Narrated Glassblowing Process - A Truly One Of A Kind Pattern

Timeless Tapestry
4 followers
8 Video Views·Nov 5, 2025
Today in the studio were using recycled piece of glass from past work to make a one of a kind pattern. These pieces are always fun to do from time to time and we never know what the end result will look like. Hope you enjoy the process!
Thank you very much for watching!
If you would like to purchase this piece, you can find it here:
Website: https://glassgoof.com/products/2025-r...
Etsy: https://glassgoof.etsy.com/listing/43...
Twitch: / glassgoof
Please check out our Etsy store where we sell all of our work.
Website: https://glassgoof.com/
Etsy: https://www.etsy.com/shop/GlassGoof
Discord: / discord
Instagram: / glassgoof
Tiktok: https://www.tiktok.com/@glassgoof?lan...
Hey everybody, welcome back to the studio. Today we're going to be making a pretty unique piece
using some recycled glass from many different pieces from over the rest of the year.
I do these periodically and we had a lot of these kind of leftover pieces lately so I thought we'd
throw one together. So I hope you guys enjoy it but let's go ahead and head to the studio,
we'll go ahead and get started. So these little circular discs are what we know as like,
we call them cutoffs. Basically whenever we do cane roll-ups in the studio where we take cane,
roll it up into a little cylinder, we have to do what's called a termination. So we get rid of the
end of it, just a little bit of cane on the end of the roll-up. So that's basically what we're
going to be using today to make a piece. I've got a bunch of them from a lot of different pieces
over the year, maybe even some from years before, but we're going to lay them out just like we do
canes on a little pastorelli plate. We'll smush them together and then we'll be able to create
kind of like a one-of-a-kind pattern that's kind of like a mix match of like all the different
pieces we've made over the last little while. So we're going to lay them out on this little
ceramic plate right here to create like a little grid and then we're going to want to slowly heat
them up. So we're going to throw them in what we call a garage and once it's in there we'll turn
it on. It'll slowly start to heat up to about a thousand degrees and once it's nice and preheated
we can go ahead and take it out of there and start to really heat it up to a nice temperature where
it'll start to actually become molten. So we've got this in the garage, we'll go ahead and click
it on and now while that's preheating I'm going to go ahead and set up the rest of the studio.
Alright so now we're nice and hot and we can go ahead and get to work. I usually get here about
an hour and a half before my slot starts so I can prep everything and it takes about that long for
all the equipment to heat up to the correct temperatures too. So now that we're good to go
we can actually start. So we preheated all these discs to about 900 degrees and now we can transfer
them over to the glory hole so that they can actually become more molten. We want them all
to be able to fuse together so it creates a nice flat plate on top of our pastorelli plate.
It's literally like a vacation for my dog. Yeah if your dog is having a good week it
makes you feel good about it. Yeah of course. You don't feel bad about going out of town or whatever.
You'll notice that we flip the plate around a lot whenever we're heating it up and that's
because the heater, the burner, is really on one side of the glory hole so one side heats up a
little bit faster than the other side. So we want to make sure everything's nice and even heat
so we want to flip it every time that we come back out.
Told you man that cat was...
All right so now you guys can see after about four or five heats it's really starting to get
hot. We've got that nice red glow. Everything's going to be really sticky. It's all stuck together.
So now I'm going to go ahead and make what we call a collar. So I'm going to get a small bit
of glass out of the furnace. I'll come on out and then I'm going to hold it up let the glass fall
back a little bit and you'll see me blow a bubble through the end of it. It's going to be a really
really thin bubble. Once this bubble's formed I can stick this back into the furnace. That thin
layer of glass will kind of shed away and then I'll have a straight shot of the tube, the blowpipe,
and on the end there's basically going to be a clear ring of glass which is what we call a collar.
I'm going to take a seat Luke. So what we're going to use this collar for is we're basically
going to use it to roll that little roll up of all the cutoffs up into a cylinder around it.
I have a small amount of time to manipulate it so that it's just the right size to roll it up
perfectly into a nice little cylinder. We use a pie divider which takes the length of the roll up
and tells me exactly what the circumference of my collar needs to be. So I have a small amount
of time to manipulate it before it cools down. We're going to make sure it's just the right size
and then once my brother Luke has this at just the right temperature we're going to go ahead
and roll it up onto the blowpipe. All right there we go. So now we
have it all rolled up on the pipe and we can start to close it off and try to get rid of all
those gaps. These are really cool roll ups. I enjoy doing these. I've only done a few of them
but they're always so much fun whenever we do them. You get a pattern that you really can't
even imagine until it's done. To give the people what they want. I'll be like this is my cameraman.
Do this man. So now I'm going to go ahead and make sure that all of the tips are touching and
we basically have a nice cylinder but then after that it's going to be a lot of trying to minimize
all the holes in between it so we have a nice flat surface on the outside. So from here on out it's
going to be a lot of pushing and pulling and rolling around on the marver and really trying
content. I thought you were going to do a snake. Especially for a short. Yeah maybe not for a long.
Yeah go for it and push down. All right you can stop. You can push. It does look cool.
