Pico Prototyping - Building a Pico Uno

Rek XIX
40 followers
1 Video View·Oct 31, 2022
Pico Prototyping - Building a Pico Uno
Today in the workshop we're focusing on the powerful Raspberry Pi Pico microcontroller.
I'll show you three ways of enhancing the Pico to make it as versatile as an Arduino Uno.
We'll also learn how to safely use external power in our Pico projects.
Get ready to do some experimenting and welcome to the workshop.
Well hello and welcome to the workshop and today I'm going to be trying to break a habit that I
have and it's one that you might have as well. Now this isn't a bad habit by any means it's just
one that I think could become a better habit and it goes as follows. Anytime that I get a
new sensor device or I see a new library I want to test it out and the board that I grab to test it
out on is inevitably an Arduino Uno. Nine out of ten times I reach for an Uno first simply because
the Uno is so easy to use even though the Arduino Uno is now 12 years old and there are a lot of
better and more capable boards out there. What I really should be doing is grabbing a Raspberry Pi
Pico. After all the Pico can run circles around the Uno in all performance specifications. It's a
four dollar board and not only can I use C++ and a lot of my existing Arduino code and libraries on
it I can also use MicroPython and CircuitPython with it. It's just a much better choice but the
Uno is easier to use. So I'm going to try to fix that today. I'm going to create not one but three
different versions of the Pico that are very easy to put together. The first one goes together in
five minutes and will let you use the Raspberry Pi Pico in as flexible a manner as the Arduino Uno
is. So let's start out by comparing the Raspberry Pi Pico and the Arduino Uno boards. The Raspberry
Pi Pico was introduced in 2021. The Arduino Uno was originally introduced in 2010. The Pico is
powered by Raspberry Pi's own RP2040 microcontroller chip. The Uno is built around the ATmega328p
microcontroller chip. The RP2040 in the Pico is a 32-bit dual core processor which also includes a
programmable IO section. The ATmega328p in the Arduino Uno is an 8-bit single core system.
The Pico is clocked at 133 megahertz. The Arduino Uno is clocked at 16 megahertz.
The Pico has 264 kilobytes of static RAM and 2 megabytes of flash memory. The Uno has just a
fraction of that with 2 kilobytes of static RAM and 28 kilobytes of flash memory. The Raspberry
Pi Pico requires a 1.8 to 5.5 volt DC power supply. The Arduino Uno can be powered from a 7 to 12 volt
DC power supply. The Pico also has a micro USB power and data connector. The Uno has a USB-B
power and data connector. The Raspberry Pi Pico uses 3.3 volt logic. The Arduino Uno uses 5 volt
logic. The Pico has 26 digital IO ports, 16 of which can support pulse width modulation. The Uno
has 14 digital IO ports, 6 of which can support PWM. The Pico also has 3 12-bit analog to digital
inputs. The Arduino Uno has 6 10-bit analog to digital converter inputs. And here you can see
the connections to an Arduino Uno board. The Uno is ready to use and makes for very simple
prototyping. The Arduino Uno is programmed in C++ and you can use the Arduino IDE,
the Arduino IDE 2.0, or a different IDE such as PlatformIO. Here are the connections to a Raspberry
Pi Pico. The Pico has an advanced programmable input-output or PIO feature. It's also capable
of USB emulation. But when you buy a Pico you're just buying the board. You're going to need to
purchase and install some additional connectors and this is going to mean a bit of soldering.
As with the Arduino Uno, the Pico can be programmed in C++ using the Arduino IDE,
the IDE 2.0, PlatformIO, or other editors. However the Pico can also be programmed in
MicroPython or CircuitPython, making it much more versatile than the Uno for programming.
The Raspberry Pi Pico costs four US dollars. A genuine Arduino Uno from the Uno store will
cost you 23 dollars. However most of us use clone Unos and they can be the same price as
the Raspberry Pi Pico. The Raspberry Pi Pico can run most existing Arduino code. The Arduino Uno
of course has an extensive code base. At four dollars the Pico is certainly inexpensive.
And if you're using clones the Arduino Uno can be just as inexpensive. The Pico Uno however is
going to require some soldering before you can prototype with it. The Arduino Uno is ready to
use and even comes with a USB cable. The Raspberry Pi Pico has an extensive amount of documentation
created by Raspberry Pi. The Arduino Uno also has an extensive amount of Arduino documentation.
