#restoration#watchrepair#clock This is the most expensive broken watch (or clock?) I've purchased on eBay. It was sold to me at a "discounted" price of about $1,600 due to issues that I'll uncover and repair in this video. It's hard to call this a "deal" at that price, but in the end it was worth it.
World War II created a dire chronometer shortage for the United States. Before the war, most chronometers for American military and civilian customers were imported from Europe so we had that unfortunate supply chain dependency on that part of the world. In 1939, anticipating war, the U.S. Naval Observatory sought American watch manufacturers to mass-produce chronometers. Hamilton and Elgin participated, but only Hamilton met the Navy’s accuracy standards. Early 1942, Hamilton’s prototypes were selected after passing with a +/-1.55-second daily error rate. During the war, Hamilton produced approx 8,900 chronometers for the Navy, 1,500 for merchant ships, and 500 for the Army. In contrast to other movements of the time, Hamilton incorporated the detent escapement and the helical, corrosion resistant elinvar balance spring to maximize the accuracy it could produce.
These chronometers were specialized timekeepers for determining longitude at sea. A chronometer set to a known time standard like Greenwich mean time, allows sailors to determine their longitude by comparing it to local time. Since one hour of time difference equals 15 degrees of longitude, the time gap between the chronometer and local time reveals the ship’s longitude.
Today's repair is going to be a little bit different. I'm opening a package containing
a Hamilton Model 21 Marine Chronometer, and these were produced for the Navy during World War II.
I got a really nice deal on this one, and you'll soon find out why.
Now, like most proper chronometers, these feature a detent escapement,
which makes them super delicate and really finicky to work on. In fact,
there's an entire protocol that must be followed prior to even shipping one of these,
such as arresting the balance, blocking the train, or placing the precise amount of wind
into the mainspring. Now, being the highly rated eBay seller that he was,
the guy I bought this from had already packaged it up and had sent it on its way to me by the
time I was able to reach out to him to walk him through those steps. Can't really blame
him for not knowing though. Anyway, I'm a little bit nervous on the state of things.
Doesn't look like the gimbal is really set up correctly, but I guess we can address that later.
Now, before I start messing with this, I do want to engage the balance stop. This is really
what I wanted to have happen before the chronometer was shipped. It prevents the balance wheel from
moving without any load on the train, and if that were to happen, potentially damages
the escapement itself. With that done, now I can remove the chronometer itself from the gimbal.
I've never seen the inside of this, so I don't have any idea on what to expect in terms of the
condition. I think the crystal is pretty well scratched up. That's a shame. The last thing I
want to do is touch any of the hands while the movement's in such a delicate state. Oh wow,
so that definitely smells like the inside of a ship. Super cool. It's like diesel engine.
This is where that little allen key tightened down this lever that actually has a fork and like
two little rubber grommets on the end of it that make contact with the balance wheel. In doing so,
it makes it a little more convenient to transport and service. As I had suspected,
the movement is completely run down. Whether that even matters, we'll find out.
The next thing I need to do is lower this train blocking screw that's supposed to jam up the
movement. You can kind of make out where this screw is right there, and this is the fourth
wheel right here. So that's nice and jammed up. So now I'm going to wind the fuse chain
completely onto the fuse cone. This will actually make it a little bit easier to disassemble.
Oh, and there's a jam. Look at that. So this is what the seller was mentioning. He was under the
impression that it was fully wound up, and this is probably why. So apparently what's happening is
the fuse winding stop work bar is making contact with the stop work post that's protruding down
from the top plate. What's supposed to happen is the chain winds its way up the fuse cone
and presses in this stop work push bar, which then sticks out from the other side of the
fuse cone, and then makes contact with this post, and therefore then prevents any further
movement of the fuse cone. It's supposed to spring back out, so when the chain comes back down,
the bar retracts back into the cone, and then you're allowed to wind the cone again.
I feel like I can kind of just convince this bar back into its home. I would consider myself very,
very lucky if that's the only thing that's wrong with this movement, and that's why the seller was
getting rid of this for parts to repair. All right, with the the bar kind of retracted,
let's see if I can make it clear. Now it's time to let down the power in the mainspring.
You can't use the winding key because they've already designed the winding key, so you don't
accidentally try to wind the watch clockwise. Remember, fuses are wound counterclockwise.
So I'm going to use a simple clock winding key. The brass container was designed with a specific
cutout so you can contain the movement inverted in that notch while the dial side's safely tucked
inside here. I'm just going to gradually do this a little bit at a time, and that's it.
