It's Alive! // 2UZ V8 1974 Celica

ThrottleStream
1 follower
Aug 2, 2024
Quality Car Builds Don't happen Overnight!
Support This Channel❤️
⭐️Merch: https://shop.sarahntuned.com
Shoutout to @JimmyOakes for helping make this engine come to life.
Patreon: https://www.patreon.com/sarahntuned
Amazon Store: https://www.amazon.com/shop/sarah-n-tuned
Website: https://www.sarahntuned.com
Instagram: sarahntuned
Facebook: sarahntuned
X/Twitter: sarahntuned
Special Thanks to my Patreon Support!
Britt F.
Chad B.
Col. L.
Curtis S.
Daniel F.
Darren M.
Dave
David L.
Jeffrey P.
Josh H.
Kevin C.
Mark L.
Meghan "in Seattle"
Nenad R.
Ray I.
Terry S.
Todd C.
hi people of Earth that are watching car
related internet videos welcome to this
my 1974 ra21 Toyota Celica St with a
2005 Toyota Tundra V8 under the hood and
with the exception of just a couple tiny
little remaining tasks on my maintenance
board I can then attempt a first start
to see if everything works on this
engine now as you clearly see I still
need to bodyw work and paint the engine
bay on this car and it is currently
lacking a radiator however it is not
going to be needed for the first start
this is more about just trying to get
the engine to run to make sure it is
capable of running and it won't be
running for more than a maximum of 30
seconds that way I don't have to waste a
bunch of coolant when I have to pull the
engine straight back out of here to
paint the engine bay for those of you
that were disappointed I didn't start
the car in the previous video there's a
good reason why I didn't and that's
because there was a couple issues right
here that I was lacking that are pretty
critical for a first engine start this
car does have a oil pressure gauge in
the dash and my ECU will be monitoring
it but that is not hooked up currently
oh this fit can I put this in here
that's cute will that fit no this is
like the equivalent of a bag of fruit
snacks but for a baby robot I bought a
cheap oil pressure gauge just temporary
for for start there's a Teflon turd
stuck inside the threading a little bit
of thread sealer on there screw this
right into pretty much the Factory
location now I can at least see oil
pressure at startup make sure everything
is cop pathetic oil Union in out that's
done basically this morning off camera I
just went over the entire car and seven
leveled it one last time to make sure
there wasn't any my new details I was
missing and I did find a couple little
things and for those of you that are
wondering what the hell seven level is
ask some of the Air Force veterans in
the comment section I left all the
header flange nuts loose so I could get
the collector on and I forgot to tighten
them I think I just got my arm
[Music]
stuck one item down couple more to
go yeah this right here is to block off
the port where my IIT sensor will go
when I put one on it I don't have the
gauges hooked up or IIT that's really
the only thing that is not hooked up
again the purpose of this first start is
not to tune the engine or try to drive
the car it's literally just to test the
plumbing and the wiring of everything
make sure it's good before it the engine
bay and subsequently this is also going
to be a brief verification that the
machine shop and engine builder did
their job correctly that's a big step up
but I think I can get it on there I
think also what I want to do real quick
just to be extra
careful oh that sucks I just went to do
this this is kind of excessive but I
just I I'm trying to be super thorough
so I'm going to crack my return line the
sound of a 6 L Power Stroke approaches
wild char has appeared who Wild Charlie
has appeared the
only well unfortunately angel food cake
and Karen are out of town on vacation uh
so they can't be here for the first
start but I called Charlie to come over
so he can at least watch first start
this is literally just a fuel jug that
can be used for like the air compressors
and stuff it's not going in a
car how do it make you stay that's
perfect timing now that Charlie's here
he can help out with this part you're
going to get covered in gas yep Ready
just in case there are any cits left in
the fuel lines this will eliminate them
the fuel lines are nice and flushed now
technically I can use the ECU to disable
the injectors so that way I just crank
it to build up some oil pressure first
but I'm just going to physically unplug
them because I I don't feel like getting
out my crappy $200 Walmart laptop I got
some hair protection in because this
thing is going to be loud watch the oil
pressure gauge it's probably going to
take a couple times oh it's going to
take a
bunch so so I have to use a Power Probe
to simulate the signal for the going to
the starter because I don't have the
neutral safety switch hooked up I got to
I got to bypass
that what is going on out
there oh yeah it's uh it's going to
storm now the Pokey is indoor so I don't
get hail dents on it try this again re
attempt to Prime system