There's a rapidly developing base of material for the RP2040 and the Raspberry Pi Pico.
And of course the Arduino Uno has an extensive amount of existing projects and tutorials.
They're both great boards to experiment with, but today we're going to see what we can do about
making the Raspberry Pi Pico as user-friendly as the Arduino Uno board. So here are the two
boards that we have facing off today so to speak. Facing off for the contender of being the go-to
board when you're experimenting and prototyping. And I've got an Arduino Uno clone over here
and a Raspberry Pi Pico. And obviously there are quite a few differences between the two of them.
There's an obvious size difference between the two of them. But one thing that we see when we
look at the Arduino Uno is the thing that we know and love. And that's all of these female
connectors over here. And these connectors will of course make it possible to connect jumper wires
which in turn can go over to solderless breadboards or to sensors. And we can start using our Arduino
right away. In fact speaking of using it right away, when we buy it we also get one of these.
It's one of these little USB cables. So we're good to go. All we need is a computer running the
Arduino IDE or the equivalent. And we can start working with our Arduino. Now let's take a look
at what we get when we get a Raspberry Pi Pico. And this is what we get when we get a Pico. We get
the Pico board itself. In fact when you buy a Pico, if you buy a few of them, you get them on this long
strip. They come in this tape strip. And you just get individual little Picos. And as you can see
nothing else comes with them. There is no cable. But if you have a micro USB cable you can just
plug it into the top over here. And start using your Pico. Now there is no power light on this.
There's not even a reset button. This is a boot selection button over here. And of course we can't
attach anything to it as it is. And so most of us modify our Picos. And we modify them
in order to look a bit more like this. And this is a Pico that's had some male pins soldered onto it.
And the male pins in turn will allow us to do this. And this is a Pico on a sodalist breadboard.
And so this kind of duplicates a lot of the functionality that we have with the Arduino Uno.
We can have the Uno as we have it over here. Or we can have the Pico as we have it here in the
sodalist breadboard. And we can get it all of our pins with wires and that. So these are both rather
convenient arrangements. But there are other methods as well of prototyping with the Pico.
And so let's go and take a look at a few of them. So of course I'm not the first person to figure
out that prototyping with the Pico could be a lot easier. And there are a number of commercial
prototyping products out there that'll make it easier for you to work with the Raspberry Pi Pico.
And one of them might be exactly what you're looking for. So before we build our own little
Pico Unos, let's go and take a look at a few commercial prototyping products for the Raspberry
Pi Pico. So here I have a number of different boards that will allow you to make prototyping
and experimenting with the Raspberry Pi Pico a lot easier. Now over here the first one we'll
take a look at is this Pico Explorer. And this is from Pimeroni. And the way that this works
is you insert a Pico into a socket up over here. So you'll need a Pico that you've soldered all the
male pins onto. And then it brings everything out for you to a number of different points over here
that you can wire to this little solderless breadboard. It's got an OLED display over here.
We've got four different push buttons for the OLED display. There's a piezo buzzer. And if you
look at the back over here, you will see the diagram as to how all of those things are
connected already to the Pico. So you can run some experiments on that and have all these
different components already connected for you. So that's a very handy thing. And this is a Pico
Explorer by Pimeroni. This one over here is by Citron. And this is a really neat little board
actually. I've got one that's already got a Pico already installed on it. But you can also get
these with sockets so that you can install your own Pico. And this board brings a Pico out to a
number of different connectors. It also brings it out to pins over here. So you can get to the
individual pins one by one on these male headers here. It's got a micro SD card. It's got a buzzer
inside of it. It's got an LED up over here. An audio out jack. And it tells you right on the
screening where all of these different components are wired up to. So again it can make your
experimenting and prototyping with the Pico a lot easier. These other two boards from Pimeroni are
basically the same thing. There's two different versions of it. This is a Pico Decker. And what
you do again is you plug the Pico into here. And it brings all the pins out so that you can add a
number of expansion cards to the Pico. And speaking of expansion cards, I've got some over here. Also
from Pimeroni. And these are just basically breadboard cards that you can use to wire your
own circuitry to go on top of the Pico. You can also stack more than one of them over here. And
this one here is basically the same thing except on this one you only get to stack two of them.
And so a number of accessories that you can use to make experimenting with the Raspberry Pi Pico
microcontroller a lot easier. So I think if you were to make a list of the advantages that the
Arduino UNO has over a Raspberry Pi Pico, the list would include the fact that the Arduino UNO
has a number of female DuPont connectors to connect jumper wires to. The Arduino UNO has a power light.
