Japanese woodworking - Tokonoma: How to Finish it

Shoyan Japanese Carpenter
89 followers
4 Video Views·Apr 4, 2023
Hello, this is Shoyan, a Japanese carpenter.
Today, I'll finish this space called Tokonoma
that is Japanese-specific space for the ornament.
First, process the materials.
This Tokonoma is small,
but I use natural woods of Zelkova for all members.
Even for a thin skirting portion called Zoukinzou,
I use Zelkova.
However small the material is,
I apply glue on the end section of it to prevent tears.
Without applying glue, Zelkova tends to tear soon.
Before planing it, I'm checking if there is twist.
Fortunately, there is no twist.
It's very steady timber.
Plane the materials by the automatic planer.
Start from the floorboards.
This board is 60mm thick.
Actually, 30mm thickness is enough for this member,
but I use this 60mm thick material.
Thicker is better to prevent deforming.
This is the first time for me
to use a material of this thickness
for this size of floor.
Plane the stiles as well.
Straight grain surface will be the top side,
and cross-cut grain surface will be the front side.
The grain of this material is clear and beautiful.
OK, I've finished planing all members.
Next, adjust the edge shape of the whetstone.
These days, there are many whetstones of diamond,
especially for adjustment of whetstones.
But I use whetstones made of fine sand.
Then, sharpen the blade of the manual plane.
It's very hard to plane Zelkova.
It can be planed only by hard blades.
Let's plane it.
There are not much wood shavings coming out.
I plane it little by little.
At the bottom of the surface of the stile,
make a bigger chamfer.
I don't make a chamfer of 45 degrees,
but I make it loose angle seen from the front side.
This is a special shape of chamfer for stiles.
Next, plane the floorboard as well.
The floorboard is cross-cut grain,
so it's easier to plane.
If it's straight grain, it's hard to plane.
I found that this material is very easy to plane.
This board is made of very steady Zelkova.
I think it will not be deformed more in the future.
Adjust the shape of the floorboard and the stile to fit well.
It's difficult to adjust at once.
The color of the stile and the floorboard is similar,
so if there is a gap, it will stand out.
If the color is opposite, it's easy.
But this case is difficult to adjust the shape.
Light up the space to see the gap carefully,
then fix them.
Make the member called tamabuchi
that will be installed under the stile.
It's the same member.
It will be the ornament under the stile.
Among carpenters, the floorboard is called jiita.
The stile is called tokobuchi,
and the material under tokobuchi is called tamabuchi.
Tama means ball in Japanese.
The front side of tamabuchi will be round shaped.
OK, let's finish it.
First, install the substrate material of shikii.
As well as general shikii,
decide the dimension based on the character of the column.
This material will be visible only from the front side.
The thickness will be the thickness of tatami plus 3 mm.
Apply glue just in case.
As well as kamoi,
the surface of it is offset from the columns only a little,
not too much.
If it's offset too much,
there will be the gap between tatami and shikii
after shrinkage of materials later.
So make shikii offset only a little.
Install tamabuchi for a trial.
Cut the stile.
At the same time of cutting the stile,
make a small piece of the stile
to draw the marking of the stile on the column.
Only by measurements of dimension,
the marking will not be matching.
Cut off the portion where the stile will come.
Regarding the top side,
using a fine toothed saw, cut off it carefully.
It's very difficult to make a notch for a stile on the column.
If it's a big notch, it's easy.
At the top side and the bottom side,
the shape of the notch should be the same as the chamfer.
The column is white,
so even small mistake will stand out.
So cut off it carefully.
OK, the notch is fine.
Let's install the members.
Tamabuchi cannot be fixed by screws.
It's not the portion stepped on,
but fix it by glue.
Install the stile from the back side.
I applied glue too much.
Remove the glue by wet clothes.
If I use dry tissue,
glue will get in the fibers of the alcove.
If so, the portion cannot be painted.
So glue should be removed by wet clothes.
The forward is too wide,
so cut off the edge of the board.
Fix the substrate materials.
Adjust the position of the substrate materials
using the cut-off piece.
Fix it at the position of 1mm down.
It cannot be flat.
Unlike the stile at the entrance,
the gap here is not too much.
As you can see,
this is very steady silcova.
In usual cases,
the kickback often happens
while using circular saw.
It's rare that the saw moves smoothly like this.
It's very steady.
This board is narrow but thick.
It's difficult to cut it diagonally,
so I cut the back side wrongly.
This time, the floorboard is thick material,
and it's very steady silcova.
So I don't use the substrate material
to prevent deforming of the floorboard.
I fix it with strong urethane glue.
Use wedge to adjust the position towards the stile.
To fix it,
I don't drive in screws from the top side directly
into the floorboard.
Use substrate materials
and push the floorboard indirectly.
And drive in screws from the back side
as soon as possible.
I don't drive in screws at once.
I drive in screws by two times.
Silcova is hard,
so screws are sometimes broken.
If screws are broken,
they can never be removed.
So reduce the resistance
and drive in screws carefully.
Install ceilings.
Fix the member called kumoita.
Kumoita is the prevention of the damage
on the wall by scroll.
It's the board fixed under the cornice.
Next, fix zoukinzuri.
Zoukinzuri is also made of silcova.
Fix it by thin screws.
Zoukinzuri is the prevention
of stains on the wall
while wiping the floor.
It's the member to stop a floor collapse.
Lastly, fix the substrate materials
of walls and install gypsum boards.
This room will be finished by plaster.
So this dokonoma
is also finished by plaster.
OK.
Now I've completed small dokonoma
with natural woods.
It's charming.
That's all for today.
Thank you for watching.