Now I can release the hairspring stud. Before I lift away the balance cock and the balance,
I'm going to go ahead and uninstall this balance stop add-on that the shipyard put in at some
point. No shortage of oil stuck under there. Smells great, by the way. Remove the balance
cock safely. I'm kind of going to just steady this balance because I don't... the last thing I want
is to have it jam against that very delicate detent. Just gently pull it away. Beautiful
helical spring looks great. So the lower pivot looks good. This is the impulse jewel,
and this is the unlocking jewel. They look absolutely filthy, but no chips. And this is a
two-part roller. And then as for the top balance pivot, also looks beautiful. No concerns there.
The balance spring itself looks clean. No signs of corrosion. No concerns here.
The upper endstone cap of the balance cock can be removed. The upper cap jewel is a little dirty,
but good. And the upper balance hole jewel, about the same. No cracks, no chips. Let's try these.
Okay, you know what? I'm going to use a puller. That wasn't too bad. I wonder what that was for.
Oh, I don't like extra parts. All right, well, mystery number one. I need to undo the dial foot
screws. Now the dial can just be threw right off through this slot. Now I'll remove the wind
indicator wheel, the hour wheel, the minute wheel. The kind of opinion is if friction fit onto the
second wheel, just like many other watch movements. One thing I almost forgot to do
is relieve any power in the Harrison's maintaining spring, which would be this.
And that's all that's needed. Now with all the spring power removed from the train, I can proceed
to remove the upper bridge of the escape wheel. And the escape wheel. The upper escape wheel
cap jewel and hole jewel look healthy, just a little bit dirty. And I'll now go ahead and
separate that cap jewel from its respective hole jewel. The next thing I'm going to do is remove
the detent block. Essentially the assembly that houses the very delicate spring detent,
which is the integral part of the escapement. So I'm supporting the block with my brass tweezers
as I loosen this screw. But now it's coming out. I just gotta be very, very gentle with it.
And here it comes. Attached to the detent block, we've got the detent itself. These are very,
very thin pieces of steel that act as a spring. This here attached to the detent is the trip
spring. And then there's also the locking jewel. All extremely delicate. You can see how thin these
pieces of steel are. So I'll be super careful with the cleaning process of this. This is not going
to go in the basket with all the other parts. So I can breathe a little bit easier now. The
disassembly from here on is a lot lower risk. This of course, if you remember from earlier,
is the setup ratchet. It's responsible for carrying the preload or the first couple of
lines into the main spring in a way that cuts off the least accurate portion of that spring.
So this is a number two key in case anyone's following along. Now I get that click out of
there. And finally the setup ratchet wheel itself. Now for the dust seal. There we go.
Just kind of convince it free. Yeah, it's a bit sticky. That's the winding stop. I can go ahead
and remove the barrel, ensuring that the chain has kind of, with slack, kind of automatically
unhooked itself from the hole on the side. So the barrel can just kind of be lifted off here.
Oh yeah, that was sticky. So then this is the the troublesome stop lever that really should be
under spring power, but it seems to just kind of float back and forth at will. Just like that.
With the train bridge out, I can remove the fourth wheel, the center or second wheel.
Very sticky. And the third wheel. I must not forget the maintaining click.
All right, the state of the jewels in the train wheel bridge. Two jewels that are in the potence.
This capital one here is for the balance. You notice on the on the right hand side there are
witness marks, so it looked like there was some opinion about how this cap plate should be
oriented. So I'll have to keep that in mind for reassembly. I will remove the movement plate
itself from this retaining ring. This is the lower cap jewel for the escape wheel.
Yeah, like the others, these jewels are quite filthy, but nothing's wrong with them. They're
just dirty. Look at that piece of fod here. So I'll be honest, this kind of scares me.
I bet the mainspring in here is pretty beefy. Let's get the barrel lid off and see what we're
working with here. I've never worked on anything this large. A lot of respect has to be given to
these springs. Oh man, that is a beefy arbor. All right, well what's this here? What is this?
Where'd you come from? What is that? Is that just, is that like dried up oil or something?
Yeah, it's just dirt or something because that's, the rest of it's just coming right off the
hole here. And slowly just kind of walk it out of the barrel gently.
All right, it's got a little tail in there. Or when it's wound up, this notch
just kind of sits against here.
Now I'm going to carefully unwind the chain from the fuse cone.
Kind of keep an eye out for any damage if I see anything, but I'm pretty sure the
chain was in good shape. So my goal here is really just to do it in a way that
doesn't allow it to kink on itself. This final link in the chain has a hook on it and that's
attached to a little post within the cone itself.