The Arduino UNO has a reset button. And the Arduino UNO can be powered by another power source such
as a 9 volt battery or a wall war to 12 volt power supply. And so what I want to do is create some
Pico boards that give us the same functionality that the UNO has. Now you might not need all of
those features and if so you can create a lesser board. In fact the first one we're going to look
at is something you can literally build in five minutes. It only adds a couple of pennies to the
cost of the Raspberry Pi Pico. And you end up with something that's just about as versatile as the
Arduino UNO. So let's go and take a look at that right now. So once again we're looking at an
Arduino UNO and at its most redeeming feat through the fact that once you get an UNO you can just
take some wires like these hookup wires over here and plug those wires into the IO ports of the UNO
and start experimenting with it. And you've seen some prototyping methods that we can use in order
to get that same kind of flexibility with the Pico. But what I want to show you right now is by far the
simplest method of turning this Raspberry Pi Pico into something a little bit like this Arduino
UNO. And the simplest method is just to get two of these female connectors over here. That's it,
female DuPont connectors. And solder the connectors onto the Pico like this. And I've got one that
I've already done that to. And as you can see this is my handy dandy Pico UNO. It's the simplest Pico
UNO you could make and by far the cheapest. Now I've also soldered a male connector onto the debug
pins. That's an optional thing and you could have put a female one onto there if you wanted to.
But now of course I can take all my wonderful jumper wires and connect them up to my Pico.
And so my Pico is now as versatile as its cousin the Arduino UNO over here. And so what you're
looking at here is version one or the basic version of my Pico UNO. My method of having a
Raspberry Pi Pico microcontroller be as flexible to use as an Arduino UNO. And as you can see I've
got a board with a Pico on it. My Pico is currently flashing because it's running the blink sketch.
It's being powered by a USB connection to my computer. And beside the Pico on either side I've
got the same female connections that you have in an Arduino UNO. So I can plug my jumper wires
in anywhere I want and get access to all of the pins on the Pico. I've also got some connections
down here and that's the 3.3 volt output from the Pico. From the Pico's internal voltage regulator
you can use that to power some peripheral devices as long as you don't go over 300 milliamps.
And I've got some connections here so I can plug into 3.3 volts and ground here. I've also got some
male connections that do the same thing. So I've got quite a bit of flexibility when it comes
to powering things up with my Pico. And down here you'll note that I have another LED and this is a
power LED. So I now have a power LED on my Pico to let me know when I've indeed got power here.
And I have another switch and this is my reset switch. Watch the flashing light when I hold down
the reset switch. The flashing light stopped flashing. When I release it it should start again.
And that's reset the Pico. And so now I've got both the boot cell and a reset switch. The longer
do I need to worry about holding down the boot cell while I'm plugging in the USB cable, I can
just hold down the boot cell and the reset instead. So it's a lot more flexible. And so let me show you
what I used to build this with. What I used is this board over here. And this is board that is
made to emulate a sodalist breadboard. So you can see it's got the exact same pattern as a sodalist
breadboard. The idea is you can take your build from your breadboard and make a more permanent
build by soldering onto here. So these holes are all connected in a line the same way they would
be in a sodalist breadboard. As are these two buses over here. So it made it very easy to wire
something like this up. So let me show you how I hooked up version one of the Pico Uno. So here's
how we're going to hook up a reset button and power LED for our Raspberry Pi Pico. In addition
to the Pico you're going to require a push button, a momentary contact normally open push button,
and you'll need an LED, any color that you like. You'll also need a dropping resistor for the LED
and we're going to use a 180 ohm dropping resistor because we're dealing with 3.3 volts.