Okay so with that last move we're all done compressing. We've got a nice flat surface
on the outside. So what we're going to do is we're going to take this small bit of clear glass that
Luke has on the marver right here and I'm going to use it as a cap to kind of seal off of that
little tube right so then we'll have a completely encapsulated bubble on the inside. So traditionally
we would just cut off the end and do a regular termination which would create another one of
these little cutoffs but I want to maintain the pattern so instead of doing it the traditional
way we're just going to use this little clear bit to cap it off on the end. You can blow.
Really light on. Blow again. Break dance right there. Okay so with the tip of that cut off we
basically have our pattern fully formed. Everything's encapsulated and from here on out
we're just doing some pretty basic vessel making. So we're going to make sure it's nice and smooth
on the outside. We'll add another layer of glass out of the furnace and then we'll be able to just
create the vessel and make our final form. I don't think so. I was trying to listen.
Nope no hole. Yeah I like it. So for anyone who doesn't know this is our glass furnace.
It's a 2000 degree cavity that stays on 24 7 and it houses exclusively all of our clear glass.
So inside there it's basically like a big bathtub full of like 2000 degree molten glass.
So I dip my pipe in get a little bit of clear and this is what we call a strip gather where
I can hold it vertically and get rid of any excess glass that I don't need.
You've probably seen me use this wooden tool quite a bit. This is called a block.
It lives its entire life in water and it's really good at manipulating the molten glass
and cooling it down at the same time. Now that everything is right around the same temperature
and we have that final layer of glass we're just going to start to inflate it. So I'll use my
newspaper tool and I love using this tool. You'll see me use it quite a bit. It really helps me
control where the bubble goes and I'll have my brother Luke blow into the pipe and we'll start
lightly. Blow hard. Off. Pull jack line. See this one got really big. That's good. Yeah it kind of
looks cool though it got big. Yeah. So we've thinned out the neck quite a bit which is exactly what we
were trying to do and now I really want that back area where I'm hitting it with the flame to heat
up because now we're going to put in our jack line. So the tool in my hand is called the jacks
and I'm basically making a small incision right off of the tip of the pipe which is kind of deciding
exactly where we want it to break off of the piece in the end. We're going to do a transfer to a
different pipe a little later in the process and this is going to be the area where we want it to
disconnect from our pipe. At this point in the process this piece really started to fight me.
You can see that part of the surface is getting kind of bumpy and a little bit blown out.
That's because a lot of these different cutoffs were made in different ways with different colors
and they all interact with heat differently. Some spots heat up faster than others some were thicker
than others so it's really fighting me at this point. You know so I did as much as I could but
certain things like this are just kind of difficult to manipulate because of how they're built.
Yeah see you don't want to do nothing man. Off. Oh they start flattening. Yeah. So the piece has all
the volume we want and so now we're going to start to establish the bottom. So my brother's going to
take a wooden paddle and he'll start to really press in to establish the where the bottom of the
piece is going to be. So now that's really starting to thin out you can really see all those colors
again. You know at 2000 degrees everything just looks really orange but when things start to
really cool down and hit that more like 1500 1200 degree kind of mark you can really see the colors.
And we're actually going to prep for that transfer now that I was talking about before. So my brother
has the pipe we're going to transfer it to in his hand. He's got a small bit of glass on the tip
that's going to act as a piece of glue and we're going to stab it onto the bottom of the piece.
We'll break it off of the pipe that I have and we'll have it transferred onto the one in his hands.
Okay. So we have the punty stabbed on. It's right in the middle of the piece which is exactly where
you want it to be just for symmetry. I'm going to add some water right where I want it to break off
and in a moment you'll see me lift the pipe off the rails. I'll give it a tap of my tweezers and
we should be disconnected. All right so that went great. That was awesome. So now we just have to
open up that lip to our final kind of size and we'll have our final piece. Making it real tall
like pulling that cone out. So you'll notice after this heat things started to get a little bumpy
right and those are the thinner sections that are just starting to fling further and further out
because of centripetal force right. You can also see some of these little circles the little cutoffs
are much bigger than the other ones because they were thinner or they were darker color
and so they just kind of blew up and got a lot bigger. Those are also the thinner sections of
we have to do is we'll disconnect it from our pipe. We'll transport it into a kiln to cool overnight
and then tomorrow morning we can come back and we'll be able to see what our final product looks
like. And here we go. This is the final result. I'm really happy with how it turned out. I love
all these circles. You know it has such a cool kind of one-of-a-kind look to it. I love this
piece. You know it came out better than I ever thought it would. So guys if you're interested
in purchasing this piece it is for sale. It's on my website. You can find a link to it down below
in the description either to my Etsy page or my personal website. Either one will be listed on.
And I also want to say we're starting to do live streams sometimes throughout the week.
We're shooting for Tuesdays and Thursdays. We're going to see how long that sticks but
check out the link in our description and you'll see that there's a link to our Twitch page where
you can find us going live. And thanks for hanging out with me today everybody. You guys are the best.
I can't tell you how much I appreciate each and every one of you. Y'all be safe out there and
we'll catch you in the next video.
