and then fit the rack to it and align it with this one.
On second thought, this really needed to go on before this.
So I'm going to need to remove this real quick and slide that on.
So what I'm going to do is I'm going to wind this guy up, preload it,
and then I'm going to have it sitting on a piece of rodico on the other side so the
governor won't be able to kind of spin it away.
And that'll give me enough time to re-situate the rack.
And I'm going to let it strike the hours and then I'm going to stop it.
And then I'm going to refit this rack in such a way where it hasn't quite activated yet.
This might be a little bit of trial and error to be completely honest.
If I press this activation lever over here, let's see what happens.
I'm going to have to spin it around to get to it.
All the way in.
Doesn't quite make it to all the hours.
This is where the trial and error part comes in.
Standby.
At 12 hours, we should have 12 strikes of the hammer.
And then the quarters will go and then the minutes past the quarters will go.
So now I can install the snail with the hour star on it so that the repeater can detect
how many hours has elapsed since 12.
And then there's also a little index jumper for that hour star.
There was another screw here but I seem to have misplaced it.
It's in the pile somewhere.
I just need to locate it.
I'll come back to that one.
Now this is the part of the repeater that's responsible for the quarters and the minutes.
And there's the kind of crazy looking cannon pinion
but also has the quarter snail at the bottom of it.
So now I need to set the part of the repeater that controls the windup of the quarters and
minute rack.
There's a little taper pin that goes in here.
So now I'll demonstrate what that looks like.
Now of course there needs to be a way to keep that sensor sprung against the snail
and that's what this spring is for.
And then what's still missing is the minutes sensor and rack.
So the way the sensor works is it sits up against one of these little minute snails
and each of these snails represents a quarter of the hour so it detects how many minutes
past the most recent quarter.
And then there's another spring whose purpose is to keep it sprung against the snail.
And this lever here works with the rack to make sure that the quarter and minute repeater
rack chimes the correct number of minutes.
You'll see how it grabs it and pulls it along.
There it goes.
It kind of grabs it and pushes it along.
Let's see what's next.
All right we're moving on to the minute wheel and the setting gear.
That's a wee bit loose isn't it?
Now these are screwed in posts so really just a matter of wrapping a pin vice around that
and tightening it.
So now the minute wheel can go on but I need to hold back this arm and this little piece
kind of secures them both down so they don't slide up in a way.
That's pretty much it for the repeater side.
The other thing I can do is reinstall this operating lever
and there's another shouldered screw that attaches the operating lever to the plate.
And this operating lever is acted on by the pusher and over here is where it'll work against
the column wheel of the chronograph itself.
As for the actual column wheel, that'll go right here.
9504 grease and another shouldered screw.
And this is the chronograph runner brake and I'm going to lightly grease the tip
that interacts with the column wheel.
What's really neat is the hammer just sits over this post here
and this piece that will sit on top of the operating lever will get a little bit of grease
as well.
And this is the operating lever spring and this makes sure that little operating lever
piece that sits against the column wheel is continuously sprung against it.
Now installing the hammer spring.
Its position will need to be adjusted once I get the screw started.
And another spring, I believe this one's specifically for the column wheel itself.
So I'll need to put a little bit of grease on that spring because this is what
kind of indexes the column wheel with the help of that kind of little puller
attached to the other end of the operating lever.
I believe that is the spring for the sliding clutch.
The sliding clutch itself consists of several small pieces.
I'll go ahead and reassemble them here before installing the clutch onto the main plate.
There's a post on the underside of the sliding clutch that I'll
lightly lubricate and then it kind of drops right into this hole.
And once I do that, I have to set the spring.
So I kind of have to just help it along.
There's a specific slot on the sliding clutch for that spring to go.
And with that spring set I can bring it home the rest of the way.
Now the sweep seconds hand is driven by this chronograph runner
with these tiny tiny little teeth and they're very delicate.
I'm going to need to be extra gentle with it.
And of course the heart in the middle is what the
the hammer leans against to drive it to its reset position.
And just need to seat the pivot like so.
Now I would like to put the balance back.
Let's see how this all came together.
All right, everything seems to be running well.
It looks like we're in the mode where the chronograph is running.
You can see the sweep seconds center runner turning.
So if I press this operating lever, I cause the sliding clutch to move out of the way.
Sliding clutch is no longer contacting the center runner.
If I press the operating lever again,
the reset hammer drives against the heart of the center runner
causing the center seconds hand to go back into its reset position.
Pressing the operating lever again returns it back into a running state.
As you can see the meshing of these teeth together is very delicate and very precise.
I'd like to move on to final steps but I need to tie up a loose end first.
Now let's see if I can get this shimmied into the case here.
There's the case screw right there.
How big a pain is it do you think it's going to be to get this setting lever back in place?
Oh please don't roll into the movement.
Please don't be a good screw.
Now I need to see if I can get this repeater pusher screw into that spot again.
Now the gongs can be reinstalled in the case.
I expect this to not sound so great.
All right, got work to do.
What I ultimately did was through a bit of trial and error
adjusted the the end stop for each of the gongs.
So there's one here, one over here,
and that allowed me to really dial in how much the hammers were hitting the gongs.
Sounds much better.
That jittery chronograph runner wheel was bothering me
and I suspect it's because the friction spring is kind of worn down or formed out of place.
So I'm going to see if I can't get a little bit more life out of that.
Nudge it in a little bit here.
So now it's just going to lightly rest against the side of that arbor
which should provide it just enough resistance so that it's not all twitchy.
That jitteriness is all gone.
So all it was it was just the friction spring not really doing its job.
Now the hour wheel can be fitted along with the dial washer and then the dial.
So the next step is to set the hands
so that the hands and the repeater agree on what time it is.
So first I need to figure out what time the repeater thinks it is.
2.58.
So if I just advance such that it's exactly at three o'clock I can set the hands up three.
And as a way to just double check something I go to 3.20.
Oh perfect.
Now if I were to go to let's say 3.38.
Now the sweep second chronograph hand can be installed while the chronograph's in reset mode.
Just check the chronograph make sure that works properly.
One thing that always worries me is whether the
pipe on that sweep seconds hand is strong enough to withstand the reset action.
Sometimes it slips along the center post and I've had to make new ones in the past.
So we'll let it get to the furthest point
to really test to make sure that it can jump all the way back from that point.
Let's see right about there and let's see if it resets.
Oh beautiful.
So that's pretty much it.
I really hope you learned something from this video today and if not I hope you found it
really enjoyable to watch.
Repeaters are one of those special challenges that I really enjoy and chronographs are always fun.
And with that thanks for fixing watches with me today and I'll see you in the next one.