We'll begin by attaching one side of our reset switch to the run pin which is pin 30 of the
Raspberry Pi Pico. The other side of the switch needs to be attached to one of the Pico's ground
pins. I'm using the ground pin at pin 38. The Pico's 3.3 volt output on pin 36 attaches to
one side of the dropping resistor. The other side of the dropping resistor attaches to the
anode of the LED. We'll attach the cathode of the LED to ground. We'll also attach the 3B3 out
and the ground connections to the power rails on the side of the breadboard. On mine I also added
a couple of capacitors for noise reduction. I used a 10 microfarad and a 47 nanofarad capacitor
but these are optional. Now here's my Pico Uno version one with the Pico removed from it so you
could see some of the wiring and the wiring is very simple thanks to the use of this type of a
breadboard because of course all of these pins automatically get connected together when I put
the sockets in for both my Pico and the connection sockets outside the Pico. Now you don't technically
need to use sockets for the Pico if you don't want to. You could solder this directly to the board
but if you were going to solder it to the board there is some wiring that you have to do underneath
it so you would either need to have to do that and solder the Pico but not put the Pico all the way
down or you could do the wiring underneath the board but there are three wires to hook up. There's
this one over here from my reset switch and it goes over to pin 30 and then on this end over here
I've got the 3.3 volt output which I believe is pin 36 which goes over to one of the rails over
here the positive rail and the ground on pin 38 which goes to the negative one and then the rest
of my components are all down here in the corner. Now I've got the reset switch itself and since
the reset and the LED both need to the ground they're sharing the same line that's why they're
so close together but you could place them somewhere else if you wanted to. Here's that
ground that they both share being run out to the bus. Here's the resistor the dropping resistor for
the LED and it's being run to the positive side of the bus and you'll notice I put two capacitors
onto the bus. I've got a 10 microfarad and a 47 nanofarad capacitor just across the 3.3 volt bus
and I just like doing that to smooth everything out but otherwise the wiring again has been made
very simple by using one of these breadboards. It's really just a bunch of female DuPont sockets
that have gotten soldered onto a board and the wiring is kind of already done for you
and so as you can see in most cases this would suffice to replace an Arduino Uno
with a Raspberry Pi Pico in terms of experimenting. However there is one case where it isn't and for
that we need to look at the more advanced version of the Pico Uno. Now the two Pico Uno boards that
we've built have already turned our Pico into a pretty versatile little device. We can use it in
the same fashion we do as the Arduino Uno plugging jumper wires directly onto the processor board to
use in our experiments. But there is one thing the Arduino Uno can do that our little Pico boards
can't do and that's accept an external power supply. Something like a 9 volt battery or a
wall wart a 12 volt power adapter can be used to power up the Arduino Uno instead of the USB
supply. But we can add that feature onto our Pico Uno boards but before we add it we need to learn
a little bit about the power pins on the Raspberry Pi Pico. So let's go and take a look at that first.
The Pico power pins are all in the upper corner of the Pico board. The Pico can also be powered
through the micro USB connector. Vbus is the voltage that comes from the micro USB connector.
It will only be active if the Pico is being USB powered otherwise there'll be nothing on this pin.
When the Pico is powered by USB Vbus is typically about 5 volts. Vsys is the main system power bus.
The main system power bus needs to be at a level of between 1.8 and 5.5 volts and this is the input
for the Pico's internal power supply. Now if the Pico is being USB powered the 5 volts from the USB
will be on this bus and Vsys will therefore have a 5 volt output. When the Pico is not being powered
by USB we can use Vsys as the input for an external power supply. The 3V3EN pin is an
enable pin for the Pico's 3.3 volt internal power supply. Essentially this is the Pico's on off
switch. Internally this input will be pulled high with a 100k resistor so that the Pico's 3.3 volt
power is always enabled. You can disable the Pico's internal power supply by bringing this
input low. 3V3OUT is the Pico's 3.3 volt power output. This is the output of the Pico's internal
switched mode power supply. You can use this for peripherals but remember you can only pull a
maximum of 300 milliamps here. Now when the Pico isn't being USB powered connecting external power
to it is pretty simple. An external power supply is connected to the Vsys pin on pin 39 as well as
to a ground pin. This external supply needs to be in the range of 1.8 to 5.5 volts. This is the input
to the Pico's internal switching mode power supply. This works fine until you plug a USB cable in.
You've now got both external power and USB power which is a situation you want to avoid.
Internally the Pico has a diode that protects the USB port from the external power input
so there's no danger to the USB powered device. However when USB power is connected the Vsys pin
is now an output and is feeding voltage back toward your external power source.
That external power source is unprotected. The simplest way to protect an external power
source is to add a protection diode. The best type of diode to use here is a Schottky diode
due to its low forward voltage drop. The diode will provide some reverse current protection and
will avoid the situation in which the USB power is attempting to charge the external power source.
Even using a Schottky diode however there is some voltage loss with this system.
A more advanced system of protecting an external power source is to use an electronic switch.
