ORDER ROLLBACK KITS If you would like a Rollback Can kit please contact me at elementarysciencenight @ gmail.com Let me know you address and number of kits you need.
Chapters 0:36 Rollback can experiment 0:45 Science behind this experiment 1:48 What you need for this experiment 2:16 How to put it together
What you need: (2) 6" paper plates (3) #64 Rubberbands (4) Washers (2) Craft sticks (1) zip tie 6" (3) Large paper clips (1) Correlated cardboard piece 6" x 17"
The Science Behind the Rollback Can
A lot of the moving energy from pushing the Rollback Can gets stored in the twisted rubber band. This stored energy turns back into moving energy as the rubber band untwists. The thin edges of the can help it roll with less rubbing, so it can come back almost to where it started on a flat surface.
The weight inside the can gets pulled down by gravity. If the weight doesn’t lift up and go over the rubber band, the band twists tighter and tighter as the can’s ends spin. This happens after you give the can a little push or roll. The twisting rubber band saves up stretchy energy. At some point, all the moving energy turns into this saved energy and a bit of rubbing. When all the moving energy is gone, the can stops going forward (that’s when things are even, with no extra push).
The rubber band puts a twisting push on the ends of the can and the weight in the middle. Only the ends can spin if the weight can’t be lifted over and around the rubber band. The saved energy in the twisted band gets let out as the can spins the other way, moving back to the start (that’s when things are uneven, with extra push).
Sometimes the rubber band gets twisted so tight that the weight lifts up and spins around the band in the other direction, untwisting it. Some of the saved stretchy energy turns into moving energy for the spinning weight, so the can won’t come back quite as close to the start if the weight stays below the twisting rubber band.
Hey, welcome back to kids fun science. My name is Ken.
Today's experiment is the rollback can. So actually today I'm not using a can.
I'm using correlated cardboard, paper plates, craft sticks, rubber bands,
and washers. All that's listed in the description below.
But this clever device teaches you how stored up energy can be pushed into
motion, right? So when I push this device,
it's going to go about eight or 10 feet and it's going to come right back to me,
which is super cool.
So I'm going to teach you the science behind it, how to make it, what you need.
So, uh, all next. So come along, let's have some fun.
Here is the experiment. Just kind of give a shove.
It's going to roll out about eight feet and it's going to come right back.
How awesome is that?
So the science behind it is once you give the can an initial push or rolls
forward, that gains kinetic energy, the energy in motion.
As the can rotates forward,
the weight inside is due to its mass inertia resists the rotation initially and
lags behind causing the rubber band to twist around it.
This twisting action converts the cans kinetic energy into elastic potential
energy store in the stretch and wound up rubber band.
Once the forward kinetic energy is depleted and it can't momentarily stops,
the twisted rubber band begins to unwind.
This releases the stored elastic potential energy back into the kinetic energy,
but in the opposite direction,
causing the can to rotate backwards all the way to you, which is pretty cool.
This process demonstrates conservation of energy.
Energy isn't created or destroyed,
but transferred from one form to another kinetic to elastic potential to
kinetic. If you like this experiment,
please remember to click thumbs up and subscribe. It does help my channel.
And next I'm going to show you what you need and how to put it together.
What you need here is two six inch paper plates.
So you poke holes right in the middle there, um, just with anything pencil.
Then you got four washers, um, sizes listed there. Two six inch, uh,
craft sticks, a zip tie,
three large paper clips and three number 64 rubber bands and a 17 inch by six
inch correlated, uh, cardboard.
Now I have these in the description of how you can order kits through me. Um,
that's what you need.
First step is to take your three number 64 rubber bands and you're going to tie
them together. So they're all together.
So you kind of put one underneath there and you pull it through and you should
have a little knot right there.
You're going to do the same exact thing on the other side. Um,
once you get those all three tied up, it'll look like this.
And when you pull it out,
all three are tied together and you can see three little segments right there.
And that's what you're supposed to have.
Now you take your four washers and your zip tie and you're going to put the zip
tie right in between all four of them.
And then you're going to put that into one of the knots of the band.
Doesn't matter which side you do.
Just kind of slide it in so it hooks on into that one knot one way.
So once you get that zip tie it, but don't do it completely tight.
You want a little loose so it can spin around a little bit.
So when you pull it down, it's going to be about to right there.
So you have a little bit of space in between just like that.
And then you're going to cut off that excess zip tie.
So now you're just cutting off the excess zip tie.
Don't cut the rubber band right there and then you get rid of that piece and
you're ready to go for next step.
So you take one of your paper plates and you're going to put the rubber band,
the side of the washers there on the inside of the plate where the food would
be.
You're going to push it through and then you're going to see it come through.
You're going to take one of your six inch craft sticks and slide it right through
that hole.
Then pull from the inside so the craft stick is nice and tight.
And then it looked like something like this there.
Next step, take your correlated cardboard, wrap it around in a circle.
So it's going to be able to fit the six inch plate.
So kind of move it around so you get the fit.
Then you're going to take your large paper clips and you're going to put one on
each side where you see the paper coming out on the inside there.
And then you're going to flip it over and put the third one down right where it
kind of folds out there.
And that's what it got right.
And results there.
So it's a nice little circle, about six inches, uh, fit into the plate.
I'll put this over the plate that has a rubber band all the way through the
craft stick.
Then take the other plate with it, uh, food facing down, slide the rubber band
through again, and then now you're going to pull it all the way through it.
So you go past the knot.
So you're going to keep pulling that up and then you see the knot and then
you're going to put the craft stick right underneath that knot.
So, um, when you get the, open it up and then put the craft stick in.
And then make sure it's centered because you don't want it sticking over the
edge, um, all the way there.
And then you're a set just like that should look just like that.