what we should probably go get the
charging cart from next door I'll go
grab that yeah all
right essentially what I'm doing right
now and why I unplugged all the
injectors is just letting it crank over
and slowly Prime the entire oil System
since I have so many oil lines going to
the remote oil cooler and oil filter and
then once I start to see oil pressure
then I can actually hook up the
injectors again and let it fire oil
level is still good yeah it's got a lot
to Prime okie dokie I'm debating whether
I should hook up my laptop so I stole
the gauge I was using for the oil
pressure gauge and real quick I'm going
to set it up on the fuel
return like 40 40 yeah it's about good
right yeah it's about where it should be
for the next go around I hook the fuel
system back up and just in case you
wondering this does have assembly Lube
on all of the internal components of the
engine so it doesn't hurt it by cranking
that starter chill a little bit
oh it's going to start oh that made me
so nervous I
stop still nothing on the whe pressure
gauge I think the engine's got to be
running for it though doesn't it I mean
it might have to like get running for a
second before you see pressure one thing
that is a little nerve-wracking is after
all these test cranks to Prime the
system my oil pressure gauge has not
budged once and I understand there's a
lot of hose for it to fill in the filter
but when I stole the gauge for the fuel
system no oil came out of that and I
need to check that before I try to start
this car
mhm I got nothing crank it for
longer we got an oil typically in this
situation when you rebuild an engine a
way to alleviate this issue is to take
apart the oil pump in packet with
assembly Lube to create a little bit of
suction on Startup to Prime the system
and because it's weekend and it's in the
evening there is no place open that I
can get a pressure from so I
ordered one and paid for overnight
shipping so I guess
[Music]
minana hi it's 2 Days Later package
[Music]
arrived jeez that thing's huge looks
like you cook some crabs in it
advertising isn't free yep all right
well it might look like a piggy bank for
young robots it's actually a pressure
preber for the engine and this package
is some
hose oh it's got a&n fittings on it
fancy wrap this thing in some plumbers
licorice some of you might argue that
the engine wasn't rotating fast enough
for it to build up oil pressure and that
had I just fired it up it would have
built up oil pressure but I like to be
on the safe side because I'm not made of
money on the plus side uh hopefully in
the the next month or two I won't have
to be pushing this car around in the
shop anymore I can just drive it for as
expensive as this thing is it sure had a
lot of crap inside it that I had to
triple flush out of there now that it's
clean I got to make sure this thing is
absolutely dry on the inside or else
it'll
make robot
toothpaste okay I'd say that's good I
don't want to waste this oil because it
was extremely expensive and it's
literally brand new let's see if I can
catch it
without dropping the drain plug into the
receiver that would suck so horrendously
okay here it
goes this is going to take a while
almost
s not even a drop on the ground love
that so I'm going to put this fitting
right here where my an ends go out to
the filter goes directly to the oil pump
and this will fill all the cavities and
oil gys and nooks and crannies and spots
that should be lubed with oil so way I
can start it and not worry about it
being a dry start only doing this just
because it says to in the instructions
of this kit this does have an anti-drain
back valve I don't know why I'm nervous
doing this I'm just like nervous about
everything until this engine
starts feel like I'm hydrostatic testing
a wash cart right now some some somebody
laughed at that all right that's about
55 PSI yeah here it
goes sounds
weird I don't really know how to know if
it's doing what it should be doing other
than like pulling a valve cover I
don't really want to pull out
cover you can hear the oil getting up
into the
heads good it's it like
40ish Psi 45ish Psi this actually takes
quite a while oh
hey instead of letting it froth all the
stuff at the bottom I'm going to stop it
and release the pressure I feel like
that's smarter a little bit more in
there wow I'm an idiot good
job just to be extra safe I'm going to
turn the engine over by hand too and
then do a little bit more
lubing oh jeez
turn a little
bit
[Music]
okay now this engine should be good and
preed and safe to start this is going to
make a huge
mess they just move this thing out I
don't like working around it in that
little crevices that didn't sentence
made no sense I guess hook the power
back up so we got sir Jimmy Oaks
remoting into the laptop right now and
he's going to look at the uh tables the
after start enrichment and
the cranking table I don't remember what
they're called in link so what what are
we doing um I added fuel to the after