This external switch can be triggered by the Vbus pin which as you'll recall will go to 5 volts when
a USB power source is attached to the Pico. You want to have your switch to go off when it detects
that Vbus is at 5 volts. An arrangement with an electronic switch will provide a very minimal
voltage loss for the external power source. An ideal component to use for this type of switch
would be a P-channel MOSFET. Unlike the N-channel MOSFET that we normally use in most of our designs
the P-channel will turn off when 5 volts is at the gate which is exactly the operation we want.
So as long as you heed the warnings about using external USB power at the same time
you can definitely supply external power to the Raspberry Pi Pico.
So now that we understand the power considerations it's time to build the
ultimate Pico Uno. One that has a jack on it to allow for external power. Now a couple of things
about the build that I made. First of all I used another proto board for it. Not the same one that
I used in the Pico Uno with the reset switch but a similar one. It also emulates a solderless
breadboard but it has a place on it to allow external connectors including a 2.1 millimeter
power jack. So I used it because of this feature but you could use the same board I used to
construct the Pico Uno that just had the reset switch and the power LED and it would work fine.
There's enough place on there for a 2.1 millimeter power jack or whatever power jack you want. You
don't have to use the same type of power jack. In a similar fashion you don't need to use the
same buck converter that I used. Now I use the Mini 360 which is a very common buck converter.
It's very inexpensive. You can get it on Amazon or eBay but they also have a lot of other suitable
buck converters. You could also use a three pin linear regulator because that's after all what
they use in the Arduino Uno. So you don't have to feel that you're glued into using the exact
parts that I used. So with that all said let's go and take a look at the ultimate Pico Uno with an
external power input. And so here we have version 2 or the deluxe version of the Pico Uno. Now this
will do everything that the Uno will do and as you can see it's doing one thing that the Uno can do.
It is being powered by an external power supply. So right now I've got a 9 volt battery plugged
into a barrel connector over here but it could also have used a 12 volt wall wart if I wanted to.
And you can see my Pico is flashing again because once again it's running the BlinkSketch
and otherwise this is identical to the previous version in that we have a reset switch over here.
So if I hold that down you can see I've reset and there we're going again. And I've also got a power
LED here and this can be powered by either the USB connector or by an external voltage on the
connector over here. And the voltage range is pretty well the same range as it is for the Arduino Uno.
And so there you go the deluxe version of the Pico Uno. Now let me show you how you can build one.
Now here are the parts that I used in order to construct the deluxe version of the Pico Uno
board. And like any of these boards you can make use of things that you already have or you might
want some additional enhancements to it. It's your project. But what I built my project around was
this board over here. Now this is similar to the sawdust breadboard emulator circuit board that we
saw earlier. That's exactly what it does over here. It's again emulating a sawdust breadboard.
But it also has a place up over here for a couple of common components and one of them
is a barrel jack. And that's why I chose this board. I got this on Amazon. I've seen a few
different ones on eBay with different components you can get. So if you can find something like
that that already has the power jack you can go ahead and use that. Otherwise you could use the
exact same board as we did for the last design. If we take a quick look at the last design over here
there is plenty of space on here for a power connector and for the voltage regulator. So you
could build it on this as well. But I thought that this board that had the place for the
barrel connector right at the front over here was a lot easier. Now these are the other components
you're going to need to build it. You're going to need 4 20 pin female connectors. You're going to
need a couple of smaller female connectors for the power bus and also some male ones that you
can cut down to size for that. Now this is the voltage regulator that I used. It's the mini 360
voltage regulator. You do not have to use the same regulator by any means. There are a number of other
things you could use. You could use another small buck converter module like this one over here.
You could also use a analog linear voltage regulator and just use one of the three pin
regulators that would work just fine. In fact that's what they use in the original Arduino Uno.
So anything that can bring the voltage down to about 5 volts is what you want over here.
I've got my Schottky diode over here. It's best if you can use a Schottky diode. You'll get better
performance out of it and you'll get a lower voltage drop across the diode so it won't run as
warm. But you could also use something like a 1N4007 and that would probably work just fine.
My two capacitors, my two 10 microfarad capacitors, my LED and the dropping resistor for the LED,
and a 47 nanofarad capacitor. One of these capacitors here and the 47 are just to go
across the supply voltage and the other one is on the output of the buck converter slash
diode arrangement. It's just the voltage output that goes into the Vsys on the Raspberry Pi Pico.