So this chain will be just stored off to the side for now, prepared for cleaning.
To disassemble the cone, there's a small pin here that needs to be
pressed out from one side. And I did notice that there's a little dimple
right here that maybe a past repairman made as a reference mark.
Base can be lifted away and this is a separate piece here. So these are the winding clicks.
This would be the maintaining ratchet wheel. Again, that allows the watch to continue to run
while it's being wound. I've read about 10 minutes worth of power in that little spring
that's under this plate. There it goes. And there is the maintaining spring or sustaining spring.
I don't know if there's really any advantage to trying to remove these springs.
The clicks look like they may be riveted in place onto their respective posts,
so I don't think these are going to come off necessarily. And now the winding ratchet wheel.
And now I can turn my attention to the top plate that houses the sprung bar that's supposed to be
used to stop the winding when it's full. I'm expecting to find a broken spring under this
plate. So let's see. That's the bar. There would normally be a piece of that spring that's
protruding and sticking into that hole. Yeah, it's definitely shorter than I think it should be.
The remaining piece of it. The left-hand side is fine. However, the right-hand side I think had
to curve further around and then attach into that lever itself. As is tradition, all bearing
surfaces are scrubbed with pegwood. That really gives the cleaning process a really nice head
start. All the old oils kind of get stuck and dried on the inside surfaces of all these, so
every little bit we can do to help that process along will be to our benefit.
The escape wheel and the detent are a little more delicate, and so it was recommended really just
to soak them in cleaner. I'll give them a really brief, quick, super quick rinse in alcohol as
well. I say quick because the one jewel that's on the detent is shellacked in place, and we don't
want the alcohol to compromise the integrity of that shellack, so it's going to be just a quick
rinse in alcohol, which should be fine. As for the balance, it has a platform so it can sit within
a cleaning basket, and I'm actually just going to clean this through a traditional method
through the cleaning machine. In doing so, it will be more thorough clean than the ultrasonic,
and it just so happens that the 15 gauge guitar spring happens to be right about the same size,
within a hundredth of a millimeter. For those that haven't learned this little hack,
guitar spring is actually a perfect substitute for a watch spring. It's got just the right temper.
The only trick is just getting it to the right shape. There was a little finagling that had to
go on, but it's just about the right curvature. Something like that. So there's a little bit of
this 9504 grease that I'll put on the sliding surfaces for that lever. So now that end of the
spring has to go into the hole of this lever. The whole thing kind of has to get put into place all
at once, hopefully without it flying out of my hands. Now before I put the top cover on this,
I put a little bit of grease here. So normally the lever is sort of out of the way of that post,
and then once the chain is wound fully around the cone, at the last run it's going to press
against this part of the stop lever. The stop lever will stick out and that stop lever will
catch the post that's hanging down from the bridge. And then once the the train actually
winds down a little bit, the chain winds off the cone and it springs back. So the spring action is
what was missing, and was the reason why the seller was saying that they couldn't put any
kind of wind in it without it feeling like it was overwhelmed. Now we'll go ahead and install
the winding ratchet wheel, oiling the posts for the winding clicks here. It can also benefit from
a little bit of grease where the pawl springs make contact with the clicks themselves. And as
for the sustaining spring, I'm putting some grease here. This is really the business end of
the spring itself that's going to be the part of it that's moving around the most.
And then I just have to locate the pin. But we're not done there. We're going to put a little bit
of grease. This is kind of the lip of the fuse wheel that'll actually slide, because remember
if the fuse cone is is multiple pieces. So this is a metal on metal surface, and we just want to
sure that it's got enough grease here to mitigate wear over time. Just a little bit on
this part right here. Now I'll lightly grease the teeth of the ratchet wheel,
and then also the arbor above the ratchet needs some grease. And then this contact point.
All right, so we've got that and that. Now the sustaining ratchet wheel can be married to
the rest of the cone, making sure that the the winding clicks are situated properly
around the ratchet. And now the fuse wheel can be in place, taking care that the end of the
sustaining spring, that little post there, lands right there on the sustaining ratchet wheel,
like so. And then more grease is applied to this elevated area. All right, now for the final step,
I have to remember to put this back in the same orientation it was so that the taper pin can go
back in in the same hole, because this hole is tapered after all. So now we're just going to do
a little tappy-tap-tap to kind of secure it a little bit. And that's really it. Buttery smooth.
All right, so this small clock mainspring winder is a bit smaller than I was expecting it to be,
and this arbor is going to be way too small to hook onto the mainspring,
so I'm gonna have to improvise a bit.