start enrichment in the cranking table
just trying to get the car to start and
did it did it run at all it would cough
like it was trying to start okay so I
guess let's key on and then let's try
and start it and I'll get the data and
go from there a wild Charlie had arrived
in anticipation to actually see this
thing run
[Music]
[Music]
now backfired uh yeah try again
okay those are bad fires yeah those are
flames and my knees are right under the
headers holy I felt the Heat can we
just timing light
it
and I'll tell you when I get a good a
good idea all right ready
yep nothing it's not cranking fast
enough to give me a light well it's I
got a just a random shitty spark plug in
here and you can see it spark yeah I can
see the spark too
yeah it's not lighting up not even a
little that could probably be our most
likely if the timing isn't helping it's
probably that so just to confirm
cylinder one is the driver side front
yep cylinder right correct and then two
is the passenger side front correct all
right uh give it a shot
okay started
[Music]
not
bad it have oil pressure uh I mean it
was reading oil pressure when we were
cranking it and the tube is full up to
the gauge so
[Music]
that thing sounds so sick I had like 75
80 psi oil
pressure I didn't have a camera on it
but I had 75 PSI oil pressure at idle so
plenty of oil pressure it's good to go
it runs yeah it sounded way better so
the verdict is the only issue that it
has is the wiring for the cam trigger at
the plug if you shake it it acts
erratically and gives weird readings at
the ECU so that's why I was having
trouble trying to get the timing set for
this thing to start and also I don't
have a working timing light to actually
set it correctly sounded good sound like
a damn V8 that's choppy yeah I I'm sure
that will go away some of it will when
you get the fueling the timing and all
that sorted but
good wow that's quite the
[Music]
Thunder welcome to the third day in this
video fourth day third day day this came
in the mail this is the inside of a
robot chicken's egg in order for me to
know how long of a drive shaft I'm going
to have to put on this thing this this
was brilliant let slide
that all the way in I can't tell I can't
tell if it's hitting the Shield or if
it's going all the way in cuz that's
going to
matter I can't really get a good whack
at it Al like he said I don't want to
just cut that Shield because then it
would be like razor sharp and suck every
time you worked on it under here oh my
brass punch is seen better
days ow that was my foot I saved it
though collar
removed okay
now that's all the way as much as I
prefer metric I live in America so I
need to measure this in
inches except I don't have five arms
conveniently that is about Center using
electrical tape because it makes
sense looks like 46 and
38 just out of curiosity this is the
original drive shaft sat right there
[Music]
oh I don't know actually I'm not a
tubist but I would think that this is
not rated for the amount of torque that
engine's going to put out I'd have to
pop this guy off let just I'm
curious so the carrier bearing used to
sit right
there holy what is the distance
from this to the center carrier bearing
30 and 7/8 that is 100% the exact same
length 30 and 78 Center of yolk 16 in
dead on 16 in holy crap it's the exact
same size and dimensions quite literally
by measurement alone that will bolt
directly into
place I think I don't I would have to
get the U joints are different these are
beefier I got to do my research on this
there's something is going to have to
get upgraded on here but I think that
might and I was going to do a one piece
drive shaft uh there's a lot to
research I don't need any of this
[Music]
anymore that's a lot but that's pretty
much everything to finish the car the
most timec consuming part that is left
is going to be Bodywork and painting the
engine bay which subsequently is the
next thing that I'm going to do so I can
send a bunch of stuff down to powder
coating to get it all ready to install
into the bay some of you might be
confused by the process of how I did
this but I didn't want to have to
majorly modify anything in the engine
bay after the bay had been painted but
now that it's Ops checked successfully I
feel it's safe to go ahead and finalize
everything in that engine bay the next
video I have for you guys is going to be
on the MR2 as well as Forester Gump and
the UR Quattro there's some stuff I want
to do to all of them maybe I can do them
all in one video I don't know I just
need a screw off video just to give me a
mental break but I will do whatever you
guys want to see in the comment section
below let you vote on it and also if
you'd like to support what you see here
on this channel I do not have major
sponsors as you know so um there's a
link to my website below maybe you want
to take one of the little penguins home
they're on there and um yeah thank you
guys for watching I'll see you soon with
another video bye