And so these are all the parts that you need to put something like this together and otherwise
the wiring is very similar to what we did before. But let me show you what enhancements you have to
in order to add external power onto your Pico Proto board.
So to build our advanced Pico Uno with the external power supply we're going to begin
with the exact same circuit we used for the Pico Uno we built that had the reset key
and the LED for power. So you can use the same board that you've already built or start a new
one. In addition to those parts you're also going to require a voltage regulator or buck converter
that can have an input of somewhere between 7 and 12 volts and produce an output of about 5 volts.
Now I used a mini 360 buck converter but you can use a different buck converter or you could use a
three pin voltage regulator. You'll also require a power jack. I used a 2.1 millimeter barrel jack
but you could use whatever power plug makes sense to you. We'll require a diode and I used a 1N5817
Schottky diode. You could use a different diode if you wish as long as it can handle a current
of at least one ampere. And we'll require a 10 microfarad capacitor. We'll begin by connecting
the ground connection of our power jack to the regulator's negative input. We'll take the power
jack positive terminal and connect that to the regulator's positive input. The regulator's
negative output will be connected to our existing ground system. The positive output of the regulator
will be connected to the anode of the diode. The cathode of our diode will go to the Pico Vsys pin
which is pin 39. We'll also connect Vsys to the positive side of our capacitor and we'll connect
the negative side of our capacitor to ground. And this completes the wiring of our advanced Pico Uno.
So here's my deluxe Pico Uno with the Pico taken out of it. So you can take a peek at the wiring
that goes on underneath the Pico board. Now a lot of the wiring is the same as what we used
in our previous design and the one that just had the reset switch and the power LED. And so that
would be the same wiring over here that we have going to the bus and that just moves over down
to here. Pin 36 is the 3.3 volt out and pin 38 is the black one the ground out. Now these connections
over here are the ones that come from the barrel jack and they run over to this point on the board.
They also have a equivalent point on the other side of the board here that they run to. And so
I'm running those down to the input of my power regulator, my buck converter, the mini 360 that
I'm using. Now again you could be using a different converter or you could use a three pin linear
regulator over here. You'd still need to run the power down to it. And on the output here I'm not
sure if you can see it because it's black on a black background, but my diode is buried back
over here as is the capacitor that's on the output. And then the rest of the components are the same
components that we saw earlier. The two capacitors that I put across the power bus, the resistor I'm
using as a dropping resistor for the LED, and the push button switch and the LED are sharing a common
ground and that wire goes down over here. And so the wiring again has been simplified by use of a
breadboard that already is pre-etched in a pattern. And again the pattern being the same pattern as a
solderless breadboard. So it makes all of this wiring over here a lot easier. You don't have to
make the 40 different wiring connections out. You just have to put these down on the board and
solder it as if it was a custom design printed circuit board. And what you end up with is a
really handy way of experimenting with the Raspberry Pi Pico. A way that makes it as easy
as using an Arduino Uno. Well at the beginning of the video I said I was trying to break the
habit of always grabbing an Arduino Uno every time I needed a board to test something out with.
And I think with our last couple of iterations of Pico Unos that I've found the board that I'll
be using. So I'm sure you're going to be seeing a lot more from the Raspberry Pi Pico and other
RP2040 boards here in the DroneBot Workshop. Now if you want to get the schematics for our Pico Unos
or get some more information about the Pico Power, you can check out the article that accompanies
this video. And that's on the DroneBotWorkshop.com website. There's a link right below the video to
that article. And while you are out there reading the article, perhaps consider subscribing to my
newsletter. It's not a spam letter of course and it's not a sales letter. Just my way of letting
you know what goes on here in the workshop. And when you're on the website you'll find the link
to subscribe to that newsletter. If you want to discuss the Pico Uno or the Pico in general or
anything else electronic, well head over to the DroneBot Workshop forums where you'll find over
3,500 other people who love to discuss electronics with you as well. And the forum is free to join.
There's a link to the forum right below this video. And finally if you have not subscribed
to the YouTube channel, please do. I make videos pretty consistently these days about electronics,
microcontrollers, things like the Arduino Uno and the Raspberry Pi Pico and a lot more.
And to subscribe all you need to do is click on that red subscribe button. And if you also click
on the bell notification, and assuming you have notifications enabled for YouTube, you'll get
notified every time that I make one of these videos. So until we meet the next time, please
take good care of yourself, please stay safe out there, and I will see you again very soon
here in the DroneBot Workshop. Goodbye for now.