So now I've built this custom winding arbor for my tiny clock mainspring winder. I just hope that
this little guy is going to be strong enough to withstand the force of the spring, because that's
really all I can fit inside this little winder, which could be undersized for the job, but it's
only one way to find out. I'm just lubricating the spring by running it through some watch paper
will catch the arbor. Yep. The jewels are, of course, re-inspected after cleaning prior to
reassembly. The bushings as well, even the non-jeweled bushings, are inspected for scoring
to the inside of their bearing surfaces. Not just the jewels, but the surfaces of all the arbors,
the pinion leaves, the teeth, the wheels. All this matters. We'll have a material impact on
the performance of the timepiece. And finally, and most critically, the detent itself mounted to
the block. Now I'll reinstall the lower end zoned cap for the escape wheel, which is going to go on
this jewel here. I'm going to put a nice drop of oil right in the center of it with OBIUS 9010.
And you can kind of just make out that perfect circle of oil, kind of on the outside of that
center circle of the jewel. And now I can begin putting in the train of wheels, starting with
the third wheel, the center wheel, and the fourth wheel. And let's not forget about the sustaining
pawl, something I typically do with with these kind of watches. It's always the afterthought.
This is the lower balance bridge, a droplet of 9010 right in the center of the jewel.
A couple of witness marks here, maybe as a guide. Maybe someone thought that was important to
ensure this side of it lines up with that side. Now I'll carefully lower the upper train bridge
onto the three pillars. Yahtzee. It's also a good time to just verify the end shake of each of the
wheels. We don't want anything to be too stiff. It's really good freedom of movement and don't
need to go crazy with it. So this is really just a more of a protective coating. I'm just going to
run it, cycle it through a couple of times. Now it's time to wind the chain back onto the fuse,
except for maybe the last turn or two. All right, so this is probably fine. Kind of hold away this
maintaining click. Over 10,000 of these Model 21s were made by Hamilton, mostly in 1942. World
War II created a bit of a shortage of chronometers for the U.S. Before the war, most of our chronometers
for the American military and the civilian customers were imported from Europe, so we had
that unfortunate supply chain dependency on that part of the world. But fortunately, in 1939, when
they anticipated the war, the U.S. Naval Observatory sought American watch manufacturers to mass
produce chronometers. Hamilton and Elgin both participated, but only Hamilton was selected.
Next, I need to re-lower the train blocking screw. During the war, Hamilton produced 8,900
chronometers for the Navy, 1,500 for merchant ships, and 500 for the Army. In contrast to
other movements of the time, Hamilton incorporated the detent escapement and that helical corrosion
resistant Elinvar balance spring to really maximize the accuracy it could produce.
And all this will pretty much go over the fuse winding square to act as sort of a dust cover.
You're technically not supposed to reuse these, however. There's no way I'm finding replacements,
so it's better than nothing. And while I'm here, I'll also just double check that the
fuse stop bar does its job and prevents any further turning of the fuse cone when it's
fully wound up. This is now a great time to lubricate any of the bearings for the pivots.
So with the chain fully wrapped around the cone, that would mean the mainspring
would normally be fully wound up, so I'm going to go ahead and do that now.
Okay, so that's fully wound. Now I'll need to back it off by a quarter of a turn.
Prior to installing the cannon pinion, I'm going to lubricate the center wheel arbor,
the minute wheel post, wind indicator post. So then I can just install this minute wheel,
and then the wind indicator wheel, and finally the hour wheel. Let's do it again.
And the hour wheel, wind indicator wheel. There we go. And that's all that's needed for this side,
so I can actually go ahead and reinstall the dial and work to reinstall the dial screws.
So if you're wondering why chronometers are so important at sea,
well, a chronometer set to a known time standard like Greenwich Mean Time
allows the sailors to determine their longitude by comparing it to local time.
And since we know that one hour of time difference equals 15 degrees of longitude,
the time gap between the chronometer and the local time reveals the ship's longitude. So you
can imagine why accuracy is really important here. I'm going to point this all the way at the
the up line here. Now it's time to reassemble the upper escape wheel sub-assembly, and here I'm
lubricating the cap jewel. Likewise, I'll do the same for the balance jewel. I'm just making sure
the oil ring is perfectly centered. Just checking over the escape wheel before it gets installed,
making sure there's no dust or grime on it. Well, hold on a second. What is... what is that?
What in the amateur watchmaking is this? That looks like a re-pivot job. I suppose that's
good enough for government work, but is it actually good? Let's see. Oh, you see that wobble?
phenomenal. Roller table, the impulse jewel, and the unlocking jewel look fine.
Look at this big old screw. Now the fun of reinstalling the balance stud... whoa...
the balance stud back into the balance cock stay. Gripping this with the wrong hand.
Now I'll reinstall this balance arrestor assembly. It was not installed by Hamilton
from the factory, so this was an aftermarket add-on by the service center.
And the reason why they want to do this is you never really want to let one of these detent
escapement movements to run completely down. So that power can be preserved, but the movement can
be halted for transport reasons. Now if I were to go ahead and arrest the balance,
I simply need to tighten this hex. I think it's in position. Now I drop the screw in from the top,
start to gently tighten it up. With the escapement in place, I can now release the
fourth wheel train block screw. So at this point in time, the train is live. So right now,
the balance is rotated clockwise. If the balance starts swinging counterclockwise,
see how it's grabbing the detent and it's pulling the locking jewel away from the tooth of the
escape wheel? So now the escape wheel was able to unlock a tooth. The escape wheel tooth is now
providing impulse to the impulse jewel of the balance, which would propel the balance further
counterclockwise. And then at some point, the detent drops off of the balance roller and lands
and locks the next tooth of the escape wheel. The balance swings clockwise, comes back around the
other way, and then resets for the next one. You see the little trip spring right there allowed
the balance roller to bypass it to set up for the next pass counterclockwise. And again,
counterclockwise is the only direction the escapement is allowed to occur.
I can now prepare to start the movement at the exact time that I choose. Now remember,
these detent escapement movements, you can only set the time in the forward direction. You should
never set it by moving the hands backwards. So about five seconds now. All right. What's really,
really cool is the detent action happens so fast, you can hardly even tell anything's happening.
So the brass bowl previously was a lacquered brass. The lacquer has worn off in places, which
led to this tarnishing forming around the edges, probably due to the atmosphere that this time
piece had been exposed to, and just the handling over the years. Since this is something that I'm
probably going to be keeping for myself, my personal preference is I want to clean this
up a little bit, restore the satin finish, and put a fresh coat of lacquer on it.
So I've got all the little bits and pieces soaking here in this little jar.
And for the bigger stuff, I just filled it up with lacquer thinner,
and that'll hopefully dissolve the rest of the lacquer. With the rest of the lacquer removed,
I'm going to remove some of this tarnish with some plain old white distilled vinegar
and really fine steel wool. Now I'm just lightly using a brush-on lacquer,
lacquering the surface of the brass. Now this stuff will kind of self-level.
For the smaller stuff, I'm just choosing to use some 50% thinned lacquer and just kind of
dipping it into the solution. It's a little bit easier than trying to brush it all.
Cool. With the bezel warmed up to be expanded enough to be able to install the new crystal,
drops right into place. Second hand is lined up nicely. Every tick is a half second increment.
So it's been about a day. You see the wind indicator, 24 hours has gone by since it was
fully wound up. And it is a couple of seconds slow. These chronometers really should be able
to be run at sub-second accuracy, so I'll be able to regulate that. What you have are these
kind of, they call them Vernier weights. You have a pair of them on each side. You have one
that's a larger one and one that's smaller. So a full turn of this large one will adjust the
watch by 40 seconds. A full turn on this one is more like a couple of seconds. So I'm going to
work to at least turn the smaller one a little bit inward to speed up the watch and do the same
on the other side and then run it for another day and see how close I can get. I'll use a little bit
of Volleycoat DX grease to grease the pivot mounts for the gimbal. Even these pivots can
benefit from a little grease. So I think I'm missing a piece. You see how there's like a
little bushing right here? Well, back here, I don't have one. That gimbal screw is just
going to get pressed right in there. Good as new. So logged in here at time.gov and almost 24 hours
has elapsed, just a couple hours shy, and so far we're running about a half a second ahead.
So, I don't know, I think I'm pretty satisfied with this. From here, I'll just monitor over the
course of several days and sort of average out the performance and see if I need to make any
finer tweaks. It didn't look like it was sitting quite level, so I'm going to make some adjustments.
That's better. The bubble level agrees. Thank you so much for sticking with me all the way to the
end, and to the experts out there, please forgive my amateurness. Oh, and if you're wondering, I
really wish I knew exactly which chip this piece once served on, but all I have are the Hamilton
contract records. And I know I've slowed down on posting lately, but I'll only share new content
when there's a unique watch or a fascinating repair that you haven't seen here before.
Thanks for fixing watches with me today, and I'll see you in the next